LG AR-DR11-08A Installation And Operation Manual page 105

Table 64: LonTalk Points List.
Access NV Name
Read-Only Points, continued.
nvo DigStatus.bit09
nvo DigStatus.bit10
nvo DigStatus.bit11
nvo DigStatus.bit12
nvo DigStatus.bit13
nvo DigStatus.bit14
nvo DigStatus.bit15
nvo GlobalAlarm
nvo ActTmpSpt
nvo CirA_SatDschT
nvo CirB_SatDschT
nvo ColdCoil1Temp
nvo EntWterTempA
nvo EntWterTempB
nvo ExhaustTemp
nvo LeavWterTempA
nvo LeavWterTempB
nvo MixedTemp
nvo OutsideTemp
nvo SpaceTemp
nvo SupplyTemp
Write-Only Points
nvi EconEnthTrig
nvi ExhCFMSetpt
nvi OACFMSetpt
nvi SupCFMSetpt
nvi DehumSetpt
nvi OADMinSetpt
nvi UnocRHSetpt
nvi SpaceCO2Setpt
nvi SpacePressSpt
nvi SupPressSetpt
nvi OccUnocc
nvi ResetAlarms
nvi SystemEnable
nvi TempDeadband
nvi EconTempTrig
nvi IADewptTrig
nvi TempSetpt
nvi UnocCoolSetpt
nvi UnocHeatSetpt
SNVT Type
state.bit09
state.bit10
state.bit11
state.bit12 PreHeat Enable Digital Output
state.bit13 Reversing Valve Digital Output
state.bit14
Damper Status (OAD or RAD indicating a path of
state.bit15
switch (95)
temp_p (105) Active Temperature Set-point
temp_p (105) Circuit A Saturated Discharge Temperature
temp_p (105) Circuit B Saturated Discharge Temperature
temp_p (105)
temp_p (105) Leaving Water Temperature Circuit A
temp_p (105) Leaving Water Temperature Circuit B
temp_p (105)
temp_p (105) Entering Water Temperature Circuit A
temp_p (105) Entering Water Temperature Circuit B
temp_p (105)
temp_p (105)
temp_p (105)
temp_p (105)
enthalpy (153) Economizer Enthalpy Enable Se-tpoint
flow_p (161) Exhaust Fan CFM Set-point
flow_p (161)
flow_p (161) Supply Fan CFM Set-point
lev_percent (81) Dehumidification Set-point
lev_percent (81) Outside Air Damper Minimum Set-point
lev_percent (81) Unoccupied Dehumidification %RH Set-point
ppm (29)
press_p (113) Space Static Pressure Set-point
press_p (113) Supply Duct Static Pressure Set-point
switch (95)
switch (95)
switch (95) Master system enable/disable point
temp_diff_p Heat/Cool Spt Deadband (Space or Return control
(147)
temp_p (105) Economizer Ambient Temp Enable Set-point
temp_p (105) Inside Dewpoint Dehumidification Set-point
temp_p (105) Main Temperature Set-point
temp_p (105) Unoccupied Cooling Set-point
temp_p (105) Unoccupied Heating Set-point
Due to our policy of continuous product innovation, some specifications may change without notification.
©LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. All rights reserved. "LG" is a registered trademark of LG Corp.
Description
Supply Fan Status
Exhaust Fan Status
Heat Wheel Status
Occupied Status
airflow)
General alarm output
Cold Coil Temperature
Exhaust Temperature
Mixed Temperature
Outside Air Temperature
Space Temperature
Supply Temperature
OAD CFM Set-point
Space CO2 Set-point
Occupancy Command
Alarm Reset Command
is active)
CONTROLLER
LonTalk Points
Notes
0=Off 1=On
0=Off 1=On
0=Off 1=On
0=Off 1=On
0=Cooling 1=Heating
0=Unoccupied 1=Occupied
0=Closed 1=Open
0=No Alarms 1=Active Alarms
Heating or Cooling Set-point
Allow Econ when OA Enthalpy<Spt
Divide desired CFM by 100.
Divide desired CFM by 100.
Divide desired CFM by 100.
%RH for Space or Return control
0=Occupied 1=Unoccupied
Divided by 2.
Add/subtract to/from the
set-point
Allow Econ when OAT<Spt
Supply, Space, or Return target
105