Page 1 User Manual Stratix Managed Switches Stratix 5400 Switches (1783-HMS) Stratix 5700 Switches (1783-BMS) ArmorStratix 5700 Switches (1783-ZMS) Stratix 8000 and 8300 Switches (1783-MS, 1783-RMS, 1783-MX)
Page 2 Regulatory requirements for safe work practices and for Personal Protective Equipment (PPE). Allen-Bradley, ArmorStratix, Logix5000, Rockwell Automation, Rockwell Software, RSLinx, RSLogix, RSNetWorx, Stratix 2000, Stratix 5700, Stratix 8000, Stratix 8300, Studio 5000, Studio 5000 Automation Engineering & Design Environment, and Studio 5000 Logix Designer are trademarks of Rockwell Automation, Inc.
Page 3 Stratix 5400 SD card 125, 144 Precision time protocol (PTP) configuration on the VLAN of a trunk port Stratix 5400 time synchronization in the Logix Designer application Stratix 5400 default multicast groups Stratix 5400 Layer 3 routing Stratix 5400 front panel and status indicators...
Page 4 Summary of Changes Notes: Rockwell Automation Publication 1783-UM007B-EN-P - March 2015...
Page 5: Table Of Contents
Stratix 5400 Templates ........
Page 6 Table of Contents Attach the Switch Power Connectors ......67 Wire the Power over Ethernet DC Power Source....68 Attach the PoE Power Connector.
Page 7 Stratix 5400 switches) ........
Page 8 Configure REP via Device Manager ......239 Layer 3 Routing (Stratix 8300 and Stratix 5400 Layer 3 firmware switches). 240 Types of Routing .
Page 9 Stratix 5400, Stratix 5700, and ArmorStratix 5700 Status Indicators . 269 Stratix 5400 Display Mode Switch ......272 Stratix 8000 and 8300 Front Panel Status Indicators .
Page 10 Stratix 5400 Data Types ........
Page 11 Stratix 5400 Port Assignments ........364...
Page 12 Table of Contents Notes: Rockwell Automation Publication 1783-UM007B-EN-P - March 2015...
Page 13: Preface
Preface This publication describes the embedded software features and tools for configuring and managing Stratix™ managed switches. In addition, this publication provides troubleshooting information to help you resolve basic switch and network issues. This manual assumes you understand the following: •...
Page 14: Access Product Release Notes
Preface Access Product Release Notes Product release notes are available online within the Product Compatibility and Download Center. 1. From the Quick Links list on http://www.ab.com, choose Product Compatibility and Download Center. 2. From the Compatibility Scenarios tab or the Get Downloads tab, search for and choose your product.
Page 15: Additional Resources
You can view or download publications at http:/www.rockwellautomation.com/literature/. To order paper copies of technical documentation, contact your local Allen-Bradley distributor or Rockwell Automation sales representative. For information on additional software features or further configuration, see these Cisco publications at http://www.Cisco.com: •...
Page 16 Preface Notes: Rockwell Automation Publication 1783-UM007B-EN-P - March 2015...
Page 17 Chapter About the Switches Topic Page EtherNet/IP CIP Interface Lite Versus Full Firmware Features (Stratix 5700 switches) Software Features Hardware Features Memory Allocation Stratix managed switches provide a secure switching infrastructure for harsh environments. You can connect the switches to network devices such as servers, routers, and other switches.
Page 18: About The Switches
About the Switches Table 1 - Stratix Switches Switch Family Description Stratix 5400™ switches Layer 2 and Layer 3 scalable managed switches. Available in 8…20 port versions, including all Gigabit port versions. Stratix 5700™ switches Layer 2 scalable managed switches.
Page 19: Cip Network Connections
About the Switches Chapter 1 CIP Network Connections CIP is an object-oriented, connection-based protocol that supports two basic types of messaging: • Explicit • Implicit (I/O) A maximum of 32 connections is available. Both connection types must use the switch password before any switch parameters can be written. The password is the same one you enter during Express Setup.
Page 20: Lite Versus Full Firmware Features (Stratix 5700 Switches)
Chapter 1 About the Switches Lite Versus Full Some features for Stratix 5700 switches depend on whether the switches have Full or Lite firmware. All Stratix 8000 and ArmorStratix 5700 switches have Full Firmware Features firmware. (Stratix 5700 switches) To determine the firmware type available for specific catalog numbers, see the Stratix 5700 switch descriptions in Table 111 on page 378.
Page 21: Software Features
Port Mirroring • Port Security • • Port Thresholds • • Power over Ethernet (PoE) Stratix 5400 switches: 1783-HMS4T4E4CGN, 1783-HMS8S8E4CGN, • • 1783-HMS4EG8CGN, 1783-HMS8TG8EG4CGN, 1783-HMS4SG8EG4CGN, 1783-HMS4EG8CGR, 1783-HMS8TG8EG4CGR, 1783-HMS4SG8EG4CGR Stratix 5700 switches:1783-BMS12T4E2CGNK, 1783-BMS12T4E2CGP, 1783-BMS12T4E2CGL ArmorStratix switches: 1783-ZMS4T4E2TGP, 1783-ZMS8T8E2TGP, 1783-ZMS4T4E2TGN, 1783-ZMS8T8E2TGN Stratix 8000/8300 expansion modules: 1783-MX04E, 1783-MX04T04E Resilient Ethernet Protocol (REP) •...
Page 22: Hardware Features
To configure, monitor, and manage a switch, you can connect a switch to a computer through the console port: • Stratix 5400 and Stratix 5700 switches—Connect to the console port with an RJ45-to-DB-9 adapter cable or a mini USB cable. The mini USB driver is available in the firmware download section at http://www.rockwellautomation.com.
Page 23: Memory Allocation
ACL usage. To allocate hardware resources for different usages, the switch SDM templates prioritize system resources to optimize support for certain features. Stratix 5400 Templates The following SDM templates are available. • Layer 2 firmware models –...
Page 24: Stratix 5700 And Armorstratix 5700 Templates
Chapter 1 About the Switches Stratix 5700 and ArmorStratix 5700 Templates The following SDM templates are available: • Default • Lanbase Routing • Dual IPv4 and IPv6 If you enable static routing, or if you have more than 180 IGMP groups or multicast routes., consider using the routing template.
Page 25: Stratix 8000 And 8300 Templates
About the Switches Chapter 1 Stratix 8000 and 8300 Templates The following SDM templates are recommended: • Default • Lanbase Routing For static and connected routing, or if you have more than 180 IGMP groups or multicast routes, you can use the Lanbase Routing template. Other SDM templates are available, but are not covered in detail.
Page 26 Chapter 1 About the Switches Notes: Rockwell Automation Publication 1783-UM007B-EN-P - March 2015...
Page 27: Install Stratix 5400 Switches
Chapter Install Stratix 5400 Switches Topic Page Overview Parts List and Required Tools Install or Remove the SD Card Verify Switch Operation Mount the Switch on a DIN Rail Remove the Switch from the DIN Rail Ground the Switch Wire the Switch DC Power Source...
Page 28 Chapter 2 Install Stratix 5400 Switches North American Hazardous Location Approval The following information applies when operating this equipment in Informations sur l’utilisation de cet équipement en environnements hazardous locations. dangereux. Products marked "CL I, DIV 2, GP A, B, C, D" are suitable for use in Class I Division 2 Groups Les produits marqués "CL I, DIV 2, GP A, B, C, D"...
Page 29 Install Stratix 5400 Switches Chapter 2 WARNING: Do not use the USB-mini console port in hazardous locations. European Hazardous Location Approval The following applies to products marked II 3 G: Such modules: • Are Equipment Group II, Equipment Category 3, and comply with the Essential Health and Safety Requirements relating to the design and construction of such equipment given in Annex II to Directive 94/9/EC.
Page 30: Overview
Chapter 2 Install Stratix 5400 Switches ATTENTION: Installation, adjustments, putting into service, use, assembly, disassembly, and maintenance shall be carried out by suitably trained personnel in accordance with applicable code of practice. In case of malfunction or damage, no attempts at repair should be made.
Page 31 Install Stratix 5400 Switches Chapter 2 • Temperature surrounding the unit does not exceed 70 °C (158 °F). When the switch is installed in an industrial enclosure, the IMPORTANT temperature within the enclosure is greater than normal room temperature outside the enclosure.
Page 32: Parts List And Required Tools
Chapter 2 Install Stratix 5400 Switches Parts List and Required Tools Verify that you have these items. The secure digital (SD) card comes installed in the SD slot on the front panel of the switch. Stratix 5400 switch SD card...
Page 33: Install Or Remove The Sd Card
Chapter 2 Install or Remove the SD Card A secure digital (SD) card ships with the Stratix 5400 switch. The SD card contains the switch firmware and initial configuration. You can order a replacement SD card from Rockwell Automation, catalog number 1784-SD1, if needed.
Page 34: Verify Switch Operation
Chapter 2 Install Stratix 5400 Switches Verify Switch Operation Before installing the switch in its final location, power on the switch, and verify that the switch powers up. The time that is required for the switch to start up is directly related to your switch configuration.
Page 35: Mount The Switch On A Din Rail
Install Stratix 5400 Switches Chapter 2 Mount the Switch The switch ships with a spring-loaded latch on the rear panel for mounting on a DIN rail. on a DIN Rail ATTENTION: To prevent the switch from overheating, make sure these minimum clearances: •...
Page 36: Ground The Switch
Chapter 2 Install Stratix 5400 Switches Ground the Switch For DC power connections, use UL- and CSA-rated, style 1007 or 1569 twisted-pair copper appliance wiring material (AWM) wire. ATTENTION: To make sure that the equipment is reliably connected to earth ground, follow the grounding procedure instructions and use a suitable ring terminal lug, such as Thomas &...
Page 37: Wire The Switch Dc Power Source
For switches with Power over Ethernet (PoE) capability, PoE power is drawn from the single power connection. There is no separate power input for PoE. DC Power Source Switch Configuration Required Voltage Input Power Supplied per Port Allen-Bradley Products 44-54V 15.4 W, max Switched mode power supplies:...
Page 38 Chapter 2 Install Stratix 5400 Switches 3. Measure a length of 0.82…0.52 mm (18…20 AWG) copper wire long enough to connect to the DC power source. 4. Use an 18-gauge wire-stripping tool to strip each of the two wires to 6.3 mm (0.25 in.) ±...
Page 39 Install Stratix 5400 Switches Chapter 2 7. Use a ratcheting-torque screwdriver to torque the captive screws of the power connector to 0.23 N•m (2.0 lb•in). Do not exceed the recommended torque. 32281-M 8. Connect the other end of the positive wire to the positive terminal on the DC power source.
Page 40: Attach The Switch Power Connectors
Chapter 2 Install Stratix 5400 Switches Attach the Switch To attach the switch power connectors to the front panel of the switch, follow these steps. There is no separate power connector for PoE. Power Connectors 1. Insert one power connector into the Pwr A receptacle on the switch front panel, and the other into the Pwr B receptacle.
Page 41: Install An Sfp Module
Install Stratix 5400 Switches Chapter 2 5. Use a ratcheting-torque screwdriver to torque the captive screws of the power connector to 0.23 N•m (2.0 lb•in). 6. Connect the other end of the positive wire (the one connected to DC+) to the positive terminal on the DC power source.
Page 42 Chapter 2 Install Stratix 5400 Switches On switch catalog numbers that support communication over fiber-optic cable, SFP modules are inserted into SFP module slots on the front of the switch. These field-replaceable modules provide the uplink optical interfaces, send (TX) and receive (RX).
Page 43: Remove Sfp Modules From Sfp Module Slots
Install Stratix 5400 Switches Chapter 2 Remove SFP Modules To remove an SFP module from a module receptacle, follow these steps. from SFP Module Slots 1. Attach an ESD-preventive wriststrap to your wrist and to a grounded bare metal surface.
Page 44: Wire The External Alarms
Chapter 2 Install Stratix 5400 Switches Wire the External Alarms The switch has two alarm inputs and one Form C (single-pole, double-throw) alarm output relay circuits for external alarms. The input alarm relay circuits are designed to sense if the alarm input is open or closed relative to the alarm input reference pin.
Page 45 Install Stratix 5400 Switches Chapter 2 The labels for the alarm relay connector are on the switch panel. Table 2 - Alarm Relay Connector Labels Label Connection Alarm Output Normally Open (NO) connection Alarm Output Common connection Alarm Output Normally Closed (NC) connection...
Page 46 Chapter 2 Install Stratix 5400 Switches 5. Use a ratcheting torque flathead screwdriver to torque the captive screw of the alarm relay connector to 0.23 N•m (2.0 lb•in). Do not exceed the recommended torque. REF - External Device Connection 2...
Page 47: Attach The Alarm Relay Connector To The Switch
Install Stratix 5400 Switches Chapter 2 Attach the Alarm Relay To attach the alarm relay connector to the front panel of the switch, follow these steps. Connector to the Switch 1. Insert the alarm relay connector into the receptacle on the switch front panel.
Page 48: Connect To 10Base-T, 100Base-Tx, Or 1000Base-T Ports
Chapter 2 Install Stratix 5400 Switches Connect to 10BASE-T, To connect to 10BASE-T, 100BASE-TX, or 1000BASE-T ports, follow these steps. 100BASE-TX, or 1000BASE-T Ports ATTENTION: To prevent electrostatic-discharge (ESD) damage, follow recommended board and component handling procedures. 1. Choose one of these options to connect a device: •...
Page 49: Connect To Poe Ports
Install Stratix 5400 Switches Chapter 2 Connect to PoE Ports Switches with PoE ports require a separate power supply. For power supply requirements based on your application, refer to page 1. Insert a straight-through, twisted four-pair, Category 5e or better cable with an RJ45 connector into the PoE port.
Page 50: Connect To A Dual-Purpose Port
Chapter 2 Install Stratix 5400 Switches Connect to a A dual-purpose port is one port with two interfaces, one for an RJ45 cable and another for an approved SFP module. Only one interface can be active at a time. Dual-purpose Port If both interfaces are connected, the SFP module has priority.
Page 51 Chapter Install Stratix 5700 Switches Topic Page Overview Parts List and Required Tools Install or Remove the SD Card Verify Switch Operation Mount the Switch on a DIN Rail Remove the Switch from the DIN Rail Ground the Switch Wire the Switch DC Power Source Attach the Switch Power Connectors Wire the Power over Ethernet DC Power Source Attach the PoE Power Connector...
Page 52: Install Stratix 5700 Switches
Chapter 3 Install Stratix 5700 Switches ATTENTION: Environment and Enclosure This equipment is intended for use in a Pollution Degree 2 industrial environment, in overvoltage Category II applications (as defined in IEC 60664-1), at altitudes up to 2000 m (6562 ft) without derating. This equipment is not intended for use in residential environments and may not provide adequate protection to radio communication services in such environments.
Page 53: Overview
Install Stratix 5700 Switches Chapter 3 ATTENTION: This equipment is not resistant to sunlight or other sources of UV radiation. WARNING: • This equipment shall be mounted in an ATEX-certified enclosure with a minimum ingress protection rating of at least IP54 (as defined in IEC60529) and used in an environment of not more than Pollution Degree 2 (as defined in IEC 60664-1) when applied in Zone 2 environments.
