1. Manuals
  2. Brands
  3. AEG Manuals
  4. Vacuum Cleaner
  5. VAMPYR Multi
  6. Operating instructions manual

AEG VAMPYR Multi Operating Instructions Manual

3 in 1 wet and spray vacuum cleaner
Hide thumbs
Table of Contents

Advertisement

Quick Links

VAMPYR
VAMPYR
Nass- und Sprühsauger
Wet and spray vacuum cleaner
Aspirateur par voie humide et pulvérisation
Zuigapparaat voor natzuigen en sproeizuigen
Gebrauchsanweisung
Operating instructions
Mode d'emploi
Gebruiksaanwijzing
Multi 3 in 1
®
Multi PRO 3 in 1
®

Advertisement

Table of Contents
loading

Related Manuals for AEG VAMPYR Multi

Summary of Contents for AEG VAMPYR Multi

  • Page 1 VAMPYR Multi 3 in 1 ® VAMPYR Multi PRO 3 in 1 ® Nass- und Sprühsauger Wet and spray vacuum cleaner Aspirateur par voie humide et pulvérisation Zuigapparaat voor natzuigen en sproeizuigen Gebrauchsanweisung Operating instructions Mode d’emploi Gebruiksaanwijzing...
  • Page 3 A = Motor head B = Rotary switch C = Rocker switch D = Quick disconnect coupler E = Hose connection F = Dust container G = Guide rolls H = Suspension pin / Stop position I = Vice action latch J = Cable K = Carry handle with cable cradle L = Suction tube or telescope tube, depending on design...

  • Page 4: Table Of Contents

    Contents Description of appliance ........33 Safety instructions .

  • Page 5: Safety Instructions

    – Wet vacuum cleaning – Spray vacuum cleaning The VAMPYR MULTI 3 in 1/MULTI Pro 3 in 1 is a multipurpose vacuum cleaner to be used for the dry vacuum cleaning of dust, sand, gravel, shavings and foliage; for the wet vacuum cleaning of liquids, blocked...
  • Page 6 • Avoid running over the cable with the appliance or the nozzle. This could damage the insulation. • Faulty cables can be replaced by the AEG Customer Service or an authorised workshop. • Repairs to electrical appliances may only be carried out by qualified service engineers.

  • Page 7: Readying The Appliance For Use

    This appliance conforms with the following EU Directives: • 73/23/EEC dated 19.02.1973 – Low Voltage Directive • 89/336/EEC dated 03.05.1989, (including Modification Directive 92/31/EEC) – EMC Directive. Readying the appliance for use Mounting the bottom rollers The bottom rollers are enclosed loosely for packaging-related reasons.

  • Page 8: Dry Vacuum Cleaning

    Dry vacuum cleaning Preparation Important: If the appliance has been used for wet vacuum cleaning beforehand it must be absolutely dry for this purpose; dry the hose and pipes beforehand if necessary. The motor protection filter must always be inserted into the suction hole. The thin hose attached to the motor head is required only for spray vacuum cleaning.
  • Page 9 Connecting the vacuuming hose and vacuuming pipes Insert the hose inserts into the suction hole as in the picture and turn it to the right until it locks into place. To remove the vacuuming hose, twist the hose inserts to the left and remove. At the other end of the vacuuming hose, first connect the vacuuming pipe without hook-in pins and then the one with pins;...
  • Page 10 Groove nozzle For vacuuming grooves, corners and narrow gaps. To ease comfort of use, the upholstery and groove nozzles can also be used with only one vacuuming pipe or can be connected directly to the handle of the vacuuming hose. Vacuuming brush For vacuuming furniture, PC keyboards etc.
  • Page 11 Regulating the suction power The suction power can be decreased by actuating the suction power regulator located on the handle, e.g. when vacuuming curtains. Slider for regulating the suction power – closed = full suction power – open = decreased suction power After dry vacuuming Turn the rotary switch to ”0”...

  • Page 12: Wet Vacuum Cleaning

    Wet vacuum cleaning Preparation Prior to wet vacuuming always ensure that the paper filter, the fine paper filter and the foam filter have been removed. The motor protection filter must always be inserted into the suction hole. The thin hose attached to the motor head is required only for spray vacuum cleaning.
  • Page 13 Connecting the vacuuming hose and vacuuming pipes Insert the hose inserts into the suction hole as in the picture and turn it to the right until it locks into place. To remove the vacuuming hose, twist the hose inserts to the left and remove. At the other end of the vacuuming hose, first connect the vacuuming pipe without hook-in pins and then the one with pins;...
  • Page 14 Without a nozzle Liquids can be directly vacuumed out of containers using the vacuuming hose, the vacuuming pipe or the groove nozzle. Remove these parts from the liquid prior to switching off the appliance to ensure that the vacuuming pipe is vacuumed clean. Exercise caution when vacuuming from containers e.g.
  • Page 15 Switching on the appliance Before commencing wet vacuuming always remove the paper filter and the foam filter. The rotary switch must be pointing to ”0”. The rocker switch must be pressed in the direction of the flooring nozzle symbol ” ”.

