Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Uniwide UniServer 1522LV
Summary of Contents for Uniwide UniServer 1522LV
-
Page 2: Table Of Contents
Contents 1. Introduction..................... 2 1.1 System Feature ..........................3 1.1.1 Front View..........................3 1.1.2 Front Panel Controls and Indicators..................3 1.1.3 Rear View..........................4 1.1.4 Inner View..........................5 1.2 System Specifications ........................6 1.3 Mainboard Layout ..........................9 1.3.1 Block Diagram ........................9 1.3.2 Mainboard Layout ....................... 10 2. - Page 3 4.2 Jumper Setting ..........................46 4.2.1 Clear CMOS Jumper: JBAT1 ....................46 4.2.2 BIOS Recovery Jumper: J10 ....................46 4.2.3 BIOS Write Protect Jumper: J6 .................... 46 4.2.4 On-board VGA Enable/Disable Jumper: JVGAD..............47 5. Software & Utilities................48 5.1 NVRAID............................48 5.1.1 Basic Configuration Instruction ....................
- Page 4 NOTE: For any up-to-date version of this document, please see our web site at www.uniwide.com. UNIWIDE Technologies, Inc. reserves the right to make changes to the product described in this manual at any time and without notice. This product, including software, if any, and documentation may not, in whole or in part, be copied, photocopied, reproduced, translated or reduced to any medium or machine without written consent.
-
Page 5: Introduction
UniServer offers the best in class for each of these challenges by employing the latest technology designed by a specialized sever team. The UniServer 1522LV 1U Rackmount Server is a high-performance barebone system powered by dual AMD ®... -
Page 6: System Feature
1.1 System Feature 1.1.1 Front View a. Slim CD-ROM Drive d. Hard Disk Drives b. Front Panel Controls and Indicators e. Rack Mounting Bracket c. Front Bezel 1.1.2 Front Panel Controls and Indicators a. USB 2.0 Ports e. System Fault LED b. -
Page 7: Rear View
1.1.3 Rear View a. AC Power Inlet e. VGA Port b. USB 2.0 Ports GbE LAN Ports c. Serial Port g. PCI Slot d. PS/2 Port(Keyboard & Mouse) LAN Port Function The LAN port uses a CAT 6 LAN cable for connecting the motherboard to a local area network by means of a network hub. -
Page 8: Inner View
1.1.4 Inner View a. FAN Modules Heatsink b. Power Supply PCI-Express Slot c. CPU Air Duct Slim CD-ROM d. Memory DIMM Slots... -
Page 9: System Specifications
1.2 System Specifications Processor Dual socket F (1207pin) AMD Opteron Processors Supports up to 2P/8C Dual-Core/Quad-Core AMD Opteron 2000 Series processors Integrated 128bit DDR-2 memory controller Chipset NVIDIA nForce Professional 3400 ® Winbond Super I/O chip Memory 128-bit dual channel memory bus 4 DIMMs for CPU, up to 32GB memory capacity Registered ECC DDR2 400/533/667 SDRAM DIMM SATA Controller... - Page 10 Rear I/O One VGA port One serial port One PS/2 keyboard & mouse port Two USB 2.0 ports Two RJ45 GbE ports Front LED Panel Two USB 2.0 ports LEDs: Power / GbE LAN1 / GbE LAN2 / ID / System Fault Switches: System ID / Reset / Power System Management FAN connectors...