Page 54 Chapter 3 Install Stratix 5700 Switches • For maximum noise immunity, shielded cables must be used on the RJ45 uplink ports (Gi1/1 and Gi1/2) on these switches: – 1783-BMS06TGL – 1783-BMS06TGA – 1783-BMS10CGL – 1783-BMS10CGA – 1783-BMS10CGN – 1783-BMS10CGP – 1783-BMS12T4E2CGNK –...
Page 55: Parts List And Required Tools
Install Stratix 5700 Switches Chapter 3 Follow these steps to install the switch. 1. (Optional) Install the SD card. 2. Verify switch operation. 3. Mount the switch on a DIN rail. 4. Ground the switch. 5. Wire the DC power source for the switch and attach the switch power connectors.
Page 56: Install Or Remove The Sd Card
Chapter 3 Install Stratix 5700 Switches Obtain these tools: • Ratcheting torque screwdriver that exerts up to 1.69 N m (15 in lbs) of • • pressure • Small, flat-blade screwdriver  • #6 ring terminal lug for 5.3 mm (10 AWG) wire, such as Thomas &...
Page 57 Install Stratix 5700 Switches Chapter 3 3. Install or remove the card: • To install the card, slide it into the slot, and press it firmly in place until it latches in the spring loaded mechanism. The card is keyed so that you cannot fully insert it the wrong way.
Page 58: Verify Switch Operation
Chapter 3 Install Stratix 5700 Switches Verify Switch Operation Before installing the switch in its final location, power on the switch, and verify that the switch powers up. The time that is required for the switch to start up is directly related to your switch configuration.
Page 59: Mount The Switch On A Din Rail
Install Stratix 5700 Switches Chapter 3 Mount the Switch The switch ships with a spring-loaded latch on the rear panel for mounting on a DIN rail. on a DIN Rail WARNING: If you connect or disconnect console port cables with power applied to this module or any device on the network, an electrical arc can occur.
Page 60 Chapter 3 Install Stratix 5700 Switches ATTENTION: Class 1 laser product. Laser radiation is present when the system is open and interlocks bypassed. Only trained and qualified personnel should be allowed to install, replace, or service this equipment. ATTENTION: This product is grounded through the DIN rail to chassis ground. Use zinc plated yellow-chromate steel DIN rail to assure proper grounding.
Page 61: Remove The Switch From The Din Rail
Install Stratix 5700 Switches Chapter 3 Remove the Switch To remove the switch from a DIN rail or a rack, follow these steps. from the DIN Rail 1. Remove power from the switch, and disconnect all cables and connectors from the front panel of the switch. 2.
Page 62 Chapter 3 Install Stratix 5700 Switches Use at least 4 mm (12 AWG) wire to connect to the external grounding screw. The ground lug is not supplied with the switch. You can use one of the these options: • Single ring terminal •...
Page 63: Wire The Switch Dc Power Source
Install Stratix 5700 Switches Chapter 3 5. Insert the ground screw into the functional ground screw opening on the front panel. Ring Terminal Lug (single lug shown) 32276-M 6. Use a ratcheting torque screwdriver to tighten the ground screws and ring terminal lugs to the switch front panel to 0.4 N m (3.5 lb in).
Page 64 Chapter 3 Install Stratix 5700 Switches 1. Locate the power connector. 32280-M 2. Identify the positive and return DC power connections. The positive DC power connection is labeled DC+, and the negative DC power connection is the adjacent connection labeled DC-. 3.
Page 65 Install Stratix 5700 Switches Chapter 3 6. Insert the exposed part of the positive wire into the connection labeled DC+ and the exposed part of the return wire into the connection labeled DC-. Be sure that you cannot see any wire lead. Only wire with insulation can extend from the connector.
Page 66 Chapter 3 Install Stratix 5700 Switches 8. Connect the other end of the positive wire to the positive terminal on the DC power source. 9. Connect the other end of the return wire to the return terminal on the DC power source.
Page 67: Attach The Switch Power Connectors
Install Stratix 5700 Switches Chapter 3 Attach the Switch To attach the switch power connectors to the front panel of the switch, follow these steps. Power Connectors 1. Insert one power connector into the Pwr A receptacle on the switch front panel, and the other into the Pwr B receptacle.
Page 68: Wire The Power Over Ethernet Dc Power Source
The switch must be wired and grounded. Power input requirements depend on your application. Application Power Supply per Port Power Consumption Allen-Bradley Products PoE only 44…57V DC (48V DC nom) 15.4 W, max Switched mode power supplies: • 1606-XL Standard IEEE 802.3af...
Page 69: Attach The Poe Power Connector
Install Stratix 5700 Switches Chapter 3 4. Insert the exposed part of the positive wire into the DC+ connection and the exposed part of the return wire into the DC- connection. Make sure that you cannot see any wire lead. Only wire with insulation can extend from the connector.
Page 70: Install An Sfp Module
Chapter 3 Install Stratix 5700 Switches Install an SFP Module WARNING: When you insert or remove the small form-factor pluggable (SFP) optical transceiver while power is on, an electrical arc can occur. This could cause an explosion in hazardous location installations. Be sure that power is removed or the area is nonhazardous before proceeding.
Page 71: Remove Sfp Modules From Sfp Module Slots
Install Stratix 5700 Switches Chapter 3 3. Insert the SFP module into the slot as shown in the following figure until you feel the connector on the module snap into place in the rear of the slot. SFP Module (Bale-type Latch Shown) 32293-M 4.
Page 72 Chapter 3 Install Stratix 5700 Switches 4. Unlock and remove the SFP module. If the module has a bale-clasp latch, swing the bale toward you and pull it gently to eject the module. If the bale-clasp latch is obstructed and you cannot use your index finger to open it, use a small, flat-blade screwdriver or other long, narrow instrument to open the latch.
Page 73: Wire The External Alarms
Install Stratix 5700 Switches Chapter 3 Wire the External Alarms The switch has two alarm inputs and one Form C (single-pole, double-throw) alarm output relay circuits for external alarms. The input alarm relay circuits are designed to sense if the alarm input is open or closed relative to the alarm input reference pin.
Page 74 Chapter 3 Install Stratix 5700 Switches The labels for the alarm relay connector are on the switch panel. Table 3 - Alarm Relay Connector Labels Label Connection Alarm Output Normally Open (NO) connection Alarm Output Common connection Alarm Output Normally Closed (NC) connection Alarm Input 2 Alarm Input Reference Ground connection Alarm Input 1...
Page 75 Install Stratix 5700 Switches Chapter 3 5. Use a ratcheting torque flathead screwdriver to torque the captive screw of the alarm relay connector to 0.23 N•m (2.0 lb•in). Do not exceed the recommended torque. REF - External Device Connection 2 IN1 - External Device Connection 1 32288-M 6.
Page 76: Attach The Alarm Relay Connector To The Switch
Chapter 3 Install Stratix 5700 Switches Attach the Alarm Relay To attach the alarm relay connector to the front panel of the switch, follow these steps. Connector to the Switch 1. Insert the alarm relay connector into the receptacle on the switch front panel.
Page 77: Connect To 10Base-T, 100Base-Tx, Or 1000Base-T Ports
Install Stratix 5700 Switches Chapter 3 Connect to 10BASE-T, To connect to 10BASE-T, 100BASE-TX, or 1000BASE-T ports, follow these steps. 100BASE-TX, or 1000BASE-T Ports ATTENTION: To prevent electrostatic-discharge (ESD) damage, follow recommended board and component handling procedures. 1. Choose one of these options to connect a device: •...
Page 78: Connect To Poe Ports
Chapter 3 Install Stratix 5700 Switches Connect to PoE Ports Switches with PoE ports require a separate power supply. For power supply requirements based on your application, refer to page 1. Insert a straight-through, twisted four-pair, Category 5e or better cable with an RJ45 connector into the PoE port.
Page 79: Connect To A Dual-Purpose Port
Install Stratix 5700 Switches Chapter 3 4. Observe the port status indicator: • The status indicator turns amber while the SFP discovers the network topology and searches for loops. This process takes about 30 seconds, and then the port status indicator turns green. •...
Page 80 Chapter 3 Install Stratix 5700 Switches Notes: Rockwell Automation Publication 1783-UM007B-EN-P - March 2015...
Page 81 Chapter Install ArmorStratix 5700 Switches Topic Page Overview Parts List and Required Tools Install or Remove the SD Card Verify Switch Operation Mount the Switch Ground the Switch Connect the Switch to a DC Power Source Wire External Alarms Connect to 10/100 and 100/1000 Ports 10/100 PoE Ports ATTENTION: Environment and Enclosure This equipment is intended for use in overvoltage Category II applications (as...
Page 82: Install Armorstratix 5700 Switches
Chapter 4 Install ArmorStratix 5700 Switches ATTENTION: Prevent Electrostatic Discharge This equipment is sensitive to electrostatic discharge, which can cause internal damage and affect normal operation. Follow these guidelines when you handle this equipment: • Do not touch connectors or pins on component boards. •...
Page 83: Parts List And Required Tools
Install ArmorStratix 5700 Switches Chapter 4 • Cabling is away from sources of electrical noise, such as radios, power lines, and fluorescent lighting fixtures. • Connect the unit to only an IP67-rated power supply. Rockwell Automation offers a Bulletin 1607 IP67-rated power supply to provide 24V DC power to the switch.
Page 84 Chapter 4 Install ArmorStratix 5700 Switches Obtain these tools: • An IP67-rated cordset or patchcord with a female-end, 4-pin mini connector to provide 24V DC power to the switch • Ratcheting torque screwdriver that exerts up to 1.69 N m (15 in lbs) of •...
Page 85: Install Or Remove The Sd Card
Install ArmorStratix 5700 Switches Chapter 4 Install or Remove the SD Card The switch supports a Secure Digital (SD) memory card to store firmware and the startup configuration. This storage makes it possible to replace a switch without reconfiguring the replacement switch. The SD card cover protects the card against shock and vibration by holding the card in place.
Page 86: Verify Switch Operation
Chapter 4 Install ArmorStratix 5700 Switches Verify Switch Operation Before installing the switch in its final location, power on the switch, and verify that the switch powers up. The time that is required for the switch to start up is directly related to your switch configuration.
Page 87: Mount The Switch
Install ArmorStratix 5700 Switches Chapter 4 Mount the Switch ATTENTION: To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety: •...
Page 88 Chapter 4 Install ArmorStratix 5700 Switches Use at least 4 mm (12 AWG) wire to connect to the external grounding screw. The ground lug is not supplied with the switch. You can use one of these options: • Single ring terminal •...
Page 89: Connect The Switch To A Dc Power Source
Install ArmorStratix 5700 Switches Chapter 4 Connect the Switch to a You must supply a power solution for the device. Use an IP67-rated cordset or patchcord with a female-end, M12 4-pin mini-connector. Rockwell Automation DC Power Source offers a Bulletin 1607 IP67-rated power supply to provide 24V DC power to the switch.
Page 90: Wire External Alarms
Chapter 4 Install ArmorStratix 5700 Switches Wire External Alarms Some switch models have the following for external alarms: • One input alarm relay circuit to sense whether the alarm input is open or closed relative to the alarm input reference pin. •...
Page 91: Connect To 10/100 And 100/1000 Ports
Install ArmorStratix 5700 Switches Chapter 4 The switch 10/100 and 10/100/1000 ports automatically configure themselves Connect to 10/100 and to operate at the speed of attached devices. If the attached ports do not support 100/1000 Ports autonegotiation, you can explicitly set the speed and duplex parameters. Connecting devices that do not autonegotiate or that have their speed and duplex parameters that are manually set can reduce performance or result in no linkage.
Page 92: 100/1000 Ports
Chapter 4 Install ArmorStratix 5700 Switches 100/1000 Ports Gigabit ports are included only on ArmorStratix 5700 switches with PoE. 1. Insert a straight-through, twisted four-pair, Category 6 or better cable with an M12 X-coded connector into a 100/1000 port. 32497 2.
Page 93: Install Stratix 8000 And 8300 Switches
Chapter Install Stratix 8000 and 8300 Switches Topic Page Overview Parts List and Required Tools Attach Expansion Modules (optional) Mount the Switch on a DIN Rail Mount the Switch on a Wall or Panel Install an SFP Module (optional) Ground the Switch Wire the DC Power Source for the Switch Wire the DC Power Source for the PoE Expansion Module Attach the Power and Relay Connector to the Switch to the Switch...
Page 94 Chapter 5 Install Stratix 8000 and 8300 Switches North American Hazardous Location Approval The following information applies when operating this equipment in Informations sur l’utilisation de cet équipement en environnements hazardous locations. dangereux. Products marked "CL I, DIV 2, GP A, B, C, D" are suitable for use in Class I Division 2 Groups Les produits marqués "CL I, DIV 2, GP A, B, C, D"...
Page 95: Overview
Install Stratix 8000 and 8300 Switches Chapter 5 ATTENTION: To comply with the CE Low Voltage Directive (LVD), all connections to this equipment must be powered from a source compliant with safety extra low voltage (SELV) or protected extra low voltage (PELV). To comply with UL restrictions, all connections to this equipment must be powered from a source compliant with Class 2 or Limited Voltage/Current.
Page 96: Parts List And Required Tools
Chapter 5 Install Stratix 8000 and 8300 Switches • Wall or panel 3. (Optional) Install an SFP module. 4. Ground the switch. 5. Wire the DC power source for the switch. 6. (Optional) Wire the DC power source for the PoE expansion module. 7.
Page 97 Install Stratix 8000 and 8300 Switches Chapter 5 31774-M Stratix 8000/8300 switch Documentation Power and alarm relay connectors (qty. 2) Console cable If you plan to install a PoE expansion module, verify that you have a PoE power connector, as shown below. 32437-M At the end of its life, this equipment should be collected separately from any unsorted municipal waste.
Page 98 Chapter 5 Install Stratix 8000 and 8300 Switches Obtain these tools: • Ratcheting torque screwdriver that exerts up to 1.69 N m (15 in lbs) of • • pressure  • #6 ring terminal lug for 5.3 mm (10 AWG) wire, such as Thomas & Bett part number 10RC6 or equivalent •...
Page 99: Attach Expansion Modules (Optional)
Install Stratix 8000 and 8300 Switches Chapter 5 Attach Expansion Modules If you are adding expansion modules, attach the expansion modules to the IMPORTANT (optional) switch before mounting the switch. The switch can operate as a standalone device with two uplink ports and four or eight Fast Ethernet ports, or you can increase the number of Fast Ethernet ports by 8 or 16 by connecting expansion modules.
Page 100 Chapter 5 Install Stratix 8000 and 8300 Switches 2. Remove the protective EMI-connector cover from the side panel. 31787-M 3. Push the upper module latches up and the lower module latches down. Then slide the switch and module together. The expansion module is shown with the side panel removed. Do not remove this panel unless you plan to install another module.
