CONTENTS 1. INTRODUCTION Areas of use/indications for Netti II 1.2 Contra indications 1.3 Quality and durability 1.4 Environment and disposal 1.5 Information for re-use 1.6 About this manual 1.7 Vital measurements 2. QUICK REFERENCE 3. DESCRIPTION 4. FEATURES OF NETTI II 5.
Page 3
10.3 Long term storing 11. TROUBLESHOOTING 12. TESTS AND WARRANTY 12.1 Tests 12.2 Guarantee 12.3 Claim 12.4 Netti Customized / Individual adaptations 12.5 Combination with other products 12.6 Service and repair 13. MEASUREMENTS AND WEIGHTS Model: Netti II My-Netti.com Language: English Version: 2018-11...
1. INTRODUCTION Netti II is an all round comfort wheelchair meant for both indoor and outdoor use. It is tested to DIN EN 12183:2014. The tests were carried out by TÜV SÜD Product Service GmbH in Germany In Alu Rehab we believe that wheelchairs...
European disabilities may have multiple causes. Netti Standard DIN EN 12183:2014. II has an adjustable seat and back angle, As manufacturer, Alu Rehab A.S evaluates thus facilitating for the user change of the test to be equal to 5-6 years of normal position, mobilisation or posture correction use of the chair.
1.6 ABOUT THIS MANUAL RE-USE In order to avoid damages while using the Netti II wheelchair, please read this manual All products from Alu Rehab are designed carefully before starting to use the chair. to give years of maintenance-free service.
1.7 VITAL MEASURES Specifications Min. Max. Overall length with leg 1100 mm 1100mm Netti II is a all-round comfort wheelchair supports designed for both outdoor and indoor Overall width 590 mm 740 mm use. Min. dimensions in table refer to seat...
The content of this page is a summary of the Salt water can increase risk of whole manual. It gives a brief introduction to corrosion. Further precautions related the use and care of the Netti II wheelchair. to environmental conditions not needed. The quick reference is not a replacement for the manual, only a reminder/check list.
18. Angle adjustment wheel for leg support. * Be aware that specifications may vary between countries. If any of these parts are missing, please contact your dealer. For complete information, please contact your dealer. Model: Netti II My-Netti.com Language: English Version: 2018-11...
4. FEATURES OF NETTI II STANDARD ACCESSORIES SEAT SEAT • Seat cushion has to be ordered separately • Sliding seat (See chapter 5) • Tilt -9° til +16° • Adjustable height 400 mm to 470 mm by TABLE change of wheels •...
The tray replaces the existing standard armrest. Foot box info@solidworks.com Upholstered Wedge Increases side support. Lumbar support Amputation support Increases lumbar curvature. Brake extender 90 mm Foot plate 120 mm upholstery 250 mm Model: Netti II My-Netti.com Language: English Version: 2018-11...
Page 12
120 mm extender. To be used together Support B Small with 600 mm back rest cushion. When using Netti III with seat width 500 mm and more as Support C Large seat in car, the back rest extender and enforced head support is required.
Page 13
The user doesn’t have to leg supports, lift the legs when separate or complete. mounting or dis- Please study order mounting the leg form at My-Netti.com for detailed supports. information. Foot board with lock Frame extender The leg supports can Increases distance...
5.1 MOUNTING OF HIP BELT Drive wheels available in sizes: 12”, 16”, 20”, 22”, 24” Please see www.My-Netti.com for & 26”. All wheels continuously updated overview of belts and available 2 widths: 1” harnesses and installation instructions. and 1 3/8”. Puncture proof Flexel or PU or •...
Tilt actuator: 1650 gram Leg support actuator: 984 gram COMPONENTS each Netti II is available with electrical operation Hand control: 240 gram of tilt and leg supports. Functions can be Cable for charger: 20 gram mounted one by one, or all together, and are operated with a hand control.
Check angle of castor When seating and wheel adjustments are bearing house. (See done in the possible positions by standard equipment, the adjustments will not exceed chapter 6.5). safe limits. Model: Netti II My-Netti.com Language: English Version: 2018-11...
- unfix the wheel and replace it in the required The risk for tipping increases when the position in the front fork. drive wheel is moved forward in the drive wheel bracket. Model: Netti II My-Netti.com Language: English Version: 2018-11...
6 mm Allan key 13 mm open end spanner When using the comfort seat plate it is recommended to change seat plate when changing seat depth. The seat plate comes in depth: 400 mm, 430 mm & 460 mm.. Model: Netti II My-Netti.com Language: English Version: 2018-11...
If the anti-tip is positioned on the outside of the main wheel radius, it will interfere with curbs and stairs. The anti-tip should always be used for the safety of the user. Model: Netti II My-Netti.com Language: English Version: 2018-11...
