Sony 500WSPL Operating Instructions Manual page 88

Viewfinder Advanced Menu
Advanced menu page 2
PAGE2 (NEXTm$ PREVm4)
GAIN
mLOW :
MID :
HIGH : 18dB
HYPER: 36dB
DL : ON
EXIT MENU (YESmPUSH)
Item
GAIN
This sets gain values for the positions of the GAIN switch.
The HIGH, MID, and LOW values must be set so that LOW
< MID < HIGH.
LOW
Sets the L position.
MID
Sets the M position.
HIGH
Sets the H position.
HYPER
Sets the HYPER position.
DL
Sets DynaLatitude function
ON/OFF. This setting is
valid only when the
OUTPUT/DL/DCC+ switch
has been set to CAM/DL.
88
Chapter 4 Viewfinder Screen Indications and Menus
OdB
9dB
Settings
–3 dB, 0 dB (normal
value), 3 dB, 6 dB, 9 dB,
12 dB, 18 dB, 18 dB + DPR,
24 dB
0 dB, 3 dB, 6 dB, 9 dB
(normal value), 12 dB,
18 dB, 18 dB + DPR, 24 dB,
24 dB + DPR
3 dB, 6 dB, 9 dB, 12 dB,
18 dB (normal value),
18 dB + DPR, 24 dB, 24 dB
+ DPR, HYPER GAIN
36 dB (normal value),
42 dB
ON (normal value), OFF
When set to ON, the amount
of DynaLatitude effects is
set in the basic menu page 2
(see page 81). For details on
the DynaLatitude function,
see page 50.
Advanced menu page 3
PAGE3 (NEXTm$ PREVm4)
mAWB MEM
TONE
BARS
REMOTE1
REMOTE2
BAUD RATE: 38400
EXIT MENU (YESmPUSH)
a) For DSR-500WSPL: EBU75
Item Settings
AWB MEM 2 (normal value): No
Selects whether or not correspondence with FILTER
to make the FILTER control settings. Only two
control settings (1 to 4) adjustment values (A and B) are
correspond to stored in memory.
separate white 2
balance adjustment FILTER control settings. Each of
values stored in the four control settings can be
memory. used to set A and B adjustment
values, for a total of eight settings.
TONE ON (normal value): Outputs
Selects whether or not audio signal.
to output a 1-kHz OFF: Does not output audio
audio signal with the signal.
color bars when the
OUTPUT/DL/DCC+
has been set to
BARS.
BARS SMPTE (normal value for DSR-
Selects normal width 500WSL): Normal width
or narrower width for EBU75 (normal value for DSR-
color bars. 500WSPL): EBU 75%
EBU100 (for DSR-500WSPL):
EBU 100%
SPLIT (for DSR-500WSPL): Not
for normal operation
SNG: Narrower than normal (used
for satellite communications, etc.)
REMOTE1
REC (normal value): Specifies
Sets a function for
recording start/stop.
switch 1 of the RM-
MARK: Specifies a Mark IN/OUT
LG1 connected to the
point.
REMOTE connector 1.
CUE: Specifies a Cue point.
NG: Specifies NG/OK.
REMOTE2
REC: Specifies recording start/stop.
Sets a function for
MARK (normal value): Specifies
switch 2 of the RM-
a Mark IN/OUT point.
LG1 connected to the
CUE: Specifies a Cue point.
REMOTE connector 1.
NG: Specifies NG/OK.
BAUD RATE
9600, 38400 (normal value)
Sets a baud rate for a
computer connected
to the REMOTE
connector 2 (to be
supported in the future
version).
: 2
: ON
a)
: SMPTE
: REC
: MARK
4FL: Correspondence with