- Page 11 Power Supply 400W single power supply with PFC function AC Input: 100-240V~, 50/60Hz, 8-4A Form Factor 1U (H x W x D): 43.5 x 428 x 436.9 mm (1.7 x 16.85 x 17.2 inch)
-
Page 12: Mainboard Layout
1.3 Mainboard Layout 1.3.1 Block Diagram... -
Page 13: Mainboard Layout
1.3.2 Mainboard Layout ① DDR2 Memory DIMM Sockets ® ② AMD Opteron Socket 1207 - CPU ③ PCI Express x16 Slot ④ CD-ROM Connector ⑤ SATA Connectors ⑥ SATA Connectors ⑦ Fan Connectors ⑧ 24-Pin Power Connector ⑨ 8-Pin CPU Power Connector... -
Page 14: Important Safety
2. Important Safety Only a technically qualified person shall access, integrate, configure, and service this product. To avoid personal injury or property damage, read, observe, and adhere to all of the following safety instructions and information before you begin installing the product. 2.1 Intended Application Uses This product was evaluated as information technology equipment (ITE), which may be installed in offices, schools, computer rooms, and similar commercial type locations. -
Page 15: Earth-Grounded Socket Outlets
2.3 Earth-Grounded Socket Outlets CAUTION To avoid electrical shock, the system power cord(s) must be plugged into socket-outlet(s) that is provided with a suitable earth ground. The system will be provided with the following marking: Connect only to properly earthed socket outlet. 2.4 Before Removing the Access Covers CAUTION To avoid personal injury or property damage, the following safety instructions apply whenever accessing inside the... -
Page 16: Cooling And Airflow
Keep part of your body in contact with the metal server chassis to dissipate the static charge while handling the components. Avoid moving around unnecessarily. Hold the server components (especially boards) only by the edges. Place the server components on a grounded, static-free surface. Use a conductive foam pad if available but not the component wrapper. -
Page 17: System Installation
3.1 Preparing for Setup 3.1.1 Unpacking ① Main Box ② System Bottom Cushion ③ Heatsink Box ④ UniServer 1522LV Barebone System ⑤ System Top Cushion ⑥ Slide Rail ⑦ Accessory Box CAUTION In setting the product out of the box, hold it in the middle and not the cushion. -
Page 18: Packing List
3.1.2 Packing List Unpack the package and check if all items listed below are present. If any item contained in the package is damaged or missing, please contact your local dealer for replacement. In addition, keep the box and packing materials for possible future use. 1522LV Barebone Server Slide Rail CPU Heatsink... -
Page 19: Environmental Specifications
3.1.3 Environmental Specifications Place In front of the system, minimum 25" of the space is needed for using and managing the system. In rear of the system, minimum 30" of the space is needed for managing the system and airflow. Power supply Before installing the system, check the power capacity of the place where the system is installed. -
Page 20: Installing The Slide Rails Into The System
3.1.4 Installing the Slide Rails into the System This section provides information on installing the system into a rack unit with the slide rails provided. Slide Rail Attach slide rails on both left and right side of the system and secure them with 4 screws. Rear Rack Mounting Brackets As shown in the picture below, align rear rack mounting brackets with the rear frame of the cabinet. -
Page 21: Installing The System At The Rack Cabinet
3.1.5 Installing the System at the Rack Cabinet CAUTION Remove all the cables from system before installing. CAUTION System can be heavy. To reduce the risk of personal injury or damage to the equipment, get help to lift and stabilize the system during installation or removal, especially when the system is not fastened to the rails. -
Page 22: Installing User Serviceable Component
3.2 Installing User Serviceable Component 3.2.1 CPU System mainboard accommodates Socket-F (1207 pin) AMD Opteron Processors at 2000 MT (Mega Transfer per second). Follow these instructions to install the CPUs. ① Lift up the socket-locking lever slightly and remove away plastic cover. ②... -
Page 23: Memory
3.2.2 Memory The system mainboard uses Dual Inline Memory Modules (DIMM). The memory DIMMs accommodates Registered ECC (400/533/667) SDRAM DIMM and Double Data Rate Memory (DDR2) memory modules in 128MB, 256MB, 512MB, 1GB, and 2GB, 4GB combinations. Total memory size for CPU is up to 32GB. CAUTION The system mainboard has strict memory type and timing requirements. - Page 24 Memory Installation ① Locate the memory into the socket of the DIMM module ② Make sure the DIMM’s pins are facing down, and check that the pin arrangement on the memory module resembles the one pictured below. ③ Insert the module into the DIMM socket and press down evenly on both ends firmly until the DIMM module is securely in place.