Page 101: Mount The Switch On A Din Rail
Install Stratix 8000 and 8300 Switches Chapter 5 Mount the Switch WARNING: When using DIN rail mounting, additional grounding is also on a DIN Rail accomplished through the DIN rail to chassis ground. Use zinc-plated yellow-chromate steel DIN rail to assist in proper grounding. The use of other DIN rail materials (for example, aluminum or plastic)) that can corrode, oxidize, or are poor conductors, can impede proper grounding.
Page 102: Mount The Switch On A Wall Or Panel
Chapter 5 Install Stratix 8000 and 8300 Switches 3. Position the rear panel of the switch directly in front of the DIN rail, making sure that the DIN rail fits in the space between the two latches. DIN Rail Latch 31778-M 4.
Page 103: Install An Sfp Module (Optional)
Install Stratix 8000 and 8300 Switches Chapter 5 3. Position the rear panel of the switch against the wall or a panel in the desired location, as shown in this figure. o j a i h T t i n i m t h g a h e v r o c .
Page 104: Ground The Switch
Chapter 5 Install Stratix 8000 and 8300 Switches Grasp the module on the sides, and insert it into the switch slot until you feel the connector snap into place. 31782-M ATTENTION: If the SFP module cannot be fully inserted, stop! Do not force the module into the slot.
Page 105: Wire The Dc Power Source For The Switch
Install Stratix 8000 and 8300 Switches Chapter 5 4. Use a crimping tool to crimp the ring terminal to the wire. 31790-M 5. Slide the ground screw through the ring terminal. 6. Insert the ground screw into the ground-screw opening on the front panel. 31791-M 7.
Page 106 Chapter 5 Install Stratix 8000 and 8300 Switches Follow these steps to wire DC power to the switch. 1. Locate the power and alarm relay connector and identify the positive and return DC power connections. The positive DC power connection is labeled V, and the negative DC power connection is the adjacent connection labeled RT.
Page 107: Wire The Dc Power Source For The Poe Expansion Module
Power supply requirements for a PoE expansion module depend on your application. Application Power Consumption Power Supply per Port Allen-Bradley Products PoE only 44…57V DC (48V DC nom) 15.4 W, max Switched mode power supplies: • 1606-XL Standard IEEE 802.3af •...
Page 108 Chapter 5 Install Stratix 8000 and 8300 Switches 3. Use an 18-gauge wire-stripping tool to strip each of the two wires to 6.3 mm (0.25 in.) ± 0.5 mm (0.02 in.). Do not strip more than 6.8 mm (0.27 in.) of insulation from the wire. Stripping more than the recommended amount of wire can leave exposed wire from the connector after installation.
Page 109: Attach The Power And Relay Connector To The Switch
Install Stratix 8000 and 8300 Switches Chapter 5 Attach the Power and ATTENTION: The input voltage source of the alarm circuits must be an isolated Relay Connector source and limited to less than or equal to 24V DC, 1 A. to the Switch ATTENTION: Exposure to some chemicals can degrade the sealing properties of materials used in the relay.
Page 110 Chapter 5 Install Stratix 8000 and 8300 Switches Follow these steps to connect the DC power source and relay connector to the switch. 1. Insert the power and relay connector into the Pwr A receptacle on the switch front panel. 31786-M 2.
Page 111: Attach The Power Connector To The Poe Expansion Module
Install Stratix 8000 and 8300 Switches Chapter 5 Attach the Power Connector If you have a PoE expansion module, follow these steps to connect the DC power source to the PoE expansion module. to the PoE Expansion Module 1. Insert the power connector into the DC input terminal block on the PoE expansion module.
Page 112 Chapter 5 Install Stratix 8000 and 8300 Switches 3. Insert the exposed wires for the external alarm device into the two connections labeled A, as shown in the following figure. External device, relay wire A connection 1 External device, relay wire A connection 2 4.
Page 113: Connect To 10/100 Copper Ports
Install Stratix 8000 and 8300 Switches Chapter 5 Connect to 10/100 1. Insert a straight-through, twisted four-pair, Category 5e or better cable with an RJ45 connector into the port. Copper Ports To 10/100 ports 31795-M 2. Insert the other cable end into an RJ45 connector on the other device. Connect to a PoE Two expansion modules provide PoE capability: Expansion Module Port...
Page 114: Connect To Dual-Purpose Uplink Ports
Chapter 5 Install Stratix 8000 and 8300 Switches Connect to Dual-purpose The switches have two dual-purpose uplink ports. Each dual-purpose uplink port has a 10/100/1000 RJ45 connector for a copper interface and a slot for an SFP Uplink Ports module. Only one port of the dual-purpose port can be active at a time. If an SFP module port is connected, the SFP module port has priority.
Page 115: Connect To 100Basefx Ports
Install Stratix 8000 and 8300 Switches Chapter 5 Connect to 100BaseFX Ports ATTENTION: Class 1 laser product. Laser radiation is present when the system is open and interlocks bypassed. Only trained and qualified personnel are allowed to install, replace, or service this equipment. 1.
Page 116 Chapter 5 Install Stratix 8000 and 8300 Switches Notes: Rockwell Automation Publication 1783-UM007B-EN-P - March 2015...
Page 117 Configuration via Device Manager Configuration via the Studio 5000 Environment User Administration via Device Manager Configuration Files Secure Digital (SD) Card (Stratix 5700, ArmorStratix 5700, and Stratix 5400 switches) CompactFlash Memory Card (Stratix 8000/8300 switches) Firmware Updates Cisco Network Assistant...
Page 118: Get Started
• A straight-through or crossover Category 5 Ethernet cable to connect a computer to the switch For ArmorStratix 5700 switches, an M12-to-RJ45 patchcord, such as Allen-Bradley catalog number 1585D-M4TBJM-2, to connect a computer to the switch • For 1783-BMS4S2SGL or 1783-BMS4S2SGA switches: –...
Page 119 Get Started Chapter 6 To run Express Setup, follow these steps. 1. Make sure that at least one switch Ethernet port is available for Express Setup. For 1783-BMS4S2SGL and 1783-BMS4S2SGA switches, you must use IMPORTANT port Gi1/1 for Express Setup. Do not use the console port for Express Setup.
Page 120 Chapter 6 Get Started 4. Press and release the Express Setup button. Wait for a few seconds until the status indicator on one of the unconnected switch ports flashes green. This button is recessed 16 mm (0.63 in.) behind the panel. Use a small tool, such as a paper clip, to reach the button.
Page 121 Get Started Chapter 6 Stratix 8000/8300 Switch Express Setup Button Stratix 5400 Switch Express Setup Button Rockwell Automation Publication 1783-UM007B-EN-P - March 2015...
Page 122 Chapter 6 Get Started 5. Connect a Category 5 Ethernet cable (not provided) from the flashing switch port to the Ethernet port on a computer. If you wait too long to connect the cable, the Setup status indicator turns off. For 1783-BMS4S2SGL or 1783-BMS4S2SGA switches, do one of the following: •...
Page 123 Get Started Chapter 6 9. Complete the fields. To view fields for Common Industrial Protocol (CIP), you must click Advanced Settings. Rockwell Automation Publication 1783-UM007B-EN-P - March 2015...
Page 124 Chapter 6 Get Started Field Description Network Settings Host Name The name of the device. Management Interface (VLAN ID) The name and ID of the management VLAN through which the switch is managed. Choose an existing VLAN to be the management VLAN.
Page 125: Global Macro
• For a statically assigned IP address, change it to the previously configured IP address. 13. For Stratix 5400 switches, synchronize the SD card that came with the switch with the internal memory of the switch: • To synchronize the SD card via Device Manager, see page 145.
Page 126: Rslinx Software And Network Who Support
Chapter 6 Get Started RSLinx Software and The EtherNet/IP network interface also supports the List Identity command that is used by CIP-based network tools, such as the RSLinx® software RSWho Network Who Support function. RSWho enables you to locate and identify your switch on the network by using the electronic data sheet (EDS) files.
Page 127: Data Accessible With Cip
Get Started Chapter 6 Data Accessible with CIP The CIP interface lets you access the following information. Data Type Details Input data via I/O connection • Link status per port: not connected, connected • Unauthorized device per port: OK, not OK •...
Page 128: Configuration Via Device Manager
Chapter 6 Get Started Configuration via You can manage the switch by using Device Manager to configure and monitor the switch. Device Manager is a web-based management tool for configuring, Device Manager monitoring, and troubleshooting individual switches. Device Manager displays real-time views of switch configuration and performance.
Page 129 Get Started Chapter 6 To use Device Manager to configure and monitor the switch, follow these steps. 1. Launch a web browser on your workstation. 2. Enter the switch IP address in the web browser, and click Enter to display Device Manager.
Page 130: Configure Port Settings
Chapter 6 Get Started Configure Port Settings The basic port settings determine how data is received and sent between the switch and the attached device. You can change these settings to fit your network needs and to troubleshoot network problems. The settings on a switch port must be compatible with the port settings of the connected device.
Page 131 Get Started Chapter 6 Table 7 - Port Settings Field Description Port Name The number of the switch port, including port type, such as Fa for Fast Ethernet and Gi for Gigabit Ethernet, and the specific port number: • Gi/1 is the gigabit port 1 of the switch. •...
Page 132: Configuration Via The Studio 5000 Environment
Chapter 6 Get Started Configuration via the You can manage the switch by using the Logix Designer application in the Studio 5000 environment. The Logix Designer application is IEC 61131-3 Studio 5000 Environment compliant and offers relay ladder, structured text, function block diagram, and sequential function chart editors for you to develop application programs.
Page 133 Get Started Chapter 6 3. On the Select Module Type dialog box, select the switch and click Create. If you do not see the switch on the list, you can obtain the AOP from the Rockwell Automation support website: http://www.rockwellautomation.com/support/ Rockwell Automation Publication 1783-UM007B-EN-P - March 2015...
Page 134: Configure General Properties
Chapter 6 Get Started Configure General Properties To configure general properties, follow these steps. 1. In the navigation pane, click General and complete the fields. Be sure that the IP address and host name are the same as those provided IMPORTANT when you performed Express Setup.
Page 135 Get Started Chapter 6 2. In the Module Definition area, click Change. 3. On the Module Definition dialog box, complete the fields and click OK. Field Description Revision The major and minor revision of the switch: • Major revision: 1…128 •...
Page 136: Configure Connection Properties
Chapter 6 Get Started Configure Connection Properties In the navigation pane, click Connection. Table 9 - Connection Fields Field Description Requested Packet Interval (RPI) Enter a value between 300…5000. Inhibit Module Check to disable communication between the controller and the switch. Clear the checkbox to restore communication.
Page 137: Configure Switch Ip And Administrative Settings
Get Started Chapter 6 Configure Switch IP and Administrative Settings You can configure IP settings and administrative parameters. The IP address can be manually assigned (static) or it can be automatically assigned by a Dynamic Host Configuration Protocol (DHCP) server. The default is Static.
Page 138 Chapter 6 Get Started Figure 2 - Switch Configuration for Stratix 8000/8300 Switches Table 10 - Switch Configuration Fields Field Description (Stratix 5700 and ArmorStratix Click the method to use for assigning an IP address to the switch. switches) • Manually Configure IP settings •...
Page 139: Configure Port Settings
Get Started Chapter 6 Table 10 - Switch Configuration Fields (continued) Field Description Geographic Location (Optional). Enter a geographic location of the switch, up to 200 characters. The geographic location can include alphanumeric and special characters (dash and comma) and a carriage return. Spanning Tree Mode Spanning Tree Protocol (STP) on page 258.
Page 140 Chapter 6 Get Started Table 11 - Port Configuration Fields Field Description Unit Indicates where the port resides: (Stratix 8000/8300 • Base (for example, 1783-MS10T). switches) • Expansion module (for example, 1783-MX08T). Port The port selected for configuration. The port number includes the port type (Fa for Fast Ethernet and Gi for Gigabit Ethernet) and the specific port number.
Page 141: User Administration Via Device Manager
Get Started Chapter 6 User Administration via You can add, modify, or delete users and user login information for the switch via Device Manager. Device Manager From the Admin menu, choose Users. For each user, you can specify the information in Table Table 12 - Add User Fields Field...
Page 142: Configuration Files
Chapter 6 Get Started Configuration Files The switch configuration files (config.text and vlan.dat) are in ASCII human-readable format. This configuration file is stored in nonvolatile memory and is read into the switches’ Random Access Memory (RAM) as the running configuration when the switch is powered up. When any changes are made to the configuration, the changes immediately take effect in the running configuration.
Page 143: Manage Configuration Files Via The Logix Designer Application
Get Started Chapter 6 Manage Configuration Files via the Logix Designer Application You can do the following: • Save the switch configuration to a file for archiving • Restore a switch configuration stored locally on the computer or within the Logix Designer application project. Be prepared to enter a valid switch password to save and restore a switch configuration.
Page 144: Secure Digital (Sd) Card
ArmorStratix 5700, and Automation with the switches. Stratix 5400 switches) • Stratix 5400 switches ship with an SD card, which stores the initial configuration and firmware for the switches. ATTENTION: Rockwell Automation reserves the right to withhold support if a non-Rockwell SD card is used in Stratix switches.
Page 145: Synchronize The Sd Card Via Device Manager
Get Started Chapter 6 Synchronize the SD Card via Device Manager Use the Sync window to synchronize the SD card with the internal memory. On the Manual Sync tab, you can view the following: • Whether a card is present •...
Page 146 Chapter 6 Get Started Table 14 - Auto Sync Tab Fields Field Description Configuration Auto Sync—Automatically synchronize the configuration when a configuration change is made in Device Manager. Auto Sync is the default configuration. Prompt to Sync—After a configuration change, a message prompts you to confirm the synchronization.
Page 147: Synchronize The Sd Card Via The Logix Designer Application
Get Started Chapter 6 Synchronize the SD Card via the Logix Designer Application You can synchronize the SD card to either the configuration file or the entire image. In the navigation pane, click SD Flash Sync. Table 15 - SD Flash Sync Fields Field Description SD Flash Status...
Page 148: Compactflash Memory Card (Stratix 8000/8300 Switches)
Chapter 6 Get Started CompactFlash Memory Card The CompactFlash card for Stratix 8000/8300 switches contains the switch IOS operating system, Device Manager firmware, and user-defined configuration (Stratix 8000/8300 switches) settings. Without the CompactFlash card installed, the switch cannot power up or restart.
Page 149: Cisco Network Assistant
Get Started Chapter 6 With firmware revision 2.001 or later, the firmware is installed to the running nonvolatile memory location: • If you start the switch with the SD card inserted, the firmware is installed on the SD card. • If you start the switch from internal memory without the SD card inserted, the firmware is installed in the internal memory.
Page 150: Command Line Interface
Chapter 6 Get Started Command Line Interface You can manage the switch from the command line interface (CLI) by connecting your personal computer directly to the switch console port or through the network by using Telnet. Follow these steps to access the CLI through the console port. 1.
Page 151: Configure Switch Features
Port Mirroring Port Security Port Thresholds Power over Ethernet (PoE) Resilient Ethernet Protocol (REP) Layer 3 Routing (Stratix 8300 and Stratix 5400 Layer 3 firmware switches) Simple Network Management Protocol (SNMP) Smartports Spanning Tree Protocol (STP) Virtual Local Area Networks (VLANs) This chapter describes software features that you can configure via Device Manager, the Logix Designer application, or both.
