Storage; Storage Safety; Preparing The Traction Unit; Preparing The Engine - Toro Reelmaster 5010-H Operator's Manual

the desired set of cutting units from O
O .
N
D. Press the left button to save the settings
and exit the Settings menu.
3. Make initial reel-to-bedknife adjustments
appropriate for backlapping on all cutting units
which are to be backlapped; refer to the cutting
unit Operator's Manual.
4. Start the engine and run at low idle speed.
DANGER
Changing the engine speed while
backlapping may cause the reels to stall.
• Never change the engine speed while
backlapping.
• Only backlap at idle engine speed.
5. With the Mow/Transport lever in the M
position, move the Enable/Disable switch to
the E position. Move the Lower Mow/Lift
NABLE
control forward to start the backlapping operation
on the designated reels.
6. Apply lapping compound with a long-handled
brush.
Important:
Never use a short-handled
brush.
7. If the reels stall or become erratic while
backlapping, select a higher reel speed setting
until the speed stabilizes, then return the reel
speed to your desired speed. This can be done
using the buttons on the InfoCenter.
8. To make an adjustment to the cutting units
while backlapping, turn the reels off by moving
the Lower Mow/Raise lever rearward; the
Enable/Disable switch to the D
and shut off the engine. After completing
adjustments, repeat steps through .
9. Repeat the procedure for all cutting units you
want to backlap.
10. When finished, turn off the backlap functions,
using the buttons in the InfoCenter, and wash all
lapping compound off the cutting units. Adjust
cutting unit reel to bedknife as needed. Adjust
the cutting unit reel speed to the desired mowing
setting.
Important:
If you do not return the backlap
function to the O
the cutting units do not raise or function
properly.
Note:
For a better cutting edge, run a file across
the front face of the bedknife after lapping. This
removes any burrs or rough edges that may
have built up on the cutting edge.
OW
position,
ISABLE
setting after backlapping,
FF

Storage

to
FF

Storage Safety

•
Shut off the engine, remove the key, wait for all
movement to stop before you leave the operator's
position. Allow the machine to cool before
adjusting, servicing, cleaning, or storing it.
•
Do not store the machine or fuel container where
there is an open flame, spark, or pilot light, such
as on a water heater or on other appliances.

Preparing the Traction Unit

1. Park the machine on a level surface, lower the
cutting units, engage the parking brake, shut off
the engine, and remove the key.
2. Thoroughly clean the traction unit, cutting units,
and the engine.
3. Check the tire pressure; refer to
Tire Pressure (page
4. Check all fasteners for looseness; tighten them
as necessary.
5. Grease or oil all grease fittings and pivot points.
Wipe up any excess lubricant.
6. Lightly sand and use touch-up paint on painted
areas that are scratched, chipped, or rusted.
Repair any dents in the metal body.
7. Service the battery and cables as follows; refer
to Electrical System Safety (page
A. Remove the battery terminals from the
battery posts.
B. Clean the battery, terminals, and posts with
a wire brush and baking-soda solution.
C. Coat the cable terminals and battery posts
with Grafo 112X skin-over grease (Toro Part
No. 505-47) or petroleum jelly to prevent
corrosion.
D. Slowly charge the battery every 60 days
for 24 hours to prevent lead sulfation of the
battery.

Preparing the Engine

1. Drain the engine oil from the oil pan and install
the drain plug.
2. Remove and discard the oil filter. Install a new
oil filter.
3. Fill the engine with specified motor oil.
4. Start the engine and run it at idle speed for
approximately 2 minutes.
54
Checking the
45).
43):