REXROTH EFC5610 Easy Start Manual
  1. Manuals
  2. Brands
  3. REXROTH Manuals
  4. DC Drives
  5. EFC 5610 Series
  6. Easy start manual

REXROTH EFC5610 Easy Start Manual

Hide thumbs Also See for EFC5610:
Table of Contents

Advertisement

Quick Links

Bosch Rexroth EFC5610 Frequency Inverter
Easy Start Guide
L1 L2 L3 (+) B U V W
The Bosch Rexroth EFC5610 Frequency Inverter range
is available to order from inverterdrive.com
This guide is intended to complement the user manual provided by the manufacturer.
It is provided as a basic introduction to the product for Inverter Drive Supermarket customers.
It should not be used as a replacement for the manual issued by the manufacturer.
This product is not a safety device. All safety considerations including but not
limited to Emergency Stop provision should be assessed separately and are
outside the scope of this guide.
Issue 1
20180705

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EFC5610 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for REXROTH EFC5610

Summary of Contents for REXROTH EFC5610

  • Page 1 Bosch Rexroth EFC5610 Frequency Inverter Easy Start Guide L1 L2 L3 (+) B U V W The Bosch Rexroth EFC5610 Frequency Inverter range is available to order from inverterdrive.com This guide is intended to complement the user manual provided by the manufacturer.

  • Page 2: Table Of Contents

    Easy Start Guide Bosch Rexroth EFC 5610 Series Inverter Contents Page 1 Contents Page 2 Power and Motor Connections (Single Phase) Page 3 Power and Motor Connections (Three Phase) Page 4 Motor Connections - Star and Delta Page 5 Parameters - Overview...

  • Page 3: Power And Motor Connections (Single Phase)

    Easy Start Guide Bosch Rexroth EFC 5610 Series Inverter 1. Power and Motor Connections (Single Phase) Before commencing, confirm that the Inverter and all cables are completely isolated from the power supply, have been isolated for at least 5 minutes and that the motor is not turning.

  • Page 4: Power And Motor Connections (Three Phase)

    Easy Start Guide Bosch Rexroth EFC 5610 Series Inverter 2. Power and Motor Connections (Three Phase) Before commencing, confirm that the Inverter and all cables are completely isolated from the power supply, have been isolated for at least 5 minutes and that the motor is not turning.

  • Page 5: Motor Connections - Star And Delta

    Easy Start Guide Bosch Rexroth EFC 5610 Series Inverter 3. Motor Connections - Star and Delta Dual voltage induction motors typically include The selection of Star or Delta is not optional terminal boxes with six points. The points can and must match the supply voltage.

  • Page 6: Parameters - Overview

    Easy Start Guide Bosch Rexroth EFC 5610 Series Inverter 4. Parameters - overview The Inverter contains a number of settings The parameters contain critical information which can be changed to tailor it for use in a essential to the correct operation of the wide range of applications.

  • Page 7: How To Set A Parameter Value

    Easy Start Guide Bosch Rexroth EFC 5610 Series Inverter 6. How to set a Parameter value 6.1 Find Parameter Groups. This example demonstrates the steps required to set parameter E0.26 which is Acceleration time in seconds. Press the “Func” key repeatedly until the display shows “-b0-”...

  • Page 8: How To Operate The Inverter From The Keypad

    7. How to operate the Inverter from the keypad 7.1 Use the dial to set the required speed. When the EFC5610 is powered up for the first time without any changes to the parameters it will operate from the keypad. The display will change to show the speed reference in Hz.
  • Page 9 8. How to enable Sensorless Vector Mode The standard motor control mode of the These calculations require a rotating EFC5610 Inverter is VxF. This simple mode “autotune” run with bare shaft during which the controls motor speed by varying Volts and Inverter operates for approx.

  • Page 10: How To Connect And Configure A Potentiometer For Remote Speed Control

    Easy Start Guide Bosch Rexroth EFC 5610 Series Inverter 9. How to connect and configure a Potentiometer for remote speed control If the integrated dial on the keypad is A Potentiometer of 10kOhm rating should be unsuitable for the application, a remote used.

  • Page 11: How To Connect And Configure A Run Forward Or

    Easy Start Guide Bosch Rexroth EFC 5610 Series Inverter 10. How to connect and configure a Run Forward or Run Reverse switch The parameters described in Section 5 enable This section explains how to enable 2-wire Run/Stop operation via the red and green control with Run Forward / Stop / Run Reverse buttons on the Inverter.

  • Page 12: How To Connect And Configure A Run/Stop Switch

    Easy Start Guide Bosch Rexroth EFC 5610 Series Inverter 11. How to connect and configure a Run/Stop switch with Forward/Reverse selection The parameters described in Section 5 enable This section explains how to enable 2-wire Run/Stop operation via the red and green control with Run/Stop and Forward/Reverse buttons on the Inverter.

  • Page 13: How To Configure "3-Wire" Control With Run/Stop

    Easy Start Guide Bosch Rexroth EFC 5610 Series Inverter 12. How to configure “3-Wire” control with Run/Stop pushbuttons and Forward/Reverse selection The parameters described in Section 5 enable This section explains how to enable 3-wire Run/Stop operation via the red and green control with Run and Stop commands via buttons on the Inverter.

  • Page 14: Brake Resistor Connection

    Easy Start Guide Bosch Rexroth EFC 5610 Series Inverter 13. Brake Resistor Connection Before commencing, confirm that the Inverter and all cables are completely isolated from the power supply, have been isolated for at least 5 minutes and that the motor is not turning.

  • Page 15: Sto (Safe Torque Off) Connections

    ‘unsafe’ and Safe Torque Off (STO) is an optional safety feature what safety devices are appropriate for the included with some EFC5610 Inverters. If present, application. the Inverter will include a yellow STO connector. No...

  • Page 16: How To Reset The Inverter To Factory Defaults

    Easy Start Guide Bosch Rexroth EFC 5610 Series Inverter 15. How to reset the Inverter to Factory Defaults 15.1 Select the b0 Parameter Group With the motor stopped, press the “Func” button repeatedly until the display shows “-b0-” (do not press and hold the “Func”...

This manual is also suitable for:

Rexroth efc5610

Table of Contents

Save PDF