- will be able to have a complete reference on hand at all times. Note: The illustrations, descriptions and specifications in this manual are not binding. LIPCO reserves the right to make modifications without notice. 3 - 24 LIPCO 110037B-20-E BA UF70L_80L_90L_100L / 29.12.2009...
Adjustment of working depth / roller adjustment 10. Maintenance 11. Replacement of cutting blades 12. After use 13. Disposal after end of lifetime of the machine 14. Notices 15. Guarantee 16. EC Declaration of conformity 4 - 24 LIPCO 110037B-20-E BA UF70L_80L_90L_100L / 29.12.2009...
The manufacturer cannot held liable for damage resulting from unauthorised modifications of the LIPCO Reversing Harrow 5 - 24 LIPCO 110037B-20-E BA UF70L_80L_90L_100L / 29.12.2009...
With the drive switched on and the motor running, maintain sufficient distance to rotating tools. With the motor running, there is a risk of parts being hurled away – maintain safety distance. Do not reach into rotating tools. 6 - 24 LIPCO 110037B-20-E BA UF70L_80L_90L_100L / 29.12.2009...
The warnings and signs attached to the unit give important information on safe operation; observing these instructions ensures your safety! 7 - 24 LIPCO 110037B-20-E BA UF70L_80L_90L_100L / 29.12.2009...
Page 8
Operating instructions Reversing harrow UF 70L/ 80L/ 90L/ 100L Do not wear wide or loose clothes (e.g. scarves)! When working with the machine, you must wear safety shoes. 8 - 24 LIPCO 110037B-20-E BA UF70L_80L_90L_100L / 29.12.2009...
During service or repair work, make sure that no one can start up the machine accidentally! Do not wear wide or loose clothes (e.g. scarves)! Do not, for any reason, climb onto the machine during operation! 9 - 24 LIPCO 110037B-20-E BA UF70L_80L_90L_100L / 29.12.2009...
Page 10
Operating instructions Reversing harrow UF 70L/ 80L/ 90L/ 100L Never work without machine protection! Do not act with any objects on the machine during operation! 10 - 24 LIPCO 110037B-20-E BA UF70L_80L_90L_100L / 29.12.2009...
The noise produced in this process serves as warning signal. Attention! When the rattling noise of the locking body is heard, the power takeoff shaft has to be turned off! Star ratchet Fig. 2 Fig. 1 11 - 24 LIPCO 110037B-20-E BA UF70L_80L_90L_100L / 29.12.2009...
8 working hours. To do so, you must open the protective hood (Fig. 1 Ref. C). Lubricating point: Lubricating nipples (3x) Star ratchet Joint Joint Fig. 3 12 - 24 LIPCO 110037B-20-E BA UF70L_80L_90L_100L / 29.12.2009...
Attention: The working direction must be regarded ! Working against the above specified working direction can cause heavy damages on the machine, for which LIPCO denies any responsibility! Remarks about noise and vibration: It is not expected, that the values for noise and vibration of these attachment unit will exceed the values of the engine-driven machine.
Then secure the connection between the engine-driven machine and the unit. Before commencing work, lubricate drive flange on the lubricating nipple (Fig. 4, Ref. E)! Fig. 4 14 - 24 LIPCO 110037B-20-E BA UF70L_80L_90L_100L / 29.12.2009...
(Fig. 6) to enable driving right to the edge of enclosures or walls. To shift the roller, only the two clamping screws (Fig. 6, Ref. C) are loosened, the roller is shifted to the desired position and tightened again. 15 - 24 LIPCO 110037B-20-E BA UF70L_80L_90L_100L / 29.12.2009...
30 to 50 operating hours. Further oil changes after every 200 operating hours or once a year. Use gear oil SAE 90. (Amount of oil 0.3 L) Angular gear: Oil plug Oil gauge glass Fig. 8 16 - 24 LIPCO 110037B-20-E BA UF70L_80L_90L_100L / 29.12.2009...
Page 17
Then check the grease level with a dipstick (grease level should be at least 5 cm, measured from the lowest point of the chain case to ensure that the chain is always sufficiently lubricated). 17 - 24 LIPCO 110037B-20-E BA UF70L_80L_90L_100L / 29.12.2009...
Page 18
Reversing harrow UF 70L/ 80L/ 90L/ 100L Lubricating of chain: Plug for lubrication of chain drive. Fig. 10 If necessary, top up liquid gear grease (based on sodium bicarbonate - type GP 00). 18 - 24 LIPCO 110037B-20-E BA UF70L_80L_90L_100L / 29.12.2009...
When replacing them, it is very important to maintain blade arrangement, especially the direction of cutting edge. blades must always be mounted in the cutting direction towards Fig. 14 supporting roller. 19 - 24 LIPCO 110037B-20-E BA UF70L_80L_90L_100L / 29.12.2009...
Before using the unit again, follow the instructions in chapter "10. Maintenance". 13. Disposal after end of lifetime of the machine The disposal of the machine, machine parts, consumables and lubricants has to follow the legal laws. 20 - 24 LIPCO 110037B-20-E BA UF70L_80L_90L_100L / 29.12.2009...
Operating instructions Reversing harrow UF 70L/ 80L/ 90L/ 100L 15. Guarantee LIPCO products come with a guarantee against factory or assembly defects. The guarantee concerns the replacement of demonstrably defective parts. The guarantee period depends on the legal situation in effect at the time of delivery of the machines to the customer.
+49 (0) 761 5565 576 Internet http://www.lipco.com E-Mail mail@bauer-ib.com Denomination: LIPCO Reversing Harrow UF 70L / 80L / 90L /100L Serial no: Year of manufacture: The manufacturer declares expressly, that the machinery fulfills all the relevant provisions of the ...
Need help?
Do you have a question about the Reversing Harrow UF 80L and is the answer not in the manual?
Questions and answers