Thank you for your confi dence in purchasing our washing machine, and congratulations on the excellent choice. Your new washing machine meets the requirements of modern treatment of laundry. It is rational in the consumption of energy, water and washing agents.
Description of washing machine 1. Front panel 5. Adjustable legs 2. Detergent dispenser 6. Water outlet hose 3. Door 7. Water inlet hose 4. Filter lid 8. Mains power cable Technical information Dimensions (w x d x h): 600 mm x 600 mm x 850 mm...
• When connecting your washing machine to water supply, be sure to use brand new water inlet hose and appropriate sealing gaskets (attached). • Do not locate the machine in a room with temperature below 0°C. Parts of the machine may be damaged if frozen.
Installation and connection Package removal Package removal In removing the wrapping be careful not to damage the appliance with a sharp object. Before connecting the appliance, let it warm up to room temperature (wait for two hours). • Our appliances are packed in environmentally friendly materials which may be recycled, deposited or decomposed without any threat to the environment.
15 seconds. • Take the water inlet hose from the drum and attach the inlet hose angle extension (1) to the washing machine by screwing it onto the provided thread (certain models only). • Insert the gasket with a fi lter net into the straight inlet hose attachment nut (2) and screw the nut onto the water tap.
Page 7
Do not immerse the Aqua-stop system inlet pipe into the water, because it contains the electric valve! Water outlet connection Water outlet connection • Fix the outlet hose to run into the sink or the bathtub, or connect it directly to the wall drain outlet (diameter min. 4 cm). •...
Operation A - program selector knob Signal LED’s: B - delayed start - washing program stages C - setting the spinning speed (rpm) / stop • wash pump • rinse D - quick program or cold wash (depending • spin on the model) - Child lock E - higher water level...
Check that the drum is empty. - Close the door of the appliance. - Open the water inlet faucet. - Push the ON/OFF button and select washing program. Washing machine Washing machine Program is selected by turning the program selector (A) from the operation operation “0”...
Page 10
Cotton: whites/colored Normally stained cotton and fl ax bed linen and underwear, table cloth, bathroom towels, top garments, etc. For heavily stained permanent press use the heavy duty program, or program with the pre-wash For smaller loads (non-delicate cotton, linen, synthetic, and mixed fabric) and smaller quantities of soiled laundry (laundry refreshment, laundry wet with perspiration, etc.), we recommend the use of the...
Page 11
- Selection of additional function ( Additional functions alter the basic washing cycle procedure. Particular function is switched on by pressing the relevant knob. The selection is confi rmed with sound signal and switching on the signal LED above the selected function. If certain function is not available for the selected program, signal LED will not illuminate.
Page 12
Use this function to prevent creasing when you are not able to take the laundry out of the washing machine immediately after the washing cycle is over. This function is particularly appropriate for...
Page 13
- Selection of partial programs ( These are independent programs and may be used when you do not need the entire washing program. In case you would like to use more additional programs in a sequence, you must turn off the appliance prior any new program selection (turn the program selector to “0”...
Page 14
The end of washing program is signalized by fl ashing washing progress LEDs. The message “End” is indicated on the display. • A sound is emitted, indicating that washing machine door can be opened. • Take the laundry out of the drum and remove any remaining particles or foreign bodies from the door seal.
The program can also be changed by rotating the program selector knob to “0” and choosing either spinning or only pumping out the water between additional programs or cycles. Manual cancellation The program is cancelled if the program selector knob (A) is rotated to position “0”.
(“S2”); press the button again to turn the sound signal off (“S0”). The selected setting is stored and remains in memory even if washing machine is turned off. Tips for washing and energy saving • Before washing sort out the laundry according to the type, degree of dirtiness and color resistance.
• If you use thick liquid softener it is recommended to dilute it with water, to prevent clogging of dispenser compartment ducts. • Washing machine is equipped with the dispenser partition gate, so you may pour liquid detergent also into the central compartment (depending on model). If you use powder detergent the gate is lifted up, and in case of liquid detergent it is slid down.
Page 18
• Wash it under running water using a brush, and dry it. Remove any leftover dried detergent from the bottom of the casing. • Clean the entire rinsing area of the washing machine with a brush, especially the nozzles on the upper side of the rinsing chamber.
Page 19
• Open the fi lter lid using fl at screwdriver or similar tool. • Filter needs occasional cleaning, especially following heavily shaggy or old laundry. Before cleaning, drain any water from the machine via drain pipe. • Turn it anti-clockwise, pull it out and clean under running water.
If the fault is in the heating system, the machine completes the washing program, but without the heating function. If the fault is signaled during washing machine operation, the error code and remaining washing time are indicated alternately on the display.
Page 21
Failure Possible cause Remedy The machine does not Machine is not powered. Check if: work (indicator LED’s are • power in the socket, not illuminated). • the fuse is OK, • plug is in the socket. FAILURE 2 Washing program does Door is not properly closed.
Page 22
Unpleasant smell in the • Remains of fabrics, washing • Check whether the fi lter is clean. washing machine drum. agent and softener in the fi lter. • Development of germs • Run the auto-clean (SterilTub) program (see chapter: selecting...
Page 23
Failure Possible cause Remedy FAILURE 5 Motor operation Motor overload or motor failure. • Turn off the appliance and wait for interrupted; or motor does a few seconds; not operate (the machine • turn the appliance back on and reports a failure F5 - the repeat the washing program.
Tables Program chart - 8 kg Water cons. Basic programs Cotton 2,45 Cotton 1,36 1400 Cotton + prewash 1,65 Cotton - heavy * 1,38 Cotton - easy ironing 1000 1,27 Cotton 0,75 1400 Cotton 0,39 Cotton - quick 17’ 1000 0,17 Cotton - Tap Water+ 1400...
Page 25
Program chart - 7 kg Water cons. Basic programs Cotton 2,19 Cotton 1,17 1600 Cotton + prewash 1,32 Cotton - heavy * 1,19 Cotton - easy ironing 1000 1,14 Cotton 0,67 1600 Cotton 0,35 Cotton - quick 17’ 1000 0,17 Cotton - Tap Water+ 1600 0,18...
Page 26
Program chart / Additional functions Program Basic programs Cotton Cotton with prewash Cotton heavy Cotton Cotton - quick 17’ Synthetics with pre-wash Synthetics Delicate Wool Manual wash Partial programs Rinse Softening Pumping water Spinning possibility * depending on model.
Page 27
Maintenance chart Normal wash Max. Max. Max. Max. washing washing washing washing temp. temp. temp. Washing temp. 95°C Manual 60°C 40°C 30°C Delicate wash washing allowed Whitening Whitening in cold water Whitening not allowed Ironing Hot iron max. Hot iron max. Hot iron max.
Need help?
Do you have a question about the washing machine and is the answer not in the manual?
Questions and answers