Page 152: Alarms
Table 16 - Alarm Descriptions Switch Alarm Description Stratix 5400 switch The switch lets you connect two alarm inputs from external devices, such as a door or temperature gauge, to the alarm input port on the front panel of the switch.
Page 153 Configure Switch Features Chapter 7 Alarm Relay Settings You can configure the switch to trigger an external alarm device. The switch software is configured to detect faults that are used to energize the relay coil and change the state on both of the relay contacts. Normally open contacts close and normally closed contacts open.
Page 154 Chapter 7 Configure Switch Features Global Alarms From the Configure menu, choose Alarm Settings and click the Global tab. Table 17 - Global Tab Fields Field Description FCS Hysteresis (1-10) The frame check sequence (FCS) error hysteresis threshold is used to determine when an alarm condition is cleared. This value is expressed as a percentage of fluctuation from the FCS bit error rate.
Page 155 Configure Switch Features Chapter 7 Port Alarms From the Configure menu, choose Alarm Settings and click the Port tab. For each port, choose an Alarm Profile and set the FCS threshold. The frame check sequence (FCS) error hysteresis threshold is expressed as a percentage of fluctuation from the FCS bit error rate.
Page 156 Chapter 7 Configure Switch Features On the Add/Edit Profile Instance window, you can configure the alarms and actions for an alarm profile. Table 18 - Add/Edit Profile Instance Fields Field Description Name A unique name for the alarm profile. Alarm Name These types of alarms can trigger an action.
Page 157: Cip Sync Time Synchronization (Precision Time Protocol)
Configure Switch Features Chapter 7 CIP Sync Time The IEEE 1588 standard defines Precision Time Protocol (PTP). The protocol enables precise synchronization of clocks in measurement and control systems. Synchronization We refer to this feature as CIP Sync time synchronization. The clocks are (Precision Time Protocol) synchronized with nanosecond accuracy over the EtherNet/IP communication network.
Page 158: Configure Time Synchronization Via The Device Manager
Chapter 7 Configure Switch Features Configure Time Synchronization via the Device Manager From the Configure menu, choose PTP. Once you choose a mode, you can edit the settings for each port. The parameters depend on the selected mode. You can configure per-port PTP when the switch is in Boundary mode or End-to-end Transparent mode.
Page 159 Configure Switch Features Chapter 7 Table 19 - PTP Fields (continued) Field Description State (Boundary mode only). The synchronization state on the switch port with the parent or Grandmaster clock: • Listening—The switch port is waiting while a parent or Grandmaster clock is selected. •...
Page 160: Logix Designer Application
Chapter 7 Configure Switch Features Configure Time Synchronization via the Logix Designer Application In the navigation pane, click Time Sync Configuration. Figure 3 - Time Sync Configuration for Stratix 5700, ArmorStratix 5700, and Stratix 8000/8300 Switches Table 20 - Time Sync Configuration Fields for Stratix 5700, ArmorStratix 5700, and Stratix 8000/8300 Switches Field Description Unit (Stratix 8000/8300 switches)
Page 161 Configure Switch Features Chapter 7 Table 20 - Time Sync Configuration Fields for Stratix 5700, ArmorStratix 5700, and Stratix 8000/8300 Switches (continued) Field Description Enable Check to enable the configuration of the port on the device. Clear the checkbox to disable the port configuration on the device. The Port Enable feature appears dimmed when the Switch PTP Enable checkbox is cleared.
Page 162 Chapter 7 Configure Switch Features Figure 4 - Time Sync Configuration for Stratix 5400 Switches Table 21 - Time Sync Configuration Fields for Stratix 5400 Switches Field Description Enable Time Synchronization Check to enable time synchronization on the device. By default, time synchronization is enabled on all of the Fast Ethernet and Gigabit Ethernet ports on the switch.
Page 163: View Time Sync Information In The Logix Designer Application
Configure Switch Features Chapter 7 View Time Sync Information in the Logix Designer Application In the navigation pane, click Time Sync Information. The Time Sync Information view shows current information about the real-time clocks in the network. The CIP Time Synchronization protocol provides a standard mechanism to synchronize clocks across a network of distributed devices.
Page 164 Chapter 7 Configure Switch Features Figure 6 - Time Sync Information for Stratix 5400 Switches Table 22 - Time Sync Information Fields Field Description CIP Sync Time Synchronization Displays whether the Precision Time Protocol is enabled or disabled on the device.
Page 165: Cryptographic Ios Software
Configure Switch Features Chapter 7 Table 22 - Time Sync Information Fields Field Description Accuracy Indicates the expected absolute accuracy of the local clock relative to CIP Sync time synchronization epoch (31 December, 1969 23:59:51.99918 UTC). The accuracy is specified as a graduated scale starting at 25 ns and ending at greater than 10 seconds or unknown. For example, a GPS time source has an accuracy of approximately 250 ns.
Page 166: Device-Level Ring (Dlr)
Chapter 7 Configure Switch Features Device-level Ring (DLR) DLR is available only on certain models of Stratix 5700 and ArmorStratix 5700 switches. For specific catalog numbers, see page A DLR network is a single-fault-tolerant ring network that is intended for the interconnection of automation devices without the need for more switches.
Page 167: Dlr Port Choices
Configure Switch Features Chapter 7 A DLR network includes the following nodes. Node Description Supervisor node A DLR network requires at least one node to be configured as ring supervisor. IMPORTANT: By default, the supervisor function is disabled on supervisor-capable devices, so they are ready to participate in a linear network or as a ring node on a DLR network.
Page 168: Dlr Considerations
Chapter 7 Configure Switch Features DLR Considerations Depending on your network architecture, DLR topology limitations can exist. IMPORTANT Make sure to validate your DLR topology within the larger network prior to production use. Some switch capabilities are not supported on DLR-enabled ports. Unsupported capabilities include, but are not limited to, the following: •...
Page 169 Configure Switch Features Chapter 7 Table 23 - DLR Fields Field Description Mode Choose one of these modes: • Disabled—The DLR feature is disabled on the switch. • Node—The switch is a ring node. • Supervisor—The switch is a ring supervisor. Disabled is the default mode.
Page 170: Configure Dlr Via The Logix Designer Application
Chapter 7 Configure Switch Features Configure DLR via the Logix Designer Application In the navigation pane, click Device Level Ring (DLR). Table 24 - Device Level Ring (DLR) Fields Field Description Enable Ring 1 Check to enable DLR on the ports specified in the Port 1 and Port 2 fields. Port 1 Choose a ring port.
Page 171 Configure Switch Features Chapter 7 Table 25 - Ring 1 Fields Field Description Network Topology Displays whether the switch is operating in a DLR or linear network. Valid values: • Ring • Linear Network Status Displays the current status of the network. Valid values: •...
Page 172 Chapter 7 Configure Switch Features Table 26 - Advanced Network Configuration Fields Field Description Network Topology Displays whether the switch is operating in a DLR or linear network. Valid values: • Ring • Linear Active Ring Supervisor Displays the IP address of the active ring supervisor. Active Supervisor Precedence Displays the precedence currently assigned to the active ring supervisor.
Page 173 Configure Switch Features Chapter 7 The Members dialog box displays each device in the ring only when the switch is the ring supervisor. Otherwise, no devices are listed. Table 27 - Members Fields Field Description Ring Member Displays the order of devices in the ring when the switch is the ring supervisor. The switch is always ring member 1.
Page 174: Dynamic Host Configuration Protocol (Dhcp) Persistence
Chapter 7 Configure Switch Features Dynamic Host Configuration Every device in an IP-based network must have a unique IP address. DHCP assigns IP address information from a pool of available addresses to newly Protocol (DHCP) Persistence connected devices (DHCP clients) in the network. If a device leaves and then rejoins the network, the device receives the next available IP address, which can or cannot be the same address that it had before.
Page 175 Configure Switch Features Chapter 7 4. To reserve an address pool to only the devices that are specified in the DHCP persistence table, check the Reserved Only checkbox in the DHCP pool table. DHCP requests from ports not in the persistence table or from another switch are ignored.
Page 176 Chapter 7 Configure Switch Features 3. Complete the fields and click OK. Field Description DHCP Pool Name The name of the DHCP IP address pool that is configured on the switch. The name can have up to 31 alphanumeric characters. The name cannot contain a ? or a tab.
Page 177 Configure Switch Features Chapter 7 Reserve IP Addresses through DHCP Persistence You can reserve and preassign an IP address from the IP address pool to a specific switch port. As a result, a device that is connected to that switch port always receives the same IP address regardless of its MAC address.
Page 178 Chapter 7 Configure Switch Features The following figure and table illustrate DHCP persistence behavior. Switch 1 Switch 2 Table 28 - DHCP Persistence Behavior Then • Switch 1 has ports FA1…FA3 in its persistence table A new device that is connected to switch 1 FA1 receives an IP address from the switch 1 persistence table. A •...
Page 179: Configure Dhcp Via The Logix Designer Application
Configure Switch Features Chapter 7 Configure DHCP via the Logix Designer Application In the navigation pane, click DHCP Address Assignment. You can assign a specific IP address to each port, so that the device attached to a given port receives the same IP address. Table 30 - DHCP Address Assignment Fields Field Description...
Page 180: Etherchannels
Chapter 7 Configure Switch Features EtherChannels An EtherChannel, or port group, is a group of two or more Fast Ethernet or Gigabit Ethernet switch ports that are bundled into a logical link. The group creates a higher bandwidth link between two switches. For example, four 10/100 switch ports can be assigned to an EtherChannel to provide full-duplex bandwidth of up to 800 Mb/s.
Page 181 Configure Switch Features Chapter 7 Figure 8 shows two EtherChannels. Two full-duplex 10/100/1000-Mbps ports on Switches A and C create an EtherChannel with a bandwidth of up to 4 Gbps between both switches. Similarly, two full-duplex 10/100 ports on Switches B and D create an EtherChannel with a bandwidth of up to 400 Mbps between both switches.
Page 182: Configure Etherchannels Via Device Manager
Chapter 7 Configure Switch Features Configure EtherChannels via Device Manager From the Configure menu, choose EtherChannels. Table 31 - EtherChannel Fields Field Description Channel Group Number A number from 1 to 6 that identifies this EtherChannel. You can configure as many as six EtherChannels. Channel Mode Determines how ports become active.
Page 183: Internet Group Management Protocol (Igmp) Snooping With Querier
Table 32 - Default Supported Multicast Groups Switch Default Multicast Groups Stratix 5400 switches 1024 Stratix 5700 and ArmorStratix 5700 switches If you exceed 180 multicast groups, we recommend that you switch to the routing SDM template via Device Manager.
Page 184: Configure Igmp Snooping Via Device Manager
Chapter 7 Configure Switch Features Configure IGMP Snooping via Device Manager From the Configure menu, choose IGMP Snooping: • To enable IGMP Snooping for all VLAN IDs, check Enable next to IGMP Snooping. • To enable IGMP Querier for all VLAN IDs, check Enable next to IGMP Querier.
Page 185: Network Address Translation (Nat)
Configure Switch Features Chapter 7 Network Address Translation For a list of switches that support NAT, see page (NAT) NAT is a service that translates one IP address to another IP address via a NAT-configured switch. The switch translates the source and destination addresses within data packets as traffic passes between subnets.
Page 186 Chapter 7 Configure Switch Features • If traffic is routed through a Layer 2 switch (Figure 10), you define the following: – A private-to-public translation for each device on the private subnet that communicates on the public subnet. – A public-to-private translation for each device on the public subnet that communicates on the private subnet.
Page 187 Configure Switch Features Chapter 7 Figure 10 - Layer 2 Example HMI 10.10.1.101 Line Controller (LC) VLAN 10 VLAN 10 10.10.1.100 192.168.100 C1 to LC Layer 2 Device (Stratix 8000) VLAN 10: 10.10.1.1 C2 to LC VLAN 10 VLAN 10 Machine 1 (M1) Ma Mach chin ine e 1 1 (M (M 1) 1)
Page 188 Chapter 7 Configure Switch Features An address translation can be one of three types. The type of translation determines the number of translation entries. A switch can have a maximum of 128 translation entries. Table 33 - Number of Translation Entries by Translation Type Translation Translation Description...
Page 189: Vlan Assignments
Configure Switch Features Chapter 7 VLAN Assignments When configuring NAT, you can assign one or more VLANs to a NAT instance. When you assign a VLAN to a NAT instance, the traffic that is associated with that VLAN is subject to the configuration parameters of the NAT instance. Configuration parameters include whether traffic is translated, fixed up, blocked, or passed through.
Page 190: Configuration Considerations
Chapter 7 Configure Switch Features Configuration Considerations Consider these guidelines and limitations when configuring NAT: • A switch can translate only IPv4 addresses. • A switch can have a maximum of 128 NAT instances, 128 NAT-associated VLANs, and 128 translation entries. A subnet translation counts as only one translation entry, but includes translations for many devices.
Page 191: Configure Nat Via Device Manager
Configure Switch Features Chapter 7 Configure NAT via Device Manager To configure NAT, follow one of these procedures that are based on your application: • Create NAT Instances for Traffic Routed through a Layer 3 Switch or Router For an example of this application, see Figure 9 on page 186.
Page 192 Chapter 7 Configure Switch Features 2. Click Add to display the General tab of the Add/Edit NAT Instance window. 3. In the Name field, type a unique name to identify the instance. The instance name cannot include spaces or exceed 32 characters. 4.
Page 193 Configure Switch Features Chapter 7 5. In the Private to Public area, click Add Row, complete the fields, and click Save. Field Description Private IP Address Type a private IP address: • To translate one address, type the existing address for the device on the private subnet. •...
Page 194 Chapter 7 Configure Switch Features Field Description Type Choose one of these values: • Single—Translate one address. • Range—Translate a range of addresses. • Subnet—Translate all addresses in the private subnet or a portion of the private subnet. Range Type the number of addresses to translate. This field is available only if you choose Range in the Type field. Valid values: 1…128 Default value = 1 IMPORTANT: Each address in the range counts as one translation entry.
Page 195 Configure Switch Features Chapter 7 2. Click Add to display the General tab of the Add/Edit NAT Instance window. 3. In the Name field, type a unique name to identify the instance. The instance name cannot include spaces or exceed 32 characters. 4.
Page 196 Chapter 7 Configure Switch Features Field Description Private IP Address Type a private IP address: • To translate one address, type the existing address for the device on the private subnet. • To translate a range of addresses, type the first address in the range of sequential addresses. •...
Page 197 Configure Switch Features Chapter 7 Field Description Type Choose one of these values: • Single—Translate one address. • Range—Translate a range of addresses. • Subnet—Translate all addresses in the private subnet or a portion of the private subnet. Range Type the number of addresses to translate. This field is available only if you choose Range in the Type field. Valid values: 1…128 Default value = 1 IMPORTANT: Each address in the range counts as one translation entry.
Page 198 Chapter 7 Configure Switch Features 7. Click Add Row, complete the fields, and click Save. Field Description Public IP Address Type a public IP address: • To translate one address, type the existing address for the device on the public subnet. •...
