Kenwood NX-5300 F2 Service Manual page 47

Item Condition
Panel tuning
mode
6. 1) Adj item: [BAL]
Balance Adjust:[****]
*1 Deviation meter
LPF: 15kHz
HPF: OFF
Detector:P-P/2
2) Adj item:
[Low1]→
[Low3]→
[Low5]→
[Center1]→
[Center3]→
[Center5]→
[High2]→
[High4]→
[High6]
*F5,F6,K5,K6
type only: Press
and hold the [ ]
key to enter
[Center1] (Over
Lap High)→
Adjust:[****]
PTT : ON
Press [ ] key to
store the adjust-
ment value.
*1 : Refer to the "4.9.1 Necessary Deviation adjustment item for each signaling and mode" table.
Balance adjustment is common with the adjustment of all signaling deviations.
7. 1) Adj item: [ADEV]
Maxi- Adjust:[****]
mum Deviation meter
Devia- LPF: 15kHz
tion HPF: OFF
*2 2) Adj item:
[Low1]→
[Analog [Low3]→
Wide] [Low5]→
[Center1]→
[Center3]→
[Center5]→
[High2]→
[High4]→
[High6]
*F5,F6,K5,K6
type only: Press
and hold the
[Right] key to en-
ter [Center1]
(Over Lap
High)→
Adjust:[****]
PTT : ON
Press [ ] key to
store the adjust-
ment value.
Measurement
PC test mode Test-
equip-
ment
1) Adj item: Devia-
[Balance] tion
Deviation meter meter
LPF: 15kHz Oscillo-
HPF: OFF scope
Detector:P-P/2
2) Adj item:
[Low1]→
[Low3]→
[Low5]→
[Center1]→
[Center3]→
[Center5]→
[High2]→
[High4]→
[High6]
*F5,F6,K5,K6 type
only: [Center1]
(Over Lap High)→
Press [Transmit]
button.
Press [Apply All]
button to store the
adjustment value.
1) Adj item: Devia-
[Maxmum Devia- tion
tion (Analog Wide)] meter
Deviation meter Oscil-
LPF: 15kHz lo-
HPF: OFF scope
2) Adj item:
[Low1]→
[Low3]→
[Low5]→
[Center1]→
[Center3]→
[Center5]→
[High2]→
[High4]→
[High6]
*F5,F6,K5,K6 type
only: [Center1]
(Over Lap High)→
Press [Transmit]
button.
Press [Apply All]
button to store the
adjustment value.
Unit Ter- Unit Parts
minal
Panel ANT Panel [Panel
tuning
mode]
[ ],
[ ]
[PC
test
mode]
[←],
[→]
Panel ANT Panel [Panel
tuning
mode]
[ ],
[ ]
[PC
test
mode]
[←],
[→]
Adjustment
Method
The Deviation of 20Hz 6kHz Tone de-
frequency is fixed. viation is with-
Change the 6kHz ad- in 96 ± 1% of
justment value to be- 20Hz tone de-
come the 96% deviation viation.
of 20Hz within the spec-
ified range. [PC test
mode]
(a supplementary Press [Apply
explanation: All] button to
Another way to adjust is store the
ready. adjustment
(Same as TK-5300, the value after all
old model of NX-5300). adjustment
Press [AUX(Orange)] points have
key to switch the tone to been adjusted.
100Hz square wave.
Then, make the demod-
ulation waveform shown
on oscilloscope into
square shape.)
Write fixed value "496" 4150~4250Hz
(F2,F3,K2,K3), "494"
(F5,F6,K5,K6) for each [PC test
adjustment point. Trans- mode]
mit at each adjustment Press [Apply
point and check that the All] button to
deviation is between store the
4150Hz and 4250Hz. adjustment
Deviation meter value after all
LPF: 15kHz adjustment
HPF: OFF points have
been adjusted.
[Panel tuning mode]
PTT: ON
[PC test mode]
PTT: Press [Transmit]
button
(No.RA015<Rev.001>)1-47
Specifica-
tions
/Remarks