Table of Contents
Advertisement
CE marking, tests:
The product complies with the Medical Device Directive
93/42/EEC.
The products have been tested and comply with the requirements set
out in EN 12183, which includes ISO 8191-2.
Combination agreements exist, see www.etac.com.
Etac's wheelchairs have been tested in accordance with
ISO 7176-19. They have been crash-tested by the Technical Research
Institute of Sweden. Testing has been carried out
using restraining device UNWIN_WWR/ATF/K/R using a 3-point seat
belt 907523, Klippan Safety AB.
Service life:
The anticipated durability and service life of the main product is
at least five years when used as intended, and in accordance with
the safety instructions, reconditioning manual and maintenance
instructions available in the user manual. The main product comprises
the seat and back chassis. Other parts/accessories are managed in
accordance with the manual and reconditioning manual. The actual
service life may vary depending on how often and how intensively
the product is used, but is at most 10 years. If the product is
intended for use after the service life period specified by Etac, it is the
responsibility of the product owner to ensure product functionality in
General
Product maintenance should be adapted to use.
If there is a fault in your wheelchair, please contact your prescriber or
technical aids centre. A defective wheelchair must not be used.
If your chair needs reconditioning or repair, only original parts
from Etac or components with equal quality should be used.
Etac will not be held responsible for damage or injury caused
by use of non-original parts.
When necessary lubricate moving parts/joints with
bicycle oil or similar.
The product must be serviced by trained personnel only.
Washing the back support and seat
The back cover is made from two-ply polyester. It is removed
by unscrewing the end terminations on the back rail.
Then pull the cover upwards, remove the tension rods and
wash in accordance with the washing instructions on the label.
The covers for the seat and back cushion are removable and
must be washed in accordance with the washing instructions
on the label.
Rear wheel/castor
Spokes:
Loose spokes can lead to wheel wobble. Consult
a cycle dealer or technical aids centre if it is necessary
to adjust the spokes.
Wheel axles:
Clean the wheel axles from hair and dirt as necessary.
Ball bearings: Require no maintenance.
Handrims:
If a handrim is damaged in such a way that it
can cause hand injuries, it should be replaced.
Brakes
Heavy dirt can have a negative effect on the brake mechanism. In
the event of adjustments, see Section "Brakes, adjustment".
11. Tests and Guarantees
accordance with the manual and reconditioning instructions. If this
cannot be ensured then the product should be taken out of use.
The following methods of surface treatment have
been used:
Lacquered surfaces = Polyester powder coating or ED lacquer
Non-lacquered aluminium parts = Anodised coating
Non-lacquered steel surfaces = Galvanised
Warranty:
5-year guarantee against material and manufacturing defects.
For terms and conditions, see www.etac.com.
Special adaptations:
comprise everything that falls outside the instructions and settings
in the manual. Wheelchairs specially adapted by customers are not
eligible for Etac's CE marking. Etac's guarantee no longer applies. If
there are any doubts concerning the adaptation, please contact Etac
for advice.
If the wheelchair is used in combination with another product,
neither product may keep the CE marking unless a combination
agreement is in place. Please contact Etac for up-to-date information.
12. Service and maintenance
Washing the frame
It is important, both for the sake of hygiene and for the longevity
of the chair, that the wheelchair is kept clean. It is equipped with a
drainage hole which ensures that it is easy
to wash and dry.
Clean the frame with a non-abrasive cleaning agent with
a pH level between 5 and 9, or with a 70% disinfectant solution.
Rinse and dry.
Chair with electrical back and seat recline function
Electrical components conform with protection class IPX6, which
means the product may be cleaned with a brush and water.
Do not rinse electrical components with a pressure washer.
Maximum washing temperature 20°.
Do not use chemicals on electrical components.
The battery charger must not be connected.
Internal cables must be connected.
Retract the actuator to the innermost position to avoid degreasing of
the piston rod.
For washing in a cabinet washer-disinfector, all electrical components
must be disconnected. See separate service manual at www.etac.
com.
Storage
Wheelchairs that are not used must be stored indoors.
Touch-up paint
For minor scratches and paint damage, touch-up paint
is available.
Separation at source/Waste
The product should be sorted in accordance with national regula-
tions.
Batteries: hand in to battery recycling.
Motor and control box: hand in to electronics recycling.
51
Etac / Prio / www.etac.com
Advertisement
Table of Contents