Page 199 Configure Switch Features Chapter 7 Field Description Type Choose one of these values: • Single—Translate one address. • Range—Translate a range of addresses. • Subnet—Translate all addresses in the public subnet or a portion of the public subnet. Range Type the number of addresses to translate. This field is available only if you choose Range in the Type field. Valid values: 1…128 Default value = 1 IMPORTANT: Each address in the range counts as one translation entry.
Page 200: Configure Nat Via The Logix Designer Application
Chapter 7 Configure Switch Features 2. Choose one of these options for incoming and outgoing packets that are not handled by NAT: • Pass-through—Permit the packets to pass across the NAT boundary. • Blocked—Drop the packets. 3. In the Fix up Packets area, check or clear the checkboxes to enable or disable fixups for ARP and ICMP.
Page 201 Configure Switch Features Chapter 7 Table 34 - NAT Fields (continued) Field Description Global Diagnostics Current Active Translations Displays the total number of translations that occurred within the last 90 seconds across all NAT instances. Total Translations Displays the total number of translations across all NAT instances. Total Translated Packets Displays the total number of translated packets across all NAT instances.
Page 202 Chapter 7 Configure Switch Features Create NAT Instances for Traffic Routed through a Layer 3 Switch or Router To create a NAT instance for traffic that is routed through a Layer 3 switch or router, follow these steps. 1. From the NAT view, click New Instance to display the General tab. 2.
Page 203 Configure Switch Features Chapter 7 4. Click New Entry to display the New Entry dialog box. 5. Do one of the following: • To translate one address for a device on the private subnet that communicates on the public subnet, complete these fields. Field Description Type of Entry...
Page 204 Chapter 7 Configure Switch Features Field Description Range Type the number of addresses to include in the range. Valid values: 1…128 Default value = 1 IMPORTANT: Each address in the range counts as one translation entry. The switch supports a maximum of 128 translation entries. Effective Private Addresses Displays the range of existing addresses for devices on the private subnet that are configured for translation.
Page 205 Configure Switch Features Chapter 7 Field Description Subnet Mask From the pull-down menus, choose the subnet mask for the addresses to translate. Valid values: • Class B: 255.255.0.0 • Class C: 255.255.255.0 • Portion of Class C: – 255.255.255.128 (provides 128 addresses per translation entry –...
Page 206 Chapter 7 Configure Switch Features Create NAT Instances for Traffic Routed through a Layer 2 Switch To create a NAT instance for traffic that is routed through a Layer 2 switch, follow these steps. 1. From the NAT view, click New Instance to display the General tab. 2.
Page 207 Configure Switch Features Chapter 7 4. Click New Entry to display the New Entry dialog box. 5. Do one of the following: • To translate one address for a device on the private subnet that communicates on the public subnet, complete these fields. Field Description Type of Entry...
Page 208 Chapter 7 Configure Switch Features • To translate a range of addresses for devices on the private subnet that communicates on the public subnet, complete these fields. Field Description Type of Entry Choose Range. Starting Private IP Address Type the existing starting address for the device on the private subnet. Starting Public IP Address Type a unique, starting public address to represent the devices.
Page 209 Configure Switch Features Chapter 7 Field Description Starting Public IP Type a unique, starting public address to represent the devices. This address must Address correspond to the size of the subnet mask to translate. Subnet Mask Starting Public Subnet Address 255.255.0.0 The last two octets must end in 0.
Page 210 Chapter 7 Configure Switch Features 8. Click New Entry to display the New Entry dialog box. Rockwell Automation Publication 1783-UM007B-EN-P - March 2015...
Page 211 Configure Switch Features Chapter 7 9. Do one of the following: • To translate one address for a device on the public subnet that communicates on the private subnet, complete these fields. Field Description Type of Entry Choose Single. Single is the default value. Starting Public IP Address Type the existing address for the device on the public subnet.
Page 212 Chapter 7 Configure Switch Features • To translate all addresses in the public subnet or a portion of the public subnet, complete these fields. Field Description Type of Entry Choose Subnet. Starting Public IP Type the existing starting address for a device on the public subnet. This address Address must correspond to the size of the subnet mask to translate.
Page 213 Configure Switch Features Chapter 7 Field Description Subnet Mask From the pull-down menus, choose the subnet mask for the addresses to translate. Valid values: • Class B: 255.255.0.0 • Class C: 255.255.255.0 • Portion of Class C: – 255.255.255.128 (provides 128 addresses per translation entry –...
Page 214 Chapter 7 Configure Switch Features 2. In the Traffic Permits table, choose one of these options for unsupported incoming and outgoing packets: • Pass-Through—Permit the packets to pass across the NAT boundary. • Blocked—Drop the packets. 3. In the Fix-up Packets area, check or clear the checkboxes to enable or disable protocol fixups for ARP and ICMP.
Page 215: Port Mirroring
Configure Switch Features Chapter 7 Port Mirroring Port mirroring is for advanced users with experience in troubleshooting traffic and protocol issues on networks. Port mirroring copies, or mirrors, traffic on one port to a monitoring port where a network protocol analyzer tool can capture the packet.
Page 216: Static Secure Mac Address (Mac Id)
Chapter 7 Configure Switch Features The following table shows the Smartport role and the maximum number of supported MAC IDs. Table 35 - Maximum Number of MAC IDs per Smartport Role Smartport Role Number of MAC IDs (max) Automation Device Desktop for Automation Switch for Automation Not restricted...
Page 217: Configure Port Security Via Device Manager
Configure Switch Features Chapter 7 Configure Port Security via Device Manager From the Configure menu, choose Port Security. Port security limits and identifies the MAC addresses of devices that can send traffic through the switch port. The switch port does not forward traffic from devices outside the defined group of devices.
Page 218 Chapter 7 Configure Switch Features To change the Static MAC Addresses table for a port, do the following: 1. Click the radio button next to the port to configure. 2. Click Edit. 3. Clear or check the Enable checkbox. 4. Configure MAC addresses as follows: •...
Page 219: Configure Port Security Via The Logix Designer Application
For Stratix 5400, Stratix 5700, and ArmorStratix 5700 switches, in the navigation pane, click Port Security. Figure 12 - Port Security for Stratix 5400, Stratix 5700, and ArmorStratix 5700 Switches Table 36 - Port Security Fields for Stratix 5400, Stratix 5700, and ArmorStratix 5700 Switches Field Description Port The port on which you want to enable or disable security.
Page 220 Chapter 7 Configure Switch Features For Stratix 8000/8300 switches, in the navigation pane, click Advanced Port Configuration. Figure 13 - Advanced Port Configuration for Stratix 8000/8300 Switches Table 37 - Advanced Port Configuration Fields for Stratix 8000/8300 Switches Field Description Unit Indicates where the port resides: •...
Page 221: Port Thresholds
Configure Switch Features Chapter 7 Port Thresholds Port thresholds prevent traffic on a LAN from being disrupted by a broadcast, multicast, or unicast storm on one of the physical interfaces. Port thresholds do not apply to switches with lite firmware. A LAN storm occurs when packets flood the LAN, creating excessive traffic and degrading network performance.
Page 222: Outgoing (Rate Limiting)
Chapter 7 Configure Switch Features Figure 14 - Port Thresholds Example Forwarded Traffic Blocked Traffic Total Number of Broadcast Threshhold Packets or Bytes Time The combination of the storm-control suppression level and the 1-second time interval controls the way the port thresholds algorithm works. A higher threshold enables more packets to pass through.
Page 223: Configure Port Thresholds Via Device Manager
Configure Switch Features Chapter 7 Configure Port Thresholds via Device Manager From the Configure menu, choose Port Thresholds. Table 38 - Port Threshold Fields Field Description Incoming Unicast For each port, do the following: 1. Check or clear the Enable checkbox. Multicast 2.
Page 224: Configure Port Thresholds Via The Logix Designer Application
Figure 15 - Port Thresholds for Stratix 5400, Stratix 5700, and ArmorStratix 5700 Switches Table 39 - Port Threshold Fields for Stratix 5400, Stratix 5700, and ArmorStratix 5700 Switches Field Description Port The port selected for configuration.
Page 225 Configure Switch Features Chapter 7 Figure 16 - Port Thresholds for Stratix 8000/8300 Switches Table 40 - Port Threshold Fields for Stratix 8000/8300 Switches Field Description Unit Indicates where the port resides: • Base (for example, 1783-MS10T) • Expansion module (for example, 1783-MX08T) Port Indicates the port that is selected for configuration.
Page 226: Power Over Ethernet (Poe)
Chapter 7 Configure Switch Features Power over Ethernet (PoE) Switches and expansion modules with PoE ports are software-configurable and provide these features: • Support for IEEE 802.3af (PoE)-compliant devices. • Support for IEEE 802.3at Type 2 (PoE+), which increases the available power that can be drawn by powered devices from 15.4…30 W per port.
Page 227: Powered Device Detection And Initial Power Allocation
Configure Switch Features Chapter 7 When you make PoE configuration changes to a port, the port drops power. IMPORTANT Whether the port powers up again depends on the new configuration, the state of the other PoE ports, and the state of the power budget. For example, if port 1 is in Auto mode and the On state, and you configure it for Static mode, the switch removes power from port 1, detects the powered device, and repowers the port.
Page 228: Power Management Modes
Chapter 7 Configure Switch Features The switch monitors and tracks requests for power and grants power only when it is available. The switch tracks its power budget, which is the amount of power available on each PoE port. The switch performs power-accounting calculations when a port is granted or denied power to keep the power budget up to date.
Page 229 Configure Switch Features Chapter 7 If a powered device is removed, the switch automatically detects the disconnect and removes power from the port. You can connect a nonpowered device without damaging it. You can specify the maximum wattage that is allowed on the port. If the IEEE-class maximum wattage of the powered device is greater than the configured maximum value, the switch does not provide power to the port.
Page 230 Chapter 7 Configure Switch Features With PoE+, if you do not manually configure the cutoff-power value, the switch determines it by using one of the following: • The device IEEE classification and LLDP power negotiation • CDP power negotiation with a Cisco end device If CDP or LLDP are not enabled, the default value of 30 W is applied.
Page 231: Configure Poe Ports Via Device Manager
Configure PoE Ports via Device Manager From the Configure menu, choose Power Management. Figure 17 - PoE Configuration for Stratix 5400, Stratix 5700, and ArmorStratix 5700 Switches Figure 18 - PoE Configuration for Stratix 8000/8300 Switches Rockwell Automation Publication 1783-UM007B-EN-P - March 2015...
Page 232 Chapter 7 Configure Switch Features Table 42 - Power Management Fields Field Description Selected Module Choose a connected PoE module for which to view status information: (Stratix 8000/8300 switches) • 2—Module in the left position • 3—Module in the right position Total Power Supported To limit the total PoE power budget, type an appropriate value that is based on the power source: •...
Page 233: Configure Poe Via The Logix Designer Application
Configure PoE via the Logix Designer Application In the navigation pane, click PoE. Figure 19 - PoE Configuration for Stratix 5400, Stratix 5700, and ArmorStratix 5700 Switches Figure 20 - PoE Configuration for Stratix 8000/8300 Switches Rockwell Automation Publication 1783-UM007B-EN-P - March 2015...
Page 234 Chapter 7 Configure Switch Features Table 43 - PoE Fields Field Description Power over Ethernet (PoE) Port Configuration Port Displays the port number. Mode Displays the Power Management mode of the port: • Auto—Enables the detection of powered devices and automatically allocates power to the PoE port if a device is connected. This setting is selected by default.
Page 235: Resilient Ethernet Protocol (Rep)
Configure Switch Features Chapter 7 Resilient Ethernet Protocol REP provides an alternative to Spanning Tree Protocol (STP) to control network rings and loops, handle link failures, and improve convergence time. REP (REP) controls a group of ports that are connected in a segment, makes sure that the segment does not create any bridging loops, and responds to link failures within the segment.
Page 236: Rep Open Segment
Chapter 7 Configure Switch Features REP and STP can coexist on the same switch, but not on the same port. REP does not interact with STP. For example, if a port is configured as an REP port, STP is disabled on that port. STP bridge protocol data units (BPDUs) are not accepted on or sent from REP ports.
Page 237: Rep Ring Segment
Configure Switch Features Chapter 7 REP Ring Segment The segment that is shown in Figure 22, with both edge ports on the same switch, is a ring segment. In this configuration, there is connectivity between the edge ports through the segment. With this configuration, you can create a redundant connection between any two switches in the segment.
Page 238: Link Integrity
Chapter 7 Configure Switch Features In the example that is shown in Figure 23, E1 or E2 can be configured as the primary no-neighbor port. Figure 23 - Ring Topology Example REP Not Supported REP Ports Configured at Transit Ports REP has these limitations: •...
Page 239: Configure Rep Via Device Manager
Configure Switch Features Chapter 7 Configure REP via Device Manager From the Configure menu, choose REP. To create a REP segment, set a segment ID and port type for a switch port. Table 44 - REP Fields Field Description REP Admin VLAN The administrative VLAN.
Page 240: Layer 3 Routing (Stratix 8300 And Stratix 5400 Layer 3 Firmware Switches)
TCNs are used within the segment to notify REP neighbors of topology changes. At the edge of the segment, REP can propagate the notification to the STP or to the other REP segments. Stratix 8300 switches and Stratix 5400 Layer 3 firmware models use IP address Layer 3 Routing routing to map subnetworks (subnets) to an individual VLAN.
Page 241: Types Of Routing
Configure Switch Features Chapter 7 Types of Routing Stratix 8300 switches can route packets by using these methods. Table 45 - Routing Feature Description Static and connected routing Static and Connected Routing on page 242. Dynamic routing Dynamic routing protocols are used by Layer 3 switches to calculate dynamically the best route for forwarding traffic. There are two types of dynamic routing protocols: •...
Page 242: Static And Connected Routing
Chapter 7 Configure Switch Features Static and Connected The switch supports these forms of routing: Routing • Static routing—Defines explicit paths between two devices (routers and switches). You must manually define the route information, including the destination IP address, destination subnet mask, and next hop router IP address.
Page 243: Reallocate Switch Memory For Routing Via Device Manager
Configure Switch Features Chapter 7 Reallocate Switch Memory for Routing via Device Manager Switch Management Database (SDM) templates optimize how switch memory is allocated for specific features, such as routing. To enable routing, you must change the default SDM template to the Lanbase Routing template. To apply an SDM template, follow these steps.
Page 244: Enable And Configure Routing Via Device Manager
From the Routing window, you can enable connected routing only or both static and connected routing. When static routing is enabled, connected routing is enabled by default. For more information about these routing types, refer to Layer 3 Routing (Stratix 8300 and Stratix 5400 Layer 3 firmware switches) on page 240.
Page 245: Simple Network Management Protocol (Snmp)
Configure Switch Features Chapter 7 Simple Network The switch supports SNMP versions 1, 2C, and 3. SNMP enables the switch to be remotely managed through other network management software. This feature Management Protocol is disabled by default. (SNMP) SNMP is based on three concepts: •...
