Related Manuals for Siemens Cerban Splitter CBS-3
Summary of Contents for Siemens Cerban Splitter CBS-3
- Page 1 Manual LMSmodular Hardware Section 2 ® Cerberus LMSmodular Cerban Splitter CBS-3 Technical Manual Cerberus Security Siemens Building Technologies for People Cerberus Division and Assets...
- Page 2 Data and design subject to change without notice. / Supply subject to availability. © Copyright by Siemens Building Technologies AG We reserve all rights in this document and in the subject thereof. By accep- tance of the document the recipient...
-
Page 3: Table Of Contents
Inside the CS4................7 Inside the CS11 ................8 Power supply .................. 8 Cables and connections..............9 Connection to GW-20 ..............9 Connection to GW-21 ..............9 Connection to an user-provided device..........10 Baud rates..................10 Dip-switches description ..............11 Siemens Building Technologies 06.2000 Cerberus Division... -
Page 5: Introduction
Introduction The Cerban Splitter CBS-3 accepts in input a serial line on which data are transmitted using Cerban protocol and outputs the signal to two serial lines with the same protocol. The Cerban Splitter CBS-3 is composed by one CPU board to which is connected an asynchronous board with four communication lines. -
Page 6: Product Description
Product description The CPU board The CPU board (Fig. 1) is the only board that composes the Cerban Splitter CBS-3. service pin LED Neuron Reset Chip Flash EPROM Service Diagnostic UART UART1 UART2 UART3 UART UART4 Fig. 1 The CPU board On this board there are: §... -
Page 7: The Connection Board
In the lower right corner of the connection board there is the power supply block with two pins marked + and -. You must connect here the voltage source (10 to 30 V d.c.). Fig. 2 The connection board Siemens Building Technologies e1148c Cerberus Division... -
Page 8: The Network Configuration Of Cbs-3
The network configuration of CBS-3 The Cerban Splitter CBS-3 is inserted in the network configuration shown in Fig. 2.4. It allows to connect any device which uses the Cerban protocol to two independent serial lines. The two lines can be connected to any device able to understand the Cerban protocol. -
Page 9: Cpu Board Configuration
CBS-3. For instance, a CS11 requires the (OFF, OFF, ON) setting. Then, using the Tab. 3 , find out the dip-switches that are used by the UART to which the subsystem is connected; set the three dip-switches as specified. Siemens Building Technologies e1148c Cerberus Division 06.2000... -
Page 10: Cerban Vitality Telegram
Even if the Flash EPROM configuration is enabled, you must set the communication baud rate with subsystems using the dip-switches and according to the suggested pro- tocol/baud rates (See section 6). Siemens Building Technologies e1148c Cerberus Division 06.2000... -
Page 11: Hardware Installation
You need: § 2 plastic spacers § 2 self-tapping screws § 4 metal spacers § 2 short screws § 2 long screws § 2 board supports Fig. 4 Inside the CS4 Siemens Building Technologies e1148c Cerberus Division 06.2000... -
Page 12: Inside The Cs11
The gateway GW-21 is powered using the connector located on the connection board (Please refer to Fig. 2). Please pay attention to pin polarities. The supply voltage must be in the range 10 to 30 V d.c. Siemens Building Technologies e1148c Cerberus Division... -
Page 13: Cables And Connections
Cables and connections Connection to GW-20 The figure below shows how to connect the Cerban Splitter CBS-3 to the Gat eway GW- 20, to transmit messages to the CMS/LMS monitoring system. Only UARTs 3 and 4 can be connected to the Gateway. -
Page 14: Connection To An User-Provided Device
The following baud rates apply to the subsystems connected either to the CPU or the expansion board. BAUD RATE UART Spare 9600 4800 2400 1200 S1.7 S1.8 S2.1 S2.5 S2.6 S2.7 S3.3 S3.4 S3.5 S4.2 S4.3 S4.4 Tab. 5 Dip-switch settings for baud rate Siemens Building Technologies e1148c Cerberus Division 06.2000... -
Page 15: Dip-Switches Description
UART 4 BAUD RATE UART Spare 9600 4800 2400 1200 Subsystem Dip-switches S1.7 S1.8 S1.9 no subsystem S2.5 CS11/CZ10 S2.6 CS4/CZ12 S2.7 S3.3 S3.4 S3.5 S4.2 S4.3 S4.4 Fig. 9 Dip-switches description Siemens Building Technologies e1148c Cerberus Division 06.2000... - Page 17 Message traffic 6 CS11 1, 4, 5, 6, 8 CS4 6, 7, 8 CZ10 1, 6, 8 CZ12 1, 6 Power supply 8 Dip-switch 6 Subsystem setting 5 EPROM 5 Traffic 6 Flash EPROM 5, 6 Siemens Building Technologies 06.2000 Cerberus Division...
- Page 18 Siemens Building Technologies AG Cerberus Division CH-8708 Männedorf Alte Landstrasse 411 Cerberus Security Tel. +41 1 - 922 61 11 for People Fax +41 1 - 922 64 50 and Assets www.cerberus.ch Siemens Building Technologies Replaces e1148b Doc.no e1148c Cerberus Division Edition: 06.2000...