Page 2
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres. Pour toute réparation faire appel à une personne compétente uniquement. PXW-FS7/PXW-FS7K...
Page 3
Be sure to keep your PC used for service and checking of this 修理時に使用するパソコンは,ウィルス検出ソフトが常にアッ プデートを行っているパソコンを使用してください。もし,修 unit always updated with the latest version of your anti-virus software. In case a virus affected unit was found during service, 理を行うセット,もしくはパソコンがウィルスに感染している 事が判明した場合は,ソニーグループ内は社内技術相談窓口に, contact your Service Headquarters. 特約店様は特約店様専用電話窓口(修理窓口)にご相談くださ い。 PXW-FS7/PXW-FS7K...
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU PUBLISHED BY SONY.
FE PZ 28-135mm F4 G OSS F4 G OSS [About the service of this model] PXW-FS7K is commodity that packed the Solid-State Memory Camcorder and Interchangeable Lenses. Refer to each following service manual the Interchangeable Lens kit, when you repair. Model Lens...
Besides this manual, the following manuals are available. • Before Using this Unit (Supplied with this unit) • Operating Guide (CD-ROM)(Supplied with this unit) • Adjust Manual (Available on request) The adjustment software is necessary for adjustment and various checking of this unit for the service. PXW-FS7/PXW-FS7K...
Page 17
Front Assy Section-2....................4-29 PXW-FS7/PXW-FS7K...
When this error is not cleared, replace the RE-328 board and/or the AVP-25 board. E40-003 Error of battery authentication Use the Sony genuine battery. When this error is not cleared, replace the RE-328 board and/or the AVP-25 board. Continued Function of this code is not provided in this unit.
IC0100 on the DPR-365 board and IC0201 on the VIF-58 board or IC0100 on the DPR-365 board and the peripheral circuit may be faulty. IC0201 on the VIF-58 board Replace the faulty DPR-365 board and/or the VIF-58 board. Continued PXW-FS7/PXW-FS7K...
Page 27
Replace the DPR-365 board. E95-311 Operation fault of IC0100 on the IC0100 on the DPR-365 board or the peripheral circuit may be faulty. DPR-365 Replace the DPR-365 board. Continued Function of this code is not provided in this unit. PXW-FS7/PXW-FS7K...
Page 28
IC0100 on the DPR-365 board and IC0800 on the VIF-58 board or VIF-58 board the peripheral circuit may be faulty. Replace the faulty DPR-365 board and/or the VIF-58 board. Function of this code is not provided in this unit. PXW-FS7/PXW-FS7K...
• The proper way to disconnect a connector is to grab the connector instead of the wires. If you pull on the wires, they might be broken. • The proper way to connect a connector is to grab the connector instead of the wires. If you push on the wires, they might be broken. PXW-FS7/PXW-FS7K...
• KY-739 board ( Inside Panel Section-2) Refer to following items on the ADJUST tab of the Adjust Manual for destination data input, USB Serial number and Product ID input when replacing DPR-365 board. • DPR-365 board: Initialize Machine ID (DPR board) PXW-FS7/PXW-FS7K...
IC0201 (VIF-58 board) Version 3 IC3102 (AVP-25 board) – IC2803 (DPR-365 board) IC631 (KY-739 board) 2-4-3. Details of Each Menu Factory Reset Menu The Factory Reset menu is used to restore the factory settings (default settings) of the Service menu. PXW-FS7/PXW-FS7K...
Page 33
• IC0100 (DPR-365 board) version • IC1900 (DPR-365 board) version Version 2 Menu • IC1100 (DPR-365 board) version • IC0201 (VIF-58 board) version Version 3 Menu • IC3102 (AVP-25 board) version • IC2803 (DPR-365 board) version • IC631 (KY-739 board) version PXW-FS7/PXW-FS7K...
Measure the dimensions before replacement of the IM E Mount Base Block Assy according to procedures 1 to 3. Remove the Imager Block Assy and the IM Adjust Washers (A). IM Module Sub Block Assy IM Adjust Washers (A) PXW-FS7/PXW-FS7K...
Page 35
[B’] : Dimension of new IM Module Sub Block Assy Assemble the imager, using the selected IM Adjust Washers. After assembling is completed, perform the test shooting and confirm that no blur is observed in the peripheral area of shot. PXW-FS7/PXW-FS7K...
It is the software to adjust and check digital cameras and camcorders for service. The installer of the Adjust Manual and the installation manual are attached, be sure to confirm the contents of them. Note Be sure to install Adjust Station first. PXW-FS7/PXW-FS7K...