Page 246: Supported Mibs
Chapter 7 Configure Switch Features Supported MIBs Stratix managed switches support the following MIBs. Table 46 - Supported MIBs MIB Name BRIDGE-MIB CISCO-MEMORY-POOL-MIB IP-MIB CALISTA-DPA-MIB CISCO-PAE-MIB LLDP-EXT-MED-MIB CISCO-ACCESS-ENVMON-MIB CISCO-PAGP-MIB LLDP-MIB CISCO-ADMISSION-POLICY-MIB CISCO-PING-MIB NETRANGER CISCO-AUTH-FRAMEWORK-MIB CISCO-PORT-QOS-MIB NOTIFICATION-LOG-MIB CISCO-BRIDGE-EXT-MIB CISCO-PORT-SECURITY-MIB OLD-CISCO-CHASSIS-MIB CISCO-BULK-FILE-MIB CISCO-PORT-STORM-CONTROL-MIB OLD-CISCO-CPU-MIB CISCO-CABLE-DIAG-MIB...
Page 247: Configure Snmp Via Device Manager
Configure Switch Features Chapter 7 Configure SNMP via Device Manager From the Configure menu, choose SNMP. Community strings are passwords to the switch Management Information Base (MIB). You can create community strings that provide a remote manager read-only or read-write access to the switch. To create, modify, and delete community strings, click the Community Strings tab.
Page 248: Use Snmp Management Applications
Chapter 7 Configure Switch Features Use SNMP Management Applications You can use SNMP management applications such as IntraVue or HP OpenView to configure and manage the switch. Refer to Simple Network Management Protocol (SNMP) on page 245 for more information. Smartports Smartports are recommended configurations for the switch ports.
Page 249: Custom Smartport Roles
CS1…CS10 Custom Smartport roles. You can create a customized port role with a user-defined name. See Custom Smartport Roles (Stratix 5400, Stratix 5700, and ArmorStratix 5700 switches) on page 249. Custom Smartport Roles (Stratix 5400, Stratix 5700, and ArmorStratix 5700 switches) You can create and modify as many as 10 custom Smartport roles for a variety of custom applications.
Page 250: Configure Smartports Via Device Manager
Chapter 7 Configure Switch Features Configure Smartports via Device Manager From the Configure menu, choose Smartports. Follow these guidelines when using Smartport roles: • Before using Smartport roles, decide which switch port is connected to which device type. • Before attaching a device to the port or reconnecting devices that have been moved, verify which Smartport role is applied to a port.
Page 251: Customize Port Role Attributes
Configure Switch Features Chapter 7 Customize Port Role Attributes Each switch port is a member of a VLAN. Devices that are attached to switch ports that belong to the same VLAN share data broadcasts and system resources. Depending on your network requirements, it can be sufficient to assign all ports to the default VLAN, which is named default.
Page 252: Manage Custom Smartport Macros (Stratix 5400, Stratix 5700, And Armorstratix 5700 Switches)
5. Click Submit. Manage Custom Smartport Macros (Stratix 5400, Stratix 5700, and ArmorStratix 5700 switches) To create a custom Smartports macro for a Stratix 5400, Stratix 5700, or ArmorStratix 5700 switch, follow these steps. 1. Click the Custom Smartports tab.
Page 253 Configure Switch Features Chapter 7 5. Enter a macro definition. The definition can contain up to 3000 characters. Enter the macro commands with one command per line. Use the # character at the beginning of a line to enter comment text within the macro. Available parameters for the macro are $native_vlan, $access_vlan, and $voice_vlan.
Page 254 Chapter 7 Configure Switch Features 4. Click Edit. 5. Change the definitions as needed. 6. Click Submit. Delete a Custom Smartports Macro You cannot delete a custom Smartports macro that is currently in use. 1. From the Configure menu, choose Smartports. 2.
Page 255 Configure Switch Features Chapter 7 Import a Custom Smartports Macro 1. From the Configure menu, choose Smartports. 2. Click the Custom Smartports tab. 3. Click Import. 4. Click Browse. 5. Select the macro file on your computer or network drive. The file must be an appropriately formatted .xml file.
Page 256: Assign Smartports And Vlans Via The Logix Designer Application
For Stratix 5400, Stratix 5700, and ArmorStratix 5700 switches, in the navigation pane, click Smartports & VLANs. Figure 25 - Smartport & VLAN Assignment for Stratix 5400, Stratix 5700, and ArmorStratix 5700 Switches Rockwell Automation Publication 1783-UM007B-EN-P - March 2015...
Page 257 Configure Switch Features Chapter 7 For Stratix 8000/8300 switches, in the navigation pane, click Advanced Port Configuration. Figure 26 - Advanced Port Configuration for Stratix 8000/8300 Switches Table 48 - Smartport and VLAN Assignment Fields Field Description Unit Indicates where the port resides: •...
Page 258: Spanning Tree Protocol (Stp)
Chapter 7 Configure Switch Features Spanning Tree Protocol (STP) STP is a Layer 2 link management protocol that provides path redundancy while preventing loops in the network. For a Layer 2 Ethernet network to function properly, only one active path can exist between any two stations. Multiple active paths among end stations cause loops in the network.
Page 259: Configure Stp Via Device Manager
Configure Switch Features Chapter 7 • Rapid Per VLAN Spanning Tree Plus (RPVST+) immediately deletes dynamically learned MAC address entries upon receiving a topology change. By contrast, PVST+ uses a short aging time for dynamically learned MAC addresses. We recommend that you leave STP enabled to prevent network loops and provide a redundant path if the active path becomes unavailable.
Page 260 Chapter 7 Configure Switch Features PortFast Settings To enable PortFast and related features, click the PortFast tab. On the PortFast tab, you can change the way that STP is implemented on individual ports. PortFast features are typically enabled only on access ports. Access ports connect to devices such as personal computers, access points, and servers that are not expected to send bridge protocol data units (BPDUs).
Page 261: Configure Stp Via The Logix Designer Application
• Rapid Spanning Tree Protocol/Multiple Spanning Tree (RSTP/MST) • Per VLAN Spanning Tree Plus (PVST+) • Rapid Per-VLAN Spanning Tree (RPVST+) MST/RSTP is the default. Figure 27 - Switch Configuration for Stratix 5400, Stratix 5700, and ArmorStratix 5700 Switches Rockwell Automation Publication 1783-UM007B-EN-P - March 2015...
Page 262: Virtual Local Area Networks (Vlans)
We recommend that you first determine your VLAN needs before creating VLANs. With custom Smartports available on Stratix 5400, Stratix 5700, and ArmorStratix 5700 switches, you can specify the type of VLAN you want to implement on that port.
Page 263: Isolate Traffic And Users
Configure Switch Features Chapter 7 Isolate Traffic and Users By using VLANs, you can isolate different types of traffic, such as voice and data. Isolating different types of traffic helps to preserve the quality of the transmission and to minimize excess traffic among the logical segments. You can also use VLANs to isolate different types of users.
Page 264: Isolate Different Traffic Types
Chapter 7 Configure Switch Features Isolate Different Traffic Types Isolating data traffic from delay-sensitive traffic, such as voice traffic, increases the quality of the voice transmission. In Figure 28, switch ports that are connected to the IP phones belong to VLAN 3, a VLAN that is configured to provide Voice over IP (VoIP) services on these connections, meaning priority is given to voice traffic over regular IP data traffic.
Page 265: Configure Vlans Via Device Manager
Configure Switch Features Chapter 7 Configure VLANs via Device Manager From the Configure menu, choose VLAN Management. You can add, edit, and delete VLANs. To assign ports to VLANs, use the Edit Physical Ports window, as described on page 130. Before you assign ports to VLANs, make sure that each port has the appropriate port role.
Page 266: Configure Vlans Via The Logix Designer Application
In the navigation pane, click Smarports & VLANs. In the VLAN Configuration area, you can add, edit, and delete VLANs. Figure 29 - VLAN Configuration for Stratix 5400, Stratix 5700 and ArmorStratix 5700 Switches To assign ports to VLANs, see...
Page 267 Chapter Monitor the Switch Topic Page View Switch Status via Device Manager View Switch Status via the Logix Designer Application System Log Messages Trends Port Statistics NAT Statistics REP Topology CIP Status DLR Status Port Diagnostics Cable Diagnostics DHCP Pool Display Rockwell Automation Publication 1783-UM007B-EN-P - March 2015...
Page 268: Monitor The Switch
Chapter 8 Monitor the Switch View Switch Status via Use the Dashboard window to monitor switch status and performance. Device Manager Figure 30 shows the dashboard for a Stratix 5700 switch. Figure 30 - Dashboard Window The Dashboard window is similar to the Monitor > Trends window. The Dashboard window displays the instantaneous status while the Trends window displays the historical status.
Page 269: Stratix 5400, Stratix 5700, And Armorstratix 5700 Status Indicators
Monitor the Switch Chapter 8 Stratix 5400, Stratix 5700, and ArmorStratix 5700 Status Indicators The Front Panel view on the dashboard is a graphical display of the switch front panels. For Stratix 8000/8300 switches, the view also shows the attached...
Page 270 Chapter 8 Monitor the Switch Figure 33 - ArmorStratix 5700 Front Panel View Table 49 - Stratix 5400, Stratix 5700, and ArmorStratix 5700 Status Indicators Indicator Status Description EIP Mod The EIP Mod status indicator shows the status of the switch.
Page 271 Status —In this mode, the port status indicators show the status of the ports. Status mode is the default mode. IMPORTANT: Stratix 5400 switches have additional modes for the port status indicators. The meanings described below apply to only the Status mode. The default mode upon startup is the Status mode.
Page 272: Stratix 5400 Display Mode Switch
Chapter 8 Monitor the Switch Stratix 5400 Display Mode Switch The Stratix 5400 switch has a Display Mode switch (Figure 34) that lets you choose a mode for the port status indicators. The indicators to the left of the switch indicate the active display mode. Each time you press the switch, the active mode moves from the default Status mode to Speed, Duplex, PRP, and PoE respectively, and then back to Status mode.
Page 273: Stratix 8000 And 8300 Front Panel Status Indicators
Monitor the Switch Chapter 8 Stratix 8000 and 8300 Front Panel Status Indicators Figure 35 - Stratix 8000/8300 Front Panel View Table 51 - Stratix 8000/8300 Status Indicators Indicator Status Description EIP Mod The EIP Mod status indicator shows the status of the switch. Power to the switch is off or is not properly connected.
Page 274 Chapter 8 Monitor the Switch Table 52 - Stratix 8000/8300 Port-level Status Indicators Indicator Status Description Status In this mode, the port status indicators show the status of the ports. Status is the default mode. No link Solid green No activity on link. Flashing green Link activity.
Page 275: Switch Information
Monitor the Switch Chapter 8 Note the following: • The speed and Duplex mode for a port appear only when a device is connected to the port. • For dual-purpose ports, the Type field displays 10/100/1000BaseTX for the copper uplink port. The Type field also displays either the type of SFP module that is installed or Empty if a module is not installed.
Page 276: Switch Health
Chapter 8 Monitor the Switch Switch Health You can use the health gauges to monitor CPU utilization and temperature. The CPU Utilization gauge shows the percentage of CPU processing power that is in use on the switch. Data is collected at each 60-second system refresh. The gauge changes as the switch experiences the network activity from devices sending data through the network.
Page 277: Port Utilization
Monitor the Switch Chapter 8 Port Utilization You can choose which types of network traffic to display and in what format: • Types of traffic—By default, all traffic is displayed for all interfaces. Click the links above the display area to display all traffic, errors, received traffic, or transmitted traffic.
Page 278: View Switch Status Via The Logix Designer Application
Chapter 8 Monitor the Switch View Switch Status via the You can view status parameters for the switch. Logix Designer Application In the navigation pane, click Switch Status. Table 54 - Switch Status Fields Field Description Alarms & Faults Active Alarms Displays one of these values: •...
Page 279 Monitor the Switch Chapter 8 Table 54 - Switch Status Fields (continued) Field Description Image IOS Release Displays the current version of the switch operating system. License File Displays whether the license file is valid. SD Card Present Displays whether the SD card is installed. Power Power Present on Terminal A Displays a yes or no value to indicate whether power is present on Terminal A.
Page 280 Chapter 8 Monitor the Switch Table 55 - Module Info Fields Field Description Identification Displays the following switch information: • Vendor • Product type • Product code • Revision • Serial number • Product name Status Displays the following status information: •...
Page 281: Port Status
Monitor the Switch Chapter 8 Port Status In the navigation pane, click Port Status. You can monitor alarms, statuses, thresholds, and bandwidth utilization for each switch port. You can also access port and cable diagnostics. Table 56 - Port Status Fields Field Description Unit...
Page 282: System Log Messages
Chapter 8 Monitor the Switch Table 56 - Port Status Fields (continued) Field Description Threshold Exceeded Displays unusual changes for these types of network traffic: • Unicast—Displays a yes or no value to indicate whether the current unicast traffic has exceeded the threshold value. •...
Page 283 Monitor the Switch Chapter 8 To filter historical events, choose a severity filter or type filter: • Debugging—Debug messages. • Informational—Informational messages. • Notifications—The switch is operating normally but has a significant condition. • Warnings—The switch has a warning condition. •...
Page 284: Trends
Chapter 8 Monitor the Switch Trends In Device Manager, you can view historical data to help you to analyze traffic patterns and to identify problems. Data can be displayed in increments of seconds, minutes, hours, or days. To view the data in a table, click the Grid Mode button below the area. To display a chart, click the Chart Mode button.
Page 285: Port Statistics
Monitor the Switch Chapter 8 Port Statistics In Device Manager, you can view statistics for data that is sent and received by the switch ports. From the Monitor menu, choose Port Statistics. For more information, see the online help for Device Manager. The types of port statistics are grouped under these tabs on the Port Statistics window: •...
Page 286: Nat Statistics
Chapter 8 Monitor the Switch NAT Statistics You can monitor NAT statistics in both Device Manager and the Logix Designer application. Monitor NAT Statistics via Device Manager You can monitor these types of NAT statistics: • Global statistics for all instances •...
Page 287 Monitor the Switch Chapter 8 Table 59 - NAT Global Statistics Field Description Current Active Translations The number of IP addresses that have been translated within the last 90 seconds across all NAT instances. Total Translations The total number of translations across all NAT instances. Total NAT Translated Packets The total number of packets across all NAT instances.
Page 288: Monitor Nat Statistics Via The Logix Designer Application
Chapter 8 Monitor the Switch Monitor NAT Statistics via the Logix Designer Application For each NAT instance, you can monitor these diagnostics: • Diagnostics for both private and public translations • Diagnostics for only private translations • Diagnostics for only public translations In the navigation pane, click NAT, and then click the ellipse in the Diagnostics column.
Page 289 Monitor the Switch Chapter 8 Table 61 - NAT Diagnostics per Instance Field Description Current Active Translations Displays the number of translations that have occurred within the last 90 seconds across all NAT instances. Total NAT Translated Packets Displays the total number of packets that have been translated for this instance. Total Private to Public Address Translations Displays the total number of private-to-public translations for this instance.