  • Page 16: Spray Vacuum Cleaning

    Only spray vacuum those surfaces and upholstery which are suitable to be wet vacuum cleaned. Do not wet fragile hand-woven carpets or carpets which are not colour-fast. Caution: When spray vacuum cleaning be sure to use only AEG detergent with foam inhibitor for spray vacuum appliances. Preparation:...
  • Page 17 Connecting the vacuuming hose, pressure hose and vacuuming pipes Insert the hose inserts into the suction hole as in the picture and turn it to the right until it locks into place. To remove the vacuuming hose, twist the hose inserts to the left and remove.
  • Page 18 Working with the nozzles when spray vacuuming The nozzles are all attached to the vacuuming pipe by pressing and twisting and are removed by pulling and twisting. Spray suction nozzle for carpet For using water when cleaning carpeting Attach the wide transparent nozzle to the end of the lower vacuuming pipe press the pressure hose attached to it into the clamping pieces located on the vacuuming pipes or secure the...
  • Page 19 Spray suction nozzle for upholstery For using water when cleaning upholstery, car seats etc. For better handling, the small transparent nozzle can be connected directly to the handle of the vacuuming hose: If necessary, unlock the pressure hose by turning it anti-clockwise and remove it if it is still connected to the shut-off valve.
  • Page 20 Switching on the appliance While spray vacuuming and afterwards the room should be well aired in order to facilitate rapid drying. The rocker switch must be pressed in the direction of the spray suction nozzle symbol ” ”. Plug the cable into the power outlet: To switch the appliance on, turn the rotary switch to the ”I”...
  • Page 21 Important: The carpet should not be walked upon while it is still damp. Caution: If the carpet has been shampooed at an earlier point in time, foam may collect in the dust container during cleaning and leak out of the air outlet. If this happens switch off the appliance and empty the dust container.
  • Page 22 Important: Each time after spray vacuum cleaning the vacuuming hose should be cleaned of particles of dirt and fluff if necessary. Dismantling the spray vacuuming components (Detach the spray suction nozzle’s pressure hose from the shut-off valve by turning the coupling piece anti-clockwise to unlock it.
  • Page 23 Maintenance Changing the filters The paper filter is to be changed if the efficiency of the vacuuming decreases or if the filter is very soiled: Hold the paper filter by the cardboard edge and firmly press it onto the suction hole. The paper filter must touch closely against the side of the dust container wall so that it is not damaged by the filter basket when gently...
  • Page 24 Cleaning the cables, pumps, valves and spray nozzles For practical reasons this cleaning is carried out directly after the appliance has been used for spray vacuuming. Pour approx. 2 litres of water into the detergent tank, place this into the dust container and attach the motor head. Plug the cable into the power outlet: Hold the nozzle over a drain, press the rocker switch in the direction of the spray suction nozzle symbol ”...
  • Page 25 ...dust escapes when vacuuming? • Are the paper filter and foam filter undamaged and correctly attached? • Has an AEG paper filter been used? ...the suction power gradually decreases? • Is the paper filter full? • Are the filter pores blocked by fine dust or grime? •...

  • Page 26: Replacement Parts

    So that your appliance always functions properly, we recommend that you use original AEG replacement filters and detergent concentrate. The original AEG replacement filters and the detergent concentrate can be obtained from your specialist dealer or from Customer Service. Foam filter ET no.
  • Page 27 Motor protection filter ET no. 668 900 895 Original AEG detergent concentrate 1 bottle containing 100ml ET no. 668 900 822...

  • Page 28: Special Accessories

    Longlife wet and dry filters ET no. 668 900 827 Professional set Ø 50 mm Vacuum system for coarse dirt Individual components can be obtained from AEG Customer Service. Pipe reducer 50 mm – 32 mm Ø Ø Connecting piece for professional system and...
  • Page 29 Wet and dry multi-purpose nozzle ET no. 668 900 830 evelled pipe nozzle ET no. 668 900 828...
  • Page 32 AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg.hausgeraete.de © Copyright by AEG 822 949 252 – 0503...

This manual is also suitable for:

Vampyr multi pro

Table of Contents