Kenwood NX-5300 F2 Service Manual page 48

Item Condition
Panel tuning
mode
[Analog 1) Adj item:
Narrow] [An ADEV]
*2 Adjust:[****]
2) Adj item:
[Low1]→
[Low3]→
[Low5]→
[Center1]→
[Center3]→
[Center5]→
[High2]→
[High4]→
[High6]
*F5,F6,K5,K6
type only: Press
and hold the
[Right] key to en-
ter [Center1]
(Over Lap
High)→
Adjust:[****]
PTT : ON
Press [ ] key to
store the adjust-
ment value.
*2 : Refer to the "4.9.1 Necessary Deviation adjustment item for each signaling and mode" table.
Regarding Maximum Deviation (Analog), it is common with the adjustment of all analog signalings.
8. P25 1) Adj item:
High [P1 PDEV]
Devia- Adjust:[****]
tion Deviation meter
LPF: 3kHz
HPF: OFF
2) Adj item:
[Low1]→
[Low3]→
[Low5]→
[Center1]→
[Center3]→
[Center5]→
[High2]→
[High4]→
[High6]
*F5,F6,K5,K6
type only: Press
and hold the
[Right] key to en-
ter [Center1]
(Over Lap
High)→
Adjust:[****]
PTT : ON
Press [ ] key to
store the adjust-
ment value.
1-48 (No.RA015<Rev.001>)
Measurement
PC test mode Test-
equip-
ment
1) Adj item: Devia-
[Maxmum Devia- tion
tion (Analog Nar- meter
row)] Oscil-
2) Adj item: lo-
[Low1]→ scope
[Low3]→
[Low5]→
[Center1]→
[Center3]→
[Center5]→
[High2]→
[High4]→
[High6]
*F5,F6,K5,K6 type
only: [Center1]
(Over Lap High)→
Press [Transmit]
button.
Press [Apply All]
button to store the
adjustment value.
1) Adj item: Devia-
[P25 High Devia- tion
tion] meter
Deviation meter Oscil-
LPF: 3kHz lo-
HPF: OFF scope
2) Adj item:
[Low1]→
[Low3]→
[Low5]→
[Center1]→
[Center3]→
[Center5]→
[High2]→
[High4]→
[High6]
*F5,F6,K5,K6 type
only: [Center1]
(Over Lap High)→
Press [Transmit]
button.
Press [Apply All]
button to store the
adjustment value.
Unit Ter- Unit Parts
minal
Panel ANT Panel [Panel
tuning
mode]
[ ],
[ ]
[PC
test
mode]
[←],
[→]
Panel ANT Panel [Panel
tuning
mode]
[ ],
[ ]
[PC
test
mode]
[←],
[→]
Adjustment
Method
Write fixed value "494" 2050~2150Hz
(F2,F3,K2,K3),"491"
(F5,F6,K5,K6) for each [PC test
adjustment point. Trans- mode]
mit at each adjustment Press [Apply
point and check that the All] button to
deviation is between store the
2050Hz and 2150Hz. adjustment
Deviation meter value after all
LPF: 15kHz adjustment
HPF: OFF points have
been adjusted.
[Panel tuning mode]
PTT: ON
[PC test mode]
PTT: Press [Transmit]
button
Write fixed value "498" 2771~2883Hz
(F2,F3,K2,K3),"497"
(F5,F6,K5,K6) for each [PC test
adjustment point. Trans- mode]
mit at each adjustment Press [Apply
point and check that the All] button to
deviation is between store the
2771Hz and 2883Hz. adjustment
Deviation meter value after all
LPF: 3kHz adjustment
HPF: OFF points have
been adjusted.
[Panel tuning mode]
PTT: ON
[PC test mode]
PTT: Press [Transmit]
button
Specifica-
tions
/Remarks