Connections Using Rs485; Connections Using Rf Output - Nedap Convexs Series Installation Manual And User's Manual

4.4.

Connections using RS485

Convexs/Invexs connected to Nedap AEpacks using RS485: For those
AEpacks not having RS485 on board use the additional AX1012 (RS485
to RS232 converter)
Convexs / Invexs
A1 1 Power / XSMOD
A2 2 POWER GND/shield
A3 3 A (-)
A4 4 B (+)
A5 5 D0
A6 6 D1
A7 7 BEEP
A8 8 UL*
A9 9 GND
A10 10 NA*
Remarks:
1 On AP1003 the RS485 is available on Upper Row connector points 13 - 16, only from PMS D or higher
2 For AP1003 with PMS below D use the additional AX1012 to convert RS232 from AP1003 to RS485 for
Convexs
3 Power for Convexs can be supplied by
- External Power Supply
- AEpack, check correct voltage and current at given AEpack output
4 Beeper on Convexs can be optional controlled
- on AP6003 this can be done by pin 16
- on other AEpacks use Relais output
5 LED control is supplied over the RS485 communication, so no additional wiring is needed
6 Cable shield must be connected to Power GND of Convexs (A2) and GND of external device or metal
case of the external device (at housing of AP6003, AP4x03x, AEbox)
7 If Convexs replaces e.g. DC130 antenna the existing cabling of the DC130 antenna (4 x 0,25qmm) can be
reused for RS485 and Power only if cable length not exeeds 50 meters and cable shield is correct
connected.
8 PIN code for the Invexs reader is transmitted using the RS485 communication.
4.5.

Connections using RF output

Convexs / Invexs
A1 1 Power / XSMOD
A2 2 POWER GND/shield
A3 3 A (-)
A4 4 B (+)
A5 5
A6 6
A7 7 BEEP
A8 8 UL*
A9 9 GND
A10 10 NA*
Remarks:
1 For Nedap reader AEpacks the AX1014 must be applied to
each AEpack
2 For the Accessor III / SimpleXS / AC3/2TR the AB350 must be applied
3 Existing cabling can be re-used when the Nedap antenna is replaced by the Convexs
4 Power is supplied to the Convexs by the RF signals on A1 and A2, no additional Power Supply is needed.
5 Beeper can be controlled optional by making the correct configuration settings or hardware connection.
6 Cable shield must be connected to Power GND of Convexs (A2) and GND of external device or metal
case of the external device (at housing of Accessor, AP4x01, AEbox)
7 PIN code for Invexs readers is NOT possible
8 Invexs 190 to AX1014 or AB350 needs additional connection between GND (for UL and NA) and
Antenna GND on the AX1014 / AB350 (Invexs 190 has no separate cable for this connection)
© Nedap N.V.
AP6003 AP4x03x
3)
Lower 1
14
8
10
4)
16
AX1014
11 – ANT
12 – GND
D0
D1
relay
13 – UL*
14 – GND
8
15 – NA*
Nedap Readers Installation Guide
1)
AP1003
3) 3)
Upper
1 1
14 Lower 1
8 Upper 13
10 Upper 16
-- --
-- --
-- --
-- --
-- --
-- --
AB350
ANT
1 2 3
4 5 6
7 8 9
C 0 E
GND
--
--
relay--
UL*
1 2 3
4 5 6
7 8 9
C 0 E
GND
NA*
1 2 3
4 5 6
7 8 9
C 0 E
2)
AP1003+AX1012
3)
Upper
1
Lower 1
AX1012 Rx+
AX1012 Rx-
--
--
--
--
--
--
AX1014
AX1014
AX1014
AX1014 AX1014
Accessor III /
SimpleXS
AC3/2TR
AB350
Page 14 of 21