Download
Share
Print this page
  1. Manuals
  2. Brands
  3. RH Baby&child Manuals
  4. Indoor Furnishing
  5. MARCELINE TWIN OVER
  6. Instructions manual

RH Baby&child MARCELINE TWIN OVER Instructions Manual

Twin bunk bed inst
Hide thumbs

Advertisement

Quick Links

Download this manual
Distributed in the U.S.A by:
Restoration Hardware Baby & Child
11640 Harrel St. Suite B
Mira Loma, California 91752
rhbabyandchild.com
Distributed in Canada by:
Restoration Hardware Canada Inc.
1500-1055 West Georgia Street,
Vancouver, British Columbia V6E 4N7
WARNING: Read all
instructions before assembling this
product. KEEP INSTRUCTIONS
FOR FUTURE USE
CUSTOMER SERVICE
If you are missing parts or have any questions about this product, contact us first. You can also order parts by writing
to the address above .Include the product model number, color, and a brief description of the part. Call
1-800-762-1751.
CARE AND CLEANING
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning. Clean with mild soap on soft rag.
Rinse and dry thoroughly. If the bunk bed is to be stored, store in a cool dry place and carefully package all original
hardware to protect from loss.
TOOLS AND INSTALLATION
Tools Necessary: Allen Wrench (included).
Phillips screw driver (not included).
NOTE: When inserting bolts, turn clockwise until tight. Then loosen 1/2-3/4 of a turn. After crib is completely
assembled, return to each bolt and tighten.
Page 1 of 10

Advertisement

loading
Need help?

Need help?

Do you have a question about the MARCELINE TWIN OVER and is the answer not in the manual?

Questions and answers

Related Manuals for RH Baby&child MARCELINE TWIN OVER

Summary of Contents for RH Baby&child MARCELINE TWIN OVER

  • Page 1 Distributed in the U.S.A by: Restoration Hardware Baby & Child 11640 Harrel St. Suite B Mira Loma, California 91752 rhbabyandchild.com Distributed in Canada by: Restoration Hardware Canada Inc. 1500-1055 West Georgia Street, Vancouver, British Columbia V6E 4N7 WARNING: Read all instructions before assembling this product.
  • Page 2 IMPORTANT SAFETY INFORMATION FOR BUNK BED Follow the information on the WARNINGS appearing on the upper bunk end structure and on the carton. Always use the specified size mattress or mattress support, or both to help prevent the likelihood of entrapment or falls. Surface of mattress must be at least 5 inches below the upper edge of guardrails on top bunk.
  • Page 3 COMPONENT IDENTIFICATIONS AND HARDWARE COMPONENTS LOWER END PANELS 2 PCS LOWER SIDE RAIL 2 PCS SLAT ROLL 1 SET UPPER END PANELS 2 PCS UPPER END RAILS 2 PCS SLAT SUPPORT 3 PCS GUARD RAIL (BACK) 2 PCS GUARD RAIL (FRONT) 1 PC LADDER 1 PC...
  • Page 4 ASSEMBLY INSTRUCTIONS: STEP #1. LOWER BUNK BED ASSEMBLY. STEP #2. INSTALLATION OF LOWER BUNK BED SLAT ROLL. STEP #3. UPPER BUNK BED ASSEMBLY. STEP #4. SLAT SUPPORT INSTALLATION TO UPPER SIDE RAILS. STEP #5. ATTACH TWIN PANELS TO SLATS SUPPORT AND SIDE RAILS . STEP #6.
  • Page 5 STEP #2. INSTALLATION OF LOWER BUNK FIGURE 02 BED SLAT ROLL STEP #2.1 On the ends of the slat roll (C) are pre-bored screw holes (5). Set the slat roll into the cleats of the side rails (B) and secure the slats roll (C) with Phillips screws (5) provided.
  • Page 6 STEP #4. SLAT SUPPORT INSTALLATION TO UPPER SIDE RAILS FIGURE 04 STEP #4.1 On inside surface of the side rails (E) are cavities designed to hold the slat supports (F). Attach the slat supports (F) to both side rails (E) and secure with screws (6) provided.
  • Page 7 STEP# 6. INSTALLATION OF FRONT AND BACK GUARD RAILS TO UPPER BUNK BED. FIGURE 06-A STEP #6.1 On inside surface of both front and back guard rail (G, H) are pre-installed metal brackets, designed to attached to the side rails (E) of the upper bunk. Install the front and the back guard rail (G, H) on the upper bank by screwing (7) the metal brackets into the side rails (E) (refer FIGURE 06-A).

  • Page 8: Step #8. Ladder Assembly

    STEP #7. BUNK BED ASSEMBLY FIGURE 07 - A FIGURE 07 - B STEP #7.1 On top surface of lower end panels (A) are holes for steel dowels (9) that correspond to the holes in the leg of the upper bed (D). Insert steel dowels (9) on top of lower end panels (A) as in FIGURE 07-A.
  • Page 9 STEP # 9. METAL BRACKET INSTALLATION STEP # 9.1 After assembling the bunk bed, secure Guard Rails (H & I) to upper side rails (E) with metal plates (8) provided as in FIGURE 9. STEP # 9.2 After assembly slide the optional trundle(sold separately) (K) underneath the bunk bed as in FIGURE 10.
  • Page 10 STEP #10. TWIN BED ASSEMBLY - TO ASSEMBLE BUNK AS TWO TWIN BEDS STEP #10.1 Repeat step #1 to step #5, lower bunk bed assembly and upper bunk bed FIGURE 11 assembly. Note: in order to set up as two identical twin beds, one Lower End Panel (A) may be removed and exchanged with one Upper End Panel (D), so each bed has a headboard (Lower End Panel-A) and foot board (Upper End Panel-D).