2-5. IM E マウントベース部組交換時の注意 以下の手順は 3 箇所それぞれ行ってください。 注意 IM E マウントベース部組の交換を行う前に、 手順(1)から(3)にて交換前の寸法を測定してください。 イメージャ Assy、 IM 調整ワッシャ (A) を取り外してください。 IMモジュールサブ部組 IM調整ワッシャ (A) PXW-FS7/PXW-FS7K...
Page 49
IM E マウントベース部組交換後の IM モジュールサブ部組の各 IM 調整ワッシャ取り付け部について も同様に寸法 [B'] を測定してください。 以下の式より新たに使用する IM 調整ワッシャの寸法 [A'] を算出し、 ワッシャの選定を行ってください。 新たに使用する IM 調整ワッシャの寸法 [A’] = ([A] + [B]) – [B’] [A] + [B] : 交換前の寸法 [B’] : 新 IM モジュールサブ部組の寸法 選定した IM 調整ワッシャを使用してイメージャを組み付けてください。 組立完成後、 試し撮りを行い周辺ボケ等の不具合が無いことを確認してください。 PXW-FS7/PXW-FS7K...
(Size: 28 x 9 mm) Be careful not to break the flexible board. #211 (Note) SP901 (Size: 15 x 8 mm) #119 #119 Inside Panel Section-1 #104 Disassembly Places [1] #104 X 2, {1} Coin Screw X 1 Bottom View #104 PXW-FS7/PXW-FS7K...
Page 58
[2] #119 X 4 Bottom View #119 #119 [3] #49 X 2 Bottom View [4] #49 X 3 → Open The Lid {4} → #49 X 2 Front View Bottom View Right View [5] #49 X 3 Right View PXW-FS7/PXW-FS7K...
Page 59
Notes on Assembling the Overall Section-2 Attaching the Bottom Cabinet Claws Bottom Cabinet PXW-FS7/PXW-FS7K...
(Size: 28 x 9 mm) (Size: 10 x 10 mm) #119 DV-36 BOARD Be careful not to break the flexible board. #119 Outside Assy Section #119 Be careful not to break (Note) (Size: L = 4 mm) the lead wires of MIC901. PXW-FS7/PXW-FS7K...
Page 61
[2] #49 X 1 → #49 X 3 → Open the Cover {2} → #49 X 2, #119 X 2 Front View Left View Rear View #119 [3] #49 X 1, #119 X 2 → #49 X 1 Left View Bottom View #119 PXW-FS7/PXW-FS7K...
Page 62
[4] #49 X 3 Left View [7] #105 X 2 Left View #105 [8] #49 X 2 Top View [10] #49 X 2 → #49 X 1 → #49 X 2 Front View Left View Bottom View 4-10 PXW-FS7/PXW-FS7K...
Page 63
Notes on Assembling the Overall Section-3 Routing the Harness Harness Arranging the Flexible Board Center Mountain fold Valley fold FP-220 Flexible board 4-11 PXW-FS7/PXW-FS7K...
4-2-5. Overall Section-5 • Refer to “Overall Section-5” on exploded view for Ref. No. Rear Assy Section (Note) (Size: 20 x 20 mm) #105 #105 (Note) #105 17.8 #105 #105 #105 15.7 (Note) (Size: 10 x 10 mm) 4-15 PXW-FS7/PXW-FS7K...
Page 68
Disassembly Places [1] #49 X 6 Bottom View [3] #49 X 4 → #105 X 3 Left View Right View #105 #105 [4] #105 X 1 Front View #105 [5] #105 X 1 Rear View #105 4-16 PXW-FS7/PXW-FS7K...
Page 69
[6] #49 X 2 → #49 X 1 Left View Front View Notes on Assembling the Overall Section-5 Arranging the Flexible Board FP-223 Flexible board FP-216 Flexible board FP-239 Flexible board Mountain fold Valley fold 4-17 PXW-FS7/PXW-FS7K...
Inside Panel Section-2 • Refer to “Inside Panel Section-2” on exploded view for Ref. No. #310 Notes on Assembling the inside panel-2 Installing the Magnet Install the magnet with the marking oriented as shown below. AU Base Marking 4-22 PXW-FS7/PXW-FS7K...
If the original state cannot be restored due to loss of the IM adjust washer, for example, replace the Mount Block Assy Service. IM調整ワッシャ(A)は, それぞれ厚さが異なります。 取り外したIM調整ワッシャは, 必ず元の位置に戻してください。 また, IM調整ワッシャを交換する際は, SELECTION PARTS を 参照してください。 IM adjust washerを紛失するなどして元の状態に戻せなくなっ た場合は, Mount Block Assy Service を交換してください。 4-27 PXW-FS7/PXW-FS7K...