-
Page 25: Hard Disk Drive
3.2.3 Hard Disk Drive NOTICE When you install hard disk drive into the system, we recommend using slot #0 first. HDD ID Configuration HDD Type Slot #0 Slot #1 SATA ID 0.0 ID 0.1... -
Page 26: Pci Add-On Card
3.2.4 PCI Add-on Card WARNING Power off power supply completely when adding or removing any expansion card and other system components. Failure to do so may cause severe damage to both your motherboard and expansion card. 3.2.4.1 PCI Add-on Card Installation ①... -
Page 27: Bios And Jumper Setting
4. BIOS and Jumper Setting 4.1 BIOS This chapter provides information on the BIOS Setup program and allows you to configure the system for optimum use. You may need to run the Setup program when: An error message appears on the screen during the system booting up, and requests you to run SETUP. You want to change the default settings for customized features. -
Page 28: Control Keys
4.1.2 Control Keys Function <F1> or <Alt-H> General Help window <Esc> Exit this menu ←→arrow keys Select a different menu ↑ or ↓ arrow keys Move cursor up and down <Home> or <End> Move cursor to top or bottom of window <PgUp>... -
Page 29: General Help
4.1.4 General Help <F1> The BIOS setup program provides a General Help screen. You can call up this screen from any menu by simply pressing <F1>. The Help screen lists the appropriate keys to use and the possible selections for the highlighted item. -
Page 30: Main Menu
Power Use this menu to specify your settings for power management. Exit This menu allows you to load the BIOS default values or factory default settings into the BIOS and exit the BIOS setup utility with or without changes. 4.1.6 Main Menu The items inside the Main menu are for basic system information and configuration. -
Page 31: Advanced Menu
System Memory, Extended Memory These items show the memory status of the system. (Read-only) System Time The time format is <HH> <MM> <SS>. System Date The date format is <MM> <DD> <YYYY>. 4.1.7 Advanced Menu Items in the menu are divided into several sub-menus. Each sub-menu provides more settings. To enter the sub-menu, highlight the sub-menu you want to configure and press <Enter>. - Page 32 Fan Type Control This setting allows you to select the fan type (3-pin or 4-pin) for fan power management. Select 3-pin for UniServer 1522LV system. IOMMU, Size AMD64, one of the 64-bit architectures, contains a device called the IOMMU (Input/Output Memory Management Unit).
- Page 33 CPU0/CPU1 Information This sub-menu shows the detail processor information. Memory Controller Options This setting is for setting Max Mem Clock and controller options. Max Mem Clock Use this field to configure the highest clock frequency of the installed DRAM. Users may also assign a lower memory clock frequency here.
- Page 34 Node Interleave AMD Opteron CPU supports a mode called node interleave. When node interleave is disabled, the memory controller maps the local memory of each processor to a single contiguous range of physical addresses. This allows the operating system to map user data to local memory, whenever possible, to allow programs to access data the most rapidly.
- Page 35 ECC Error Checking This setting enables/disables ECC (Error Correction Code) checking, a method of checking the integrity of data in DRAM. ECC provides more elaborate error detection than parity; ECC can detect multiple-bit errors and can locate and correct single-bit errors. ECC Error Log This setting logs the ECC error.
- Page 36 USB Control This setting enables/disables the onboard USB host controller. USB BIOS Legacy Support Set to [Enabled] if your need to use any USB 1.1/2.0 device in the operating system that does not support or have any USB 1.1/2.0 driver installed, such as DOS and SCO Unix. MAC LAN, MAC 1 LAN These settings allow you to enable/disable the specified device controllers.
- Page 37 IDE Configuration Large Disk Access Mode Defaulting this setting to [DOS] will create a Translated FDPT. Compatible ill-behaved applications will operate correctly when [DOS] is selected. Setting to [Other] will create a Standard FDPT. Incompatible ill-behaved applications will function correctly with [Other]. Local Bus IDE Adapter This setting controls the onboard IDE adapter.
- Page 38 Primary Master, Primary Slave Press PgUp/<+> or PgDn/<-> to select [Manual], [None] or [Auto] type. Note that the specifications of your drive must match with the drive table. [Type] The hard disk will not work properly if you enter improper information for this category.
- Page 39 I/O Device Configuration KBC Clock This BIOS feature allows you to adjust the keyboard interface clock for a better response or to fix a keyboard problem. It is recommended that you select a higher clock speed for a better keyboard response. But if the keyboard performs erratically or fails to initialize, try a lower clock speed.
- Page 40 IPMI IPMI Specification Version Indicate the IPMI (Intelligent Platform Management Interface) version. BMC Hardware/Firmware Version Indicate the BMC (Baseboard Management Controller) version. System Event Logging This function is used to log system events. Clear System Event Log This function is used to clear system event logs. Existing Event Log Number Indicates how many event logs are existing.
- Page 41 System Event Log This setting shows the real-time system event logs on the system monitor sensor. Dynamic or Static IP Config This setting is used to configure your dynamic (temporary) or static (permanent) network IP. Setting to [DHCP] (Dynamic Host Configuration Protocol) allows the network IP to be automatically assigned. (Optional) IP Address, IP Subnet Mask, Default Gateway Use these settings to set up the IP address, IP subnet mask, and default gateway for your system network.