Page 290: Private-To-Public Translation Diagnostics
Chapter 8 Monitor the Switch Private-to-Public Translation Diagnostics From the Private to Public Translations dialog box for an instance, you can view a list of IP addresses that have been changed by NAT within the last 90 seconds. Table 62 - Private-to-Public Translation Diagnostics Field Description Private...
Page 291: Public-To-Private Translation Diagnostics
Monitor the Switch Chapter 8 Public-to-Private Translation Diagnostics From the Public to Private Translations dialog box for an instance, you can view a list of IP addresses that have been changed by NAT within the last 90 seconds. Table 63 - Public-to-Private Translation Diagnostics Field Description Public...
Page 292: Rep Topology
Chapter 8 Monitor the Switch REP Topology In Device Manager, you can review the REP topology for one or all network segments. From the Monitor menu, choose REP. To display an archived REP topology, click the Archived Topology tab and then select the segment ID.
Page 293 Monitor the Switch Chapter 8 From the Monitor menu, choose CIP Status. Table 64 - CIP Status Fields Field Description Overview State The state of the CIP connection (Enabled or Disabled). Vlan The VLAN ID. CIP I/O Connection Owner The IP address of the device to and from which application-specific I/O output data is sent and received. CIP Config Session Owner The IP address of the device controlling the CIP configuration session.
Page 294: Dlr Status
Chapter 8 Monitor the Switch DLR Status You can monitor device-level ring (DLR) status in both Device Manager and the Logix Designer application. For more information about DLR troubleshooting, see Troubleshoot EtherNet/IP Networks, publication ENET-AT003. Monitor DLR Status via Device Manager From the Monitor menu, choose DLR: •...
Page 295: Monitor Dlr Status Via The Logix Designer Application
Monitor the Switch Chapter 8 Monitor DLR Status via the Logix Designer Application You can monitor DLR status on the Ring 1 and Members dialog boxes in the Logix Designer application. See Table 25 on page 171 Table 27 on page 173.
Page 296: Port Diagnostics
Chapter 8 Monitor the Switch Port Diagnostics The Port Diagnostics feature in the Logix Designer application lets you view the status of the link performance: • View octet and packet counters • View collisions on the link • View errors on the link You can also reset and clear all status counters.
Page 297 Monitor the Switch Chapter 8 Table 65 - Port Diagnostics Fields Field Description Unit Indicates where the port resides: • Base (for example, 1783-MS10T). (Stratix 8000/8300 • Expansion module (for example, 1783-MX08T). switches) Port The port that is selected for configuration. The port number includes the port type (Fa for Fast Ethernet and Gi for Gigabit Ethernet), the base or expansion module for Stratix 8000/8300 switches, and the specific port number.
Page 298: Cable Diagnostics
Chapter 8 Monitor the Switch Cable Diagnostics The Cable Diagnostics feature lets you run a test on each switch port to determine the integrity of the cable that is connected to the RJ45 (copper) ports. The test determines the distance to the break from the switch for each cable with a plus or minus error value individually listed.
Page 299: Diagnose Cables Via The Logix Designer Application
Monitor the Switch Chapter 8 Diagnose Cables via the Logix Designer Application In the navigation pane, click Port Status, and then click the button in the Cable Diagnostics column for the corresponding port. Table 66 - Cable Diagnostics Fields Field Description Port The port that is selected for configuration.
Page 300: Dhcp Pool Display
Chapter 8 Monitor the Switch DHCP Pool Display You can view DHCP address pool information for the switch. You can view 0…15 pools. This information is gathered directly from the switch. Each row represents one instance, and instance values cannot be consecutive. In the navigation pane, click DHCP Pool Display.
Page 301: Troubleshoot The Switch
Chapter Troubleshoot the Switch Topic Page Troubleshoot the Installation Verify Boot Fast Troubleshoot IP Address Issues Troubleshoot Device Manager Troubleshoot Switch Performance Access Direct Managed Mode Restart or Reset the Switch Recover the Switch Firmware Reset the Switch to Factory Defaults (Stratix 8000/8300 switches) Troubleshoot a Firmware Update This chapter helps you resolve issues that are related to Stratix switches and perform common functions, such as reset the switch.
Page 302: Troubleshoot The Installation
Chapter 9 Troubleshoot the Switch Troubleshoot the Installation The status indicators on the front panel provide troubleshooting information about the switch. They show power-on self-test (POST) failures, port connectivity problems, and overall switch performance. You can also get statistics from the browser interface, the command-line interface (CLI), or a Simple Network Management Protocol (SNMP) workstation.
Page 303: Bad Or Damaged Cable
Troubleshoot the Switch Chapter 9 Bad or Damaged Cable Always make sure that the cable does not have marginal damage or failure. Even if a cable is capable of connecting at the physical layer, subtle damage to the wiring or connectors can corrupt packets. This situation is likely when the port has many packet errors or the port constantly loses and regains the link.
Page 304: Link Status
Chapter 9 Troubleshoot the Switch Link Status Verify that both sides have a network link. A single broken wire or one shut down port can cause one side to show a link, but not the other side. A Link status indicator does not guarantee that the cable is fully functional.
Page 305: Verify Boot Fast
Troubleshoot the Switch Chapter 9 Verify Boot Fast Boot fast failures are potentially fatal to the switch. Contact your Rockwell Automation representative if your switch does not successfully complete boot fast. You can disable the boot fast and run a power-on self-test (POST) by using the CLI.
Page 306: Troubleshoot Switch Performance
Chapter 9 Troubleshoot the Switch Troubleshoot Switch The following table includes basic troubleshooting for issues that are related to switch performance. Performance Issue Resolution Speed, duplex, and autonegotiation Port statistics that show a large amount of alignment errors, frame check sequence (FCS), or late-collisions errors can indicate a speed or duplex mismatch.
Page 307 Troubleshoot the Switch Chapter 9 To access the Direct Managed mode, follow these steps. 1. Press the Express Setup button until the Setup status indicator blinks green and the status indicator of an available switch downlink port blinks green. The port with a flashing green status indicator is designated as the Direct Managed mode port: •...
Page 308: Restart Or Reset The Switch
Chapter 9 Troubleshoot the Switch Restart or Reset the Switch If you cannot solve an issue by reconfiguring a feature, you can restart or reset the switch to solve the issue. If the issue exists after you reset the switch to its default settings, it is unlikely that the switch is causing the issue.
Page 309: Restart The Switch From The Logix Designer Application
Troubleshoot the Switch Chapter 9 Restart the Switch from the Logix Designer Application All connections to or through the switch are closed when you reset a module. IMPORTANT Connection loss can result in loss of control. From Module Properties dialog box within the Logix Designer application, do the following.
Page 310: Recover The Switch Firmware
Chapter 9 Troubleshoot the Switch Recover the Switch Firmware Before you can recover switch firmware, make sure of the following: • You have physical access to the switch. • At least one switch port is enabled and is not connected to a device. You can recover the switch firmware if needed, such as in these scenarios: •...
Page 311: Data Types
Appendix Data Types Topic Page Stratix 5400 Data Types Stratix 5700 and ArmorStratix 5700 Data Types Stratix 8000 and 8300 Data Types In the Logix Designer application, predefined tags for Input and Output data types have a structure that corresponds to the switch selected when it was added to the I/O tree.
Page 312: Stratix 5400 Data Types
Appendix A Data Types Stratix 5400 Data Types The following tables list module-defined data types for Stratix 5400 switches. The tables include information for input (I) and output (O). 8-port Switches Catalog number 1783-HMS4C4CGN Table 69 - Input Data Types (8-port switches)
Page 313 Data Types Appendix A Table 69 - Input Data Types (8-port switches) (continued) AB:STRATIX_5400_8PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortGi1_3Utilization SINT Decimal PortGi1_4Utilization SINT Decimal PortFa1_5Utilization SINT Decimal PortFa1_6Utilization SINT Decimal PortFa1_7Utilization SINT Decimal PortFa1_8Utilization SINT Decimal MajorAlarmRelay BOOL Decimal...
Page 314: 12-Port Switches
Appendix A Data Types 12-port Switches Catalog numbers 1783-HMS8T4CGN,1783-HMS8S4CGN, 1783-HMS4T4E4CGN Table 71 - Input Data Types (12-port switches) AB:STRATIX_5400_12PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style Fault DINT Binary AnyPortConnected BOOL Decimal LinkStatus:0 PortGi1_1Connected BOOL Decimal LinkStatus:1 PortGi1_2Connected BOOL Decimal LinkStatus:2 PortGi1_3Connected...
Page 315 Data Types Appendix A Table 71 - Input Data Types (12-port switches) (continued) AB:STRATIX_5400_12PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortFa1_7Threshold BOOL Decimal ThresholdExceeded:7 PortFa1_8Threshold BOOL Decimal ThresholdExceeded:8 PortFa1_9Threshold BOOL Decimal ThresholdExceeded:9 PortFa1_10Threshold BOOL Decimal ThresholdExceeded:10 PortFa1_11Threshold BOOL Decimal ThresholdExceeded:11 PortFa1_12Threshold...
Page 316: 12-Port Gigabit Switches
Appendix A Data Types Table 72 - Output Data Type (12-port switches) (continued) AB:STRATIX_5400_12PORT_MANAGED:O:0 Member Name Type Default Display Style Valid Values PortFa1_10Disable BOOL Decimal DisablePort:10 PortFa1_11Disable BOOL Decimal DisablePort:11 PortFa1_12Disable BOOL Decimal DisablePort:12 12-port Gigabit Switches Catalog numbers 1783-HMS8TG4CGN, 1783-HMS8SG4CGN, 1783-HMS4EG8CGN, 1783-HMS8TG4CGR, 1783-HMS8SG4CGR, 1783-HMS4EG8CGR Table 73 - Input Data Types (12-port Gb switches)
Page 317 Data Types Appendix A Table 73 - Input Data Types (12-port Gb switches) (continued) AB:STRATIX_5400_12PORT_GB_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortGi1_11UnauthorizedDevice BOOL Decimal UnauthorizedDevice:11 PortGi1_12UnauthorizedDevice BOOL Decimal UnauthorizedDevice:12 AnyPortThreshold BOOL Decimal ThresholdExceeded:0 PortGi1_1Threshold BOOL Decimal ThresholdExceeded:1 PortGi1_2Threshold BOOL Decimal ThresholdExceeded:2...
Page 318: 16-Port Switches
Appendix A Data Types Table 74 - Output Data Type (12-port Gb switches) AB:STRATIX_5400_12PORT_GB_MANAGED:O:0 Member Name Type Default Display Style Valid Values AllPortsDisabled BOOL Decimal DisablePort:0 PortGi1_1Disable BOOL Decimal DisablePort:1 PortGi1_2Disable BOOL Decimal DisablePort:2 PortGi1_3Disable BOOL Decimal DisablePort:3 PortGi1_4Disable BOOL Decimal DisablePort:4 PortGi1_5Disable...
Page 319 Data Types Appendix A Table 75 - Input Data Type (16-port switches) (continued) AB:STRATIX_5400_16PORT_MANAGED:I:0 Member Name Type Default Display Style Valid Values PortFa1_16Connected BOOL Decimal LinkStatus:16 AnyPortUnauthorizedDevice BOOL Decimal UnauthorizedDevice:0 PortGi1_1UnauthorizedDevice BOOL Decimal UnauthorizedDevice:1 PortGi1_2UnauthorizedDevice BOOL Decimal UnauthorizedDevice:2 PortGi1_3UnauthorizedDevice BOOL Decimal UnauthorizedDevice:3 PortGi1_4UnauthorizedDevice...
Page 320 Appendix A Data Types Table 75 - Input Data Type (16-port switches) (continued) AB:STRATIX_5400_16PORT_MANAGED:I:0 Member Name Type Default Display Style Valid Values PortGi1_3Utilization SINT Decimal PortGi1_4Utilization SINT Decimal PortFa1_5Utilization SINT Decimal PortFa1_6Utilization SINT Decimal PortFa1_7Utilization SINT Decimal PortFa1_8Utilization SINT Decimal PortFa1_9Utilization SINT Decimal...
Page 321: 16-Port Gigabit Switches
Data Types Appendix A 16-port Gigabit Switches Catalog number 1783-HMS4SG8EG4CGN, 1783-HMS4SG8EG4CGR Table 77 - Input Data Type (16-port Gb switches) AB:STRATIX_5400_16PORT_GB_MANAGED:I:0 Member Name Type Default Display Style Valid Values Fault DINT Binary AnyPortConnected BOOL Decimal LinkStatus:0 PortGi1_1Connected BOOL Decimal LinkStatus:1 PortGi1_2Connected BOOL Decimal...
Page 322 Appendix A Data Types Table 77 - Input Data Type (16-port Gb switches) (continued) AB:STRATIX_5400_16PORT_GB_MANAGED:I:0 Member Name Type Default Display Style Valid Values AnyPortThreshold BOOL Decimal ThresholdExceeded:0 PortGi1_1Threshold BOOL Decimal ThresholdExceeded:1 PortGi1_2Threshold BOOL Decimal ThresholdExceeded:2 PortGi1_3Threshold BOOL Decimal ThresholdExceeded:3 PortGi1_4Threshold BOOL Decimal ThresholdExceeded:4...
Page 323: 20-Port Switches
Data Types Appendix A Table 78 - Output Data Type (16-port Gb switches) AB:STRATIX_5400_16PORT_GB_MANAGED:O:0 Member Name Type Default Display Style Valid Values AllPortsDisabled BOOL Decimal DisablePort:0 PortGi1_1Disable BOOL Decimal DisablePort:1 PortGi1_2Disable BOOL Decimal DisablePort:2 PortGi1_3Disable BOOL Decimal DisablePort:3 PortGi1_4Disable BOOL Decimal DisablePort:4 PortGi1_5Disable...
Page 324 Appendix A Data Types Table 79 - Input Data Type (20-port switches) (continued) AB:STRATIX_5400_20PORT_MANAGED:I:0 Member Name Type Default Display Style Valid Values PortFa1_12Connected BOOL Decimal LinkStatus:12 PortFa1_13Connected BOOL Decimal LinkStatus:13 PortFa1_14Connected BOOL Decimal LinkStatus:14 PortFa1_15Connected BOOL Decimal LinkStatus:15 PortFa1_16Connected BOOL Decimal LinkStatus:16 PortFa1_17Connected...
Page 325 Data Types Appendix A Table 79 - Input Data Type (20-port switches) (continued) AB:STRATIX_5400_20PORT_MANAGED:I:0 Member Name Type Default Display Style Valid Values PortFa1_8Threshold BOOL Decimal ThresholdExceeded:8 PortFa1_9Threshold BOOL Decimal ThresholdExceeded:9 PortFa1_10Threshold BOOL Decimal ThresholdExceeded:10 PortFa1_11Threshold BOOL Decimal ThresholdExceeded:11 PortFa1_12Threshold BOOL Decimal ThresholdExceeded:12 PortFa1_13Threshold...
