Table of Contents
Advertisement
2.1 Power Specifications
AC Powered Units
Power Supply
Max. allowable momentary power failure
Fuse (size) rating
In-rush current
Power Consumption *1
*1 Includes the input current (7 or 5 mA per point)
DC Powered Units
Power Supply
Max. allowable momentary power failure
Fuse (size) rating
In-rush current
Power Consumption
2.2 Input Specifications
Input voltage
Input current
Input switching current
Response time
Variable response time
Circuit isolation
Operation indication
2.3 Output Specifications
Description
Switched voltages (resistive load)
Rated current / N points
(resistive load)
Max. Inductive load
Max. lamp load (tungsten load)
Minimum load
!
OFF
Response
time (approx.)
!
ON
Circuit isolation
Open circuit current leakage
Operation indication
3. Installation Notes
The installation of FX
products or associated products concern is felt, please contact a professional electrician who is trained to
the local and national standards applicable to the installation site.
FX
Main PLC units can be either directly or DIN rail mounted. For details of either method, and
1N
installation guidelines please refer to the FX
Mounting Cautions
• Units should not be installed in areas subject to the following conditions: excessive or con-
ductive dust, corrosive or flammable gas, moisture or rain, excessive heat, regular impact
shocks or excessive vibration.
• Take special care not to allow debris to fall inside the unit during installation e.g. cut wires,
shavings etc. Once installation is complete remove the protective paper band, to prevent
overheating.
OFF ! ON
ON ! OFF
Relay Output
≤ 240V AC, ≤ 30V DC
2A/1 point, 8A/COM
80VA, 120/240V AC
100W (1.17A/85V AC, 0.4A/
250V AC)
When supply voltage < 5V
DC allow at least 2mA flow
ON
OFF
By Relay
products has been designed to be safe and easy. If during the installation of these
1N
FX
-24M
1N
100-240V AC +10% -15%, 50-60 Hz
10ms; If less than 10ms, PLC continues operation
250V 1A
100V AC - Max. 30A for 5ms
200V AC - Max. 50A for 5ms
30W
FX
-24M
1N
24V DC + 20% - 12V DC -15% (28.8 ~ 10.2 V DC)
5ms; If less than 5ms, PLC continues operation
24V DC - Max. 25A for 1ms
12V DC - Max. 22A for 0.3ms
15W
FX
Main unit
1N
X0 ! ! ! ! X7
24V DC, 7mA
24V DC, 5mA
>4.5mA
0-15ms
10ms
10ms
----------------
LED is lit when coil is energized
HANDY MANUAL JY992D87501 (JAPANESE ONLY).
1N
FX
-40M
1N
250V 3.15A (3A)
32W
FX
-40M
1N
125V 3.15A (3A)
18W
FX
0N
X10 ! ! ! ! ∞
24V DC ±10%
>3.5mA
<1.5mA
10ms
---
Photocoupler
LED is lit
Transistor Output
5-30V DC
0.5A/1 point, 0.8A/COM
12W/24V DC
1.5W/24V DC
------------------
< 0.2ms; < 5µs (Y0,Y1 only)
< 0.2ms (I > 0.2A); <5µs (Y0,Y1 only)
PhotoCoupler
0.1mA/30V DC
FX
-60M
1N
35W
FX
-60M
1N
20W
, FX
Extension
2N
block
24V DC, 5mA
>3.5mA
Hide quick links:
Advertisement
Table of Contents