- Page 42 Console Redirection Com Port Address This setting enables/disables the Com port address for console connection. Baud Rate This setting specifies the transfer rate (bits per second) of Console Redirection. Console Type This setting specifies the console type. Flow Control This feature allows you to enable flow control. Console Connection This feature indicates whether the console is connected directly to the system or a modem is used for connection.
- Page 43 DMI Event Logging Event Log Capacity/Validity These items indicate the status of Event log validity and capacity. View DMI Event Log Press [Enter] to view the contents of the DMI event log. Clear All DMI Event Logs When this setting is set to [Yes], the DMI event log will be cleared at next POST stage. Then, the BIOS will automatically set this option to [No].
-
Page 44: Security Menu
4.1.8 Security Menu This section lets you set security passwords to control access to the system at boot time and/or when entering the BIOS setup program. It also allows you to set virus protection at hard disk boot sector. Supervisor Password Is/ User Password Is It shows the preset supervisor/user password. -
Page 45: Boot Menu
4.1.9 Boot Menu Use this menu to arrange and specify the priority of the devices from which the BIOS will attempt to boot the Operating System. Boot Priority Order Item Specific Help This setting allows users to set the boot priority of the specified devices. Refer to the the right pane for instructions. -
Page 46: Power Menu
4.1.10 Power Menu Use this menu to specify your settings for Power Management. Remember that the options available depend upon the hardware installed in your system. Enable Cool’n’Quiet This feature is especially designed for AMD Athlon processor, which provides a CPU temperature detecting function to prevent your CPU from overheading due to heavy workload. - Page 47 ACPI Suspend Support This item specifies the power saving modes for ACPI function. If your operating system supports ACPI, you can choose to enter the Standby mode in S1 (POS) or S3 (STR) fashion through the setting of this field. Wake Up by LAN Select [Enabled] to wake up the system when incoming signals are detected on the specified LAN devices.
-
Page 48: Exit Menu
4.1.11 Exit Menu The following sections describe each of the options on this menu. Note that <Esc> does not exit this menu. You must select one of the items from the menu or menu bar to exit. Exit Saving Changes When you want to quit the Setup menu, you can select this option to save the changes and quit. -
Page 49: Jumper Setting
4.2 Jumper Setting 4.2.1 Clear CMOS Jumper: JBAT1 There is a CMOS RAM onboard that has a power supply from external battery to keep the data of system configuration. With the CMOS RAM, the system can automatically boot OS every time it is turned on. If you want to clear the system configuration, set this jumper to clear data. -
Page 50: On-Board Vga Enable/Disable Jumper: Jvgad
4.2.4 On-board VGA Enable/Disable Jumper: JVGAD This jumper is used to enable/disable the on-board VGA. When you want to use on-board VGA, short connect pin#1-2 of this jumper (Default option). If you want to use add-on VGA card and disable on-board VGA, short connecting pin#2-3 of this jumper. -
Page 51: Software & Utilities
5. Software & Utilities 5.1 NVRAID 5.1.1 Basic Configuration Instruction The following are the basic steps for configuring NVRAID 5.1.1.1 Non-Bootable RAID Array ① Choose the hard disks that are to be RAID enabled in the system BIOS. ② Specify the RAID level, either Mirroring (RAID 1), Striping (RAID 0), Striping and Mirroring (RAID 0+1), or Spanning (JBOD) and create the desired RAID array. -
Page 52: Setting Up The Bios
5.1.2 Setting up the BIOS Be sure to enable the “ VIDIA RAID Function in VIDIA RAID Setup of Integrated Peripherals” in BIOS before configuring the NVRAID BIOS. After that press F10 to save the configuration and exit. The server will reboot right away. -
Page 53: Entering The Raid Bios Setup Basic Configuration Instruction
5.1.3 Entering the RAID BIOS Setup Basic Configuration Instruction ① After rebooting your system, wait until you see the RAID software prompting you to press F10. The RAID prompt appears as part of the system POST and boot process prior to loading the OS. ②... - Page 54 In upper picture 1.0.M means the hard drive is attached to Adapter 1, Channel 0, and the drive is set to Master. The following is a list of all possible combinations: 1.0.M Adapter 1, Channel 0, Master 1.1.M Adapter 1, Channel 1, Master 1.2.M Adapter 1, Channel 2, Master Serial ATA...