• Tighten the straps so that they follow the curvature of the spine and gives a little extra support at the top of the sacrum. Model: Netti II My-Netti.com Language: English Version: 2018-11...
6.14 LEG SUPPORTS Height / length adjustment: The foot plates can be Netti II is as a standard equipped with steppless height adjusted. Universal leg supports. Angle adjustable • Loosen the screw on the leg supports can also be ordered. Both are side.
Page 22
Find the required position and refix it (B) 13 mm open-end spanner Never lift the wheelchair by the leg supports. 5 mm Allan key Model: Netti II My-Netti.com Language: English Version: 2018-11...
• Adjust the head support and fix it in required position. If the head support seems to short in height, it can be turned 180° by releasing the adjustment wheel at the rear of the horizontal bar (B) Model: Netti II My-Netti.com Language: English Version: 2018-11...
The brakes are constructed as parking brakes and shall not be used as driving brakes. Be aware of potential squeeze hazard between brake and tyre. Model: Netti II My-Netti.com Language: English Version: 2018-11...
Page 25
Do not leave the user in the wheelchair without activating the parking brake. 1 pc 10 mm open-end spanner. To ensure the correct functions of the wire, these must never be taut. Model: Netti II My-Netti.com Language: English Version: 2018-11...
7.2 BACKREST ANGLE Tilting the seating unit of the wheelchair is mostly used to give the user varying sitting The backrest angle for Netti II is adjusted to positions and preventing sliding, shearing one of the following 3 positions: and thereby pressure sores.
FINISH WEIGHT 61671.78 g SCALE 1:15 REPLACED FOR REPLACED BY This drawing is Alu Rehab A.S property and should not be copied or delivered to other firms or agents without our permission. Model: Netti II My-Netti.com Language: English Version: 2018-11...
0,5 l gas space capacity. The total unfolded chair width of c) Each article is made of material that will Netti II with seat width 500 mm is bigger not fragment. than 700 mm as specified in PRM-TSI. This may limit the possibilities for transport by d) Each article was manufactured in ac- railway and other public transport.
EMERGENCY EXIT The total chair width of Netti II with seate width 500 mm is bigger than 700 mm, it may therfore have difficulties passing through emergency escape exits.
• Drive carefully down the step and move the wheelchair backwards on the main wheel until the front castors have come away from the step. • Put the front castors down on the ground. Turn the anti tip down. Model: Netti II My-Netti.com Language: English Version: 2018-11...
Do not lift the wheelchair holding onto the leg,- arm or head supports. They may detach, the wheelchair may fall and the user may get hurt and the wheelchair damaged. Turn the anti tip down. Model: Netti II My-Netti.com Language: English Version: 2018-11...
The point of balance can also be changed by adjusting the seat angle and/or angle of backrest. It is recommended to use the anti tip. Check that the main wheel and quick release are locked properly. (Chapt 6.2) Model: Netti II My-Netti.com Language: English Version: 2018-11...
9.9 LIFTING THE 9.11 PUSH RIM WHEELCHAIR Netti wheelchairs are delivered with aluminium push rims as standard. The material and distance to the main wheel influences the ability of the user to grip. Contact your dealer to get information about push rims that fit your chair.
1. Remove cushions before washing the wheelchair. 2. Clean cushions and covers according to The Netti chairs are built of modules. Alu instructions printed on cushions. Rehab carries stock of all parts and is ready to supply these on short notice.
When in need of spare parts, please contact your dealer. When making changes affecting frame construction, contact dealer / manufacturer for confirmation before you start. Model: Netti II My-Netti.com Language: English Version: 2018-11...
12.1 TESTS • Claims are to be forwarded as soon as a defect is discovered and not later than 2 Netti II is tested and has been approved weeks after the defect is discovered. for usage both indoors and outdoors.
If any uncertainty about special fitting and Substitutions or alterations of components adaptations, please contact Alu Rehab from third part suppliers to Netti II requires A.S. the risk evaluation and acceptance of the product responsibility and safety for use of...
Max user weight is 125 kg. When mounting accessories such as power kit etc. the weight of the accessories must be subtracted from the max user weight. Dealer: Frame number.: Date: Stamp: Model: Netti II My-Netti.com Language: English Version: 2018-11...
Page 39
Model: Netti II My-Netti.com Language: English Version: 2018-11...
Page 40
MANUFACTURER: DISTRIBUTION EU: Alu Rehab ApS Alu Rehab AS Kløftehøj 8 Bedriftsvegen 23 DK-8680 Ry 4353 Klepp Stasjon NORWAY T: +45 87 88 73 00 F: +45 87 88 73 19 T: +47 51 78 62 20 info@My-Netti.com post@My-Netti.com My-Netti.com...
Need help?
Do you have a question about the II and is the answer not in the manual?
Questions and answers