Page 326: 20-Port Gigabit Switches
Appendix A Data Types Table 80 - Output Data Type (20-port switches) AB:STRATIX_5700_20PORT_MANAGED:O:0 Member Name Type Default Display Style Valid Values AllPortsDisabled BOOL Decimal DisablePort:0 PortGi1_1Disable BOOL Decimal DisablePort:1 PortGi1_2Disable BOOL Decimal DisablePort:2 PortGi1_3Disable BOOL Decimal DisablePort:3 PortGi1_4Disable BOOL Decimal DisablePort:4 PortFa1_5Disable BOOL...
Page 327 Data Types Appendix A Table 81 - Input Data Type (20-port Gb switches) (continued) AB:STRATIX_5400_20PORT_GB_MANAGED:I:0 Member Name Type Default Display Style Valid Values PortGi1_8Connected BOOL Decimal LinkStatus:8 PortGi1_9Connected BOOL Decimal LinkStatus:9 PortGi1_10Connected BOOL Decimal LinkStatus:10 PortGi1_11Connected BOOL Decimal LinkStatus:11 PortGi1_12Connected BOOL Decimal LinkStatus:12...
Page 328 Appendix A Data Types Table 81 - Input Data Type (20-port Gb switches) (continued) AB:STRATIX_5400_20PORT_GB_MANAGED:I:0 Member Name Type Default Display Style Valid Values PortGi1_4Threshold BOOL Decimal ThresholdExceeded:4 PortGi1_5Threshold BOOL Decimal ThresholdExceeded:5 PortGi1_6Threshold BOOL Decimal ThresholdExceeded:6 PortGi1_7Threshold BOOL Decimal ThresholdExceeded:7 PortGi1_8Threshold BOOL Decimal ThresholdExceeded:8...
Page 329 Data Types Appendix A Table 81 - Input Data Type (20-port Gb switches) (continued) AB:STRATIX_5400_20PORT_GB_MANAGED:I:0 Member Name Type Default Display Style Valid Values MajorAlarmRelay BOOL Decimal AlarmRelay:0 MinorAlarmRelay BOOL Decimal AlarmRelay:1 MulticastGroupActive DINT Binary Table 82 - Output Data Type (20-Gb port switches) AB:STRATIX_5700_20PORT_GB_MANAGED:O:0 Member Name Type...
Page 330: Stratix 5700 And Armorstratix 5700 Data Types
Appendix A Data Types Stratix 5700 and The following tables list module-defined data types for Stratix 5700 and ArmorStratix 5700 switches. The tables include information for input (I) and ArmorStratix 5700 output (O). Data Types 6-port Gb Switches Catalog numbers 1783-BMS4S2SGL, 1783-BMS4S2SGA,1783-BMS06SGL, 1783-BM06SGA, 1783-BMS06TGL, 1783-BMS06TGA Table 83 - Input Data Types (6-port Gb switches) AB:STRATIX_5700_6PORT_GB_MANAGED:I:O...
Page 331: 6-Port Switches
Data Types Appendix A Table 83 - Input Data Types (6-port Gb switches) (continued) AB:STRATIX_5700_6PORT_GB_MANAGED:I:O Member Name Type Default Display Valid Values Style PortGi1_2Utilization SINT Decimal MajorAlarmRelay BOOL Decimal AlarmRelay:0 MulticastGroupsActive DINT Binary Table 84 - Output Data Type (6-port Gb switches) AB:STRATIX_5700_6PORT_GB_MANAGED:O:0 Member Name Type...
Page 332 Appendix A Data Types Table 85 - Input Data Type (6-port switches) (continued) AB:STRATIX_5700_6PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortFa1_6UnauthorizedDevice BOOL Decimal UnauthorizedDevice:6 AnyPortThreshold BOOL Decimal ThresholdExceeded:0 PortFa1_1Threshold BOOL Decimal ThresholdExceeded:1 PortFa1_2Threshold BOOL Decimal ThresholdExceeded:2 PortFa1_3Threshold BOOL Decimal ThresholdExceeded:3 PortFa1_4Threshold...
Page 333: 8-Port Switches
Data Types Appendix A 8-port Switches Catalog number 1783-ZMS8TA Table 87 - Input Data Type (8-port switches) AB:STRATIX_5700_8PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style Fault DINT Binary AnyPortConnected BOOL Decimal LinkStatus:0 PortFa1_1Connected BOOL Decimal LinkStatus:1 PortFa1_2Connected BOOL Decimal LinkStatus:2 PortFa1_3Connected BOOL...
Page 334: 10-Port Gb Switches
Appendix A Data Types Table 87 - Input Data Type (8-port switches) (continued) AB:STRATIX_5700_8PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortFa1_7Utilization SINT Decimal PortFa1_8Utilization SINT Decimal MajorAlarmRelay BOOL Decimal AlarmRelay:0 MulticastGroupsActive DINT Binary Table 88 - Output Data Type (8-port switches) AB:STRATIX_5700_8PORT_MANAGED:O:0 Member Name Type...
Page 335 Data Types Appendix A Table 89 - Input Data Type (10-port Gb switches) (continued) AB:STRATIX_5700_10PORT_GB_MANAGED:I:0 Member Name Type Default Display Style Valid Values PortGi1_2Connected BOOL Decimal LinkStatus:10 AnyPortUnauthorizedDevice BOOL Decimal UnauthorizedDevice:0 PortFa1_1UnauthorizedDevice BOOL Decimal UnauthorizedDevice:1 PortFa1_2UnauthorizedDevice BOOL Decimal UnauthorizedDevice:2 PortFa1_3UnauthorizedDevice BOOL Decimal UnauthorizedDevice:3...
Page 336: 10-Port Switches
Appendix A Data Types Table 90 - Output Data Type (10-port Gb switches) AB:STRATIX_5700_10PORT_MANAGED:O:0 Member Name Type Default Display Style Valid Values AllPortsDisabled BOOL Decimal DisablePort:0 PortFa1_1Disable BOOL Decimal DisablePort:1 PortFa1_2Disable BOOL Decimal DisablePort:2 PortFa1_3Disable BOOL Decimal DisablePort:3 PortFa1_4Disable BOOL Decimal DisablePort:4 PortFa1_5Disable...
Page 337 Data Types Appendix A Table 91 - Input Data Type (10-port switches) (continued) AB:STRATIX_5700_10PORT_MANAGED:I:0 Member Name Type Default Display Style Valid Values PortFa1_7UnauthorizedDevice BOOL Decimal UnauthorizedDevice:7 PortFa1_8UnauthorizedDevice BOOL Decimal UnauthorizedDevice:8 PortFa1_9UnauthorizedDevice BOOL Decimal UnauthorizedDevice:9 PortFa1_10UnauthorizedDevice BOOL Decimal UnauthorizedDevice:10 AnyPortThreshold BOOL Decimal ThresholdExceeded:0 PortFa1_1Threshold...
Page 338: 16-Port Switches
Appendix A Data Types Table 92 - Output Data Type (10-port switches) AB:STRATIX_5700_10PORT_MANAGED:O:0 Member Name Type Default Display Style Valid Values AllPortsDisabled BOOL Decimal DisablePort:0 PortFa1_1Disable BOOL Decimal DisablePort:1 PortFa1_2Disable BOOL Decimal DisablePort:2 PortFa1_3Disable BOOL Decimal DisablePort:3 PortFa1_4Disable BOOL Decimal DisablePort:4 PortFa1_5Disable BOOL...
Page 339 Data Types Appendix A Table 93 - Input Data Type (16-port switches) (continued) AB:STRATIX_5700_16PORT_MANAGED:I:0 Member Name Type Default Display Style Valid Values PortFa1_1UnauthorizedDevice BOOL Decimal UnauthorizedDevice:1 PortFa1_2UnauthorizedDevice BOOL Decimal UnauthorizedDevice:2 PortFa1_3UnauthorizedDevice BOOL Decimal UnauthorizedDevice:3 PortFa1_4UnauthorizedDevice BOOL Decimal UnauthorizedDevice:4 PortFa1_5UnauthorizedDevice BOOL Decimal UnauthorizedDevice:5 PortFa1_6UnauthorizedDevice...
Page 340 Appendix A Data Types Table 93 - Input Data Type (16-port switches) (continued) AB:STRATIX_5700_16PORT_MANAGED:I:0 Member Name Type Default Display Style Valid Values PortFa1_5Utilization SINT Decimal PortFa1_6Utilization SINT Decimal PortFa1_7Utilization SINT Decimal PortFa1_8Utilization SINT Decimal PortFa1_9Utilization SINT Decimal PortFa1_10Utilization SINT Decimal PortFa1_11Utilization SINT Decimal...
Page 341: 20-Port Gb Switches
Data Types Appendix A 20-port Gb Switches Catalog numbers 1783-BMS20CGL, 1783-BMS20CGN, 1783-BMS20CGP, 1783-BMS20CGPK Table 95 - Input Data Type (20-port Gb switches) AB:STRATIX_5700_20PORT_GB_MANAGED:I:0 Member Name Type Default Display Valid Values Style Fault DINT Binary AnyPortConnected BOOL Decimal LinkStatus:0 PortFa1_1Connected BOOL Decimal LinkStatus:1 PortFa1_2Connected...
Page 342 Appendix A Data Types Table 95 - Input Data Type (20-port Gb switches) (continued) AB:STRATIX_5700_20PORT_GB_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortFa1_12UnauthorizedDevice BOOL Decimal UnauthorizedDevice:12 PortFa1_13UnauthorizedDevice BOOL Decimal UnauthorizedDevice:13 PortFa1_14UnauthorizedDevice BOOL Decimal UnauthorizedDevice:14 PortFa1_15UnauthorizedDevice BOOL Decimal UnauthorizedDevice:15 PortFa1_16UnauthorizedDevice BOOL Decimal UnauthorizedDevice:16...
Page 343: 18-Port Gb Switches
Data Types Appendix A Table 95 - Input Data Type (20-port Gb switches) (continued) AB:STRATIX_5700_20PORT_GB_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortFa1_8Utilization SINT Decimal PortFa1_9Utilization SINT Decimal PortFa1_10Utilization SINT Decimal PortFa1_11Utilization SINT Decimal PortFa1_12Utilization SINT Decimal PortFa1_13Utilization SINT Decimal PortFa1_14Utilization SINT...
Page 344 Appendix A Data Types Table 96 - Input Data Type (18-port Gb switches) (continued) AB:STRATIX_5700_18PORT_GB_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortFa1_12Connected BOOL Decimal LinkStatus:12 PortFa1_13Connected BOOL Decimal LinkStatus:13 PortFa1_14Connected BOOL Decimal LinkStatus:14 PortFa1_15Connected BOOL Decimal LinkStatus:15 PortFa1_16Connected BOOL Decimal LinkStatus:16...
Page 345 Data Types Appendix A Table 96 - Input Data Type (18-port Gb switches) (continued) AB:STRATIX_5700_18PORT_GB_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortFa1_12Threshold BOOL Decimal ThresholdExceeded:12 PortFa1_13Threshold BOOL Decimal ThresholdExceeded:13 PortFa1_14Threshold BOOL Decimal ThresholdExceeded:14 PortFa1_15Threshold BOOL Decimal ThresholdExceeded:15 PortFa1_16Threshold BOOL Decimal ThresholdExceeded:16...
Page 346 Appendix A Data Types Table 97 - Output Data Type (18-port Gb switches) AB:STRATIX_5700_20PORT_GB_MANAGED:O:0 Member Name Type Default Display Valid Values Style AllPortsDisabled BOOL Decimal DisablePort:0 PortFa1_1Disable BOOL Decimal DisablePort:1 PortFa1_2Disable BOOL Decimal DisablePort:2 PortFa1_3Disable BOOL Decimal DisablePort:3 PortFa1_4Disable BOOL Decimal DisablePort:4 PortFa1_5Disable...
Page 347: 20-Port Gb Switches
Data Types Appendix A 20-port Gb Switches Catalog numbers 1783-BMS20CGL, 1783-BMS20CGN, 1783-BMS20CGP, 1783-BMS20CGPK Table 98 - Input Data Type (20-port Gb switches) AB:STRATIX_5700_20PORT_GB_MANAGED:I:0 Member Name Type Default Display Valid Values Style Fault DINT Binary AnyPortConnected BOOL Decimal LinkStatus:0 PortFa1_1Connected BOOL Decimal LinkStatus:1 PortFa1_2Connected...
Page 348 Appendix A Data Types Table 98 - Input Data Type (20-port Gb switches) (continued) AB:STRATIX_5700_20PORT_GB_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortFa1_12UnauthorizedDevice BOOL Decimal UnauthorizedDevice:12 PortFa1_13UnauthorizedDevice BOOL Decimal UnauthorizedDevice:13 PortFa1_14UnauthorizedDevice BOOL Decimal UnauthorizedDevice:14 PortFa1_15UnauthorizedDevice BOOL Decimal UnauthorizedDevice:15 PortFa1_16UnauthorizedDevice BOOL Decimal UnauthorizedDevice:16...
Page 349 Data Types Appendix A Table 98 - Input Data Type (20-port Gb switches) (continued) AB:STRATIX_5700_20PORT_GB_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortFa1_8Utilization SINT Decimal PortFa1_9Utilization SINT Decimal PortFa1_10Utilization SINT Decimal PortFa1_11Utilization SINT Decimal PortFa1_12Utilization SINT Decimal PortFa1_13Utilization SINT Decimal PortFa1_14Utilization SINT...
Page 350: 20-Port Switches
Appendix A Data Types Table 99 - Output Data Type (20-port Gb switches) (continued) AB:STRATIX_5700_20PORT_GB_MANAGED:O:0 Member Name Type Default Display Valid Values Style PortFa1_18Disable BOOL Decimal DisablePort:18 PortGi1_1Disable BOOL Decimal DisablePort:19 PortGi1_2Disable BOOL Decimal DisablePort:20 20-port Switches Catalog numbers 1783-BMS20CL, 1783-BMS20CA Table 100 - Input Data Type (20-port switches) AB:STRATIX_5700_20PORT_MANAGED:I:0 Member Name...
Page 351 Data Types Appendix A Table 100 - Input Data Type (20-port switches) (continued) AB:STRATIX_5700_20PORT_MANAGED:I:0 Member Name Type Default Display Style Valid Values PortFa1_5UnauthorizedDevice BOOL Decimal UnauthorizedDevice:5 PortFa1_6UnauthorizedDevice BOOL Decimal UnauthorizedDevice:6 PortFa1_7UnauthorizedDevice BOOL Decimal UnauthorizedDevice:7 PortFa1_8UnauthorizedDevice BOOL Decimal UnauthorizedDevice:8 PortFa1_9UnauthorizedDevice BOOL Decimal UnauthorizedDevice:9 PortFa1_10UnauthorizedDevice...
Page 352 Appendix A Data Types Table 100 - Input Data Type (20-port switches) (continued) AB:STRATIX_5700_20PORT_MANAGED:I:0 Member Name Type Default Display Style Valid Values PortFa1_1Utilization SINT Decimal PortFa1_2Utilization SINT Decimal PortFa1_3Utilization SINT Decimal PortFa1_4Utilization SINT Decimal PortFa1_5Utilization SINT Decimal PortFa1_6Utilization SINT Decimal PortFa1_7Utilization SINT Decimal...
Page 353: 24-Port Switches
Data Types Appendix A Table