- Page 55 NVIDIA RAID Utility – Array Disks 5.1.3.3 Completing the RAID BIOS Setup ① After assigning your RAID array disks, press F7. The Clear disk data prompt appears. ② Press Y to clear all drive data. The Array List screen appears, where you can review the RAID arrays that you have set up.
- Page 56 ③ Use the arrow keys to select the array that you want to set up, and then press Enter. The Array Detail screen appears. The Array Detail screen shows information about the array that you selected, such as Striping Block used, RAID Mode, Striping Width, Disk Model Name, and disk capacity.
-
Page 57: Nvidia Raid Utility Installation
5.1.4 NVIDIA RAID Utility Installation 5.1.4.1 Installing the NVIDIA RAID Driver Under Windows (For Non-bootable RAID Array) This section describes how to setup the application and install the RAID software which will upgrade the Windows IDE driver and install the RAID driver. ①... - Page 58 5.1.4.2 Installing the RAID Driver (For bootable RAID Array) ① After you complete the RAID BIOS setup, boot from the Windows CD, and the Windows Setup program starts. ② Press F6 and wait for the Windows Setup screen to appear. ③...
- Page 59 ④ Press Enter to continue with operating system Installation, Be sure to copy the files from the floppy is complete, then take out the floppy. ⑤ Following the instructions on how to install operating system, During the GUI portion of the installation you might be prompted to click Yes to install the RAID driver.
-
Page 60: Serverdome Overview
5.2 ServerDome Overview The ServerDome provides remote server management for the 1U, 2U, 3U UniServer. With comprehensive management capabilities from a single graphical console, ServerDome remote management software automates and simplifies IT and networking tasks, letting the system administrator deploy, configure, manage and maintain X number of servers. -
Page 61: Removing & Installing System Components
6. Removing & Installing System Components 6.1 Installing the CD-ROM Drive ① Screw two brackets and the interface board to the CD-ROM. ② Remove the blank CD-ROM. ③ Locate the CD-ROM kit right into the place on the chassis and then slide it forward. ④... -
Page 62: Installing The Hard Disk Drive
⑤ Install the FFC(Flexible Flat Cable) of CD-ROM drive. CAUTION Face the conduct side down and lock the connector to secure the cable. Do not treat the connector by force. 6.2 Installing the Hard Disk Drive ① Remove the blank disk from the disk carrier and secure HDD to the carrier with four screws. ②... -
Page 63: Installing Pci Riser Module
6.3 Installing PCI Riser Module ① Loosen the screw of the PCI lock bracket. PCI lock bracket ② Pull the PCI bracket to the right and backward. PCI bracket ③ Insert the express card into the riser card slot of the chassis. ④... -
Page 64: Replacing The Power Supply Unit
6.4 Replacing the Power Supply Unit CAUTION In removing the power supply, handle the heavy unit with care ① Remove away 3 mounting screws from rear and bottom side of the chassis. ② Pull out the both 24-pin and 8-pin CPU power cable from the system. ③... -
Page 65: Replacing The Cooling Fan Unit
6.5 Replacing the Cooling Fan Unit WARNING Do not remove the fan module while operating the system. In installing the fan module, carefully set the unit on the fan connector. ① Take out the cable duct and cut the cable tie for the cable alignment. ②... -
Page 66: Installing The Motherboard
6.6 Installing the Motherboard CAUTION In order to remove or install the motherboard, remove the power module, AC strip unit, PCI riser card unit, HDD Carrier, HDD LED Boards and Cooling FAN unit beforehand. ① Remove the power supply unit and HDD carriers away from the system beforehand. ②... -
Page 67: Installing The Cpu Heatsink
6.7 Installing the CPU Heatsink CAUTION Make sure that thermal interface material should be pasted on the bottom side of the heatsink. 6.8 Installing the Front Bezel ① Locate the front bezel on the chassis as shown below. ② Slide the bezel toward the left until it makes the click sound. ③... -
Page 68: Cable Routing
7. Cable Routing 7.1 Cable Routing Example UniServer 1522LV system has 4 cables for CPU Power, USB, front LED board and CD-ROM. This is the example of cable routing. a. Power Cables b. Front LED Cable c. FFC CD-ROM Cable...