Page 80
マウントブロックAssy サービスは構造上, 静電気により破壊さ れる恐れがあるため, MOS ICと同様に注意して取り扱ってくだ さい。 また, 受光部にはゴミの付着, および強い光がはいることのない ように注意してください。 Notes on Assembling the Front Assy Section-1 Putting position of the IM Adjust Washer (A) Adjust IM Washer (A) Adjust IM Washer (A) Adjust IM Washer (A) 4-28 PXW-FS7/PXW-FS7K...
Page 89
GASKET (5.5X5 (7)), SOFT M901 1-855-374-11 DC FAN 2-630-005-31 SCREW (M2), NEW TRUSTER, P2 #105 2-891-494-31 SCREW (M2), NEW TRUSTER, P2 #119 7-627-556-58 SCREW +P 2.6X5 Note Use this to cut or splice so that it becomes the designated size. 指定のサイズになるように形状を加工して使用してください。 PXW-FS7/PXW-FS7K...
4-546-921-01 WP SHEET (HP) Use this to cut or splice so that it becomes the designated size. 4-546-916-01 FAN HOLDER B 4-546-922-01 FH BARRIER SHEET 指定のサイズになるように形状を加工して使用してください。 4-546-925-01 CABLE CLAMPER 4-548-622-01 TAPE (HS16-010 (10X40)) (Note) 4-274-987-01 TAPE (AS 1/2) (C) PXW-FS7/PXW-FS7K...
Use this to cut or splice so that it becomes the designated size. 1-846-258-11 FLEXIBLE FLAT CABLE (FFC-1030) 指定のサイズになるように形状を加工して使用してください。 4-548-622-01 TAPE (HS16-010 (10X40)) (Note) 4-564-134-01 TAPE HS13-015(25X35) 4-546-922-01 FH BARRIER SHEET MIC901 1-542-979-11 MICROPHONE, ELECTRET CAP 2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 2-630-005-31 SCREW (M2), NEW TRUSTER, P2 5-14 PXW-FS7/PXW-FS7K...
HOLDER, EYE CUP X-2581-585-5 LOUPE ASSY, VF 3-878-208-11 EYE CUP 4-547-109-02 LENS,CLOSEUP 4-269-215-01 BASE (L), HINGE 4-269-216-01 BASE (R), HINGE X-2581-584-1 VF REAR ASSY 4-440-210-01 ROD (951), LCD HOOD LOCK X-2590-535-1 VF FRONT ASSY(T) 3-080-206-21 SCREW, TAPPING, P2 5-16 PXW-FS7/PXW-FS7K...
OLPF PACKING 2-635-562-11 SCREW (M1.7) 2-587-151-01 SCREW (M1.4), NEW TRUSTAR.P2 #105 2-891-494-31 SCREW (M2), NEW TRUSTER, P2 #198 4-186-545-01 SCREW, 0+Z M1.7 SG (SPIN) Note Use this to cut or splice so that it becomes the designated size. 指定のサイズになるように形状を加工して使用してください。 5-21 PXW-FS7/PXW-FS7K...
(KY-POWER) GAIN/ISO WHT BAL L - M - H B - A - PRESET PS-894 BOARD (SIDE A) PS-894 BOARD (SIDE B) SW-1660 BOARD DPR-365 BOARD CN1000 (Page 7-1) S2721 ON/OFF AVP-25 BOARD FP-221 FLEXIBLE BOARD CN2103 (Page 7-3) PXW-FS7/PXW-FS7K...
のないように注意してください。 • As the imager may be damaged by static electricity from its structure, handle it carefully like for the MOS IC. In addition, ensure that the receiver is not covered with dusts nor exposed to strong light. PXW-FS7/PXW-FS7K...
Page 243
R2500 Through the Harness (PM-KY734) VDR250 C2501 VDR251 VDR252 0.1u KY-734 BOARD XX MARK: NO MOUNT KY-735 CN2600 PM-26 SW_REVERSE1 R2601 (2/2) S2600 CN4101 Through the SW_REVERSE2 R2600 Harness VDR261 (PM-KY735) VDR260 KY-735 BOARD XX MARK: NO MOUNT 8-75 PXW-FS7/PXW-FS7K...
• As the imager may be damaged by static electricity from its structure, handle it carefully like for the MOS IC. In addition, ensure that the receiver is not covered with dusts nor exposed to strong light. PXW-FS7/PXW-FS7K...
― ― 2014.12 Revised-1 • Addition of PXW-FS7K. (A1 14-101) Refer to the "Model Information" for the information of a bundled product with PXW-FS7K. • Revision of ACCESSORIES. 2015.06 Revised-2 • Correction of "Replacement of Main Parts", (A2 15-047) "Repair Parts List", "Block Diagrams", "Frame Schematic Diagrams"...
Need help?
Do you have a question about the PXW-FS7K and is the answer not in the manual?
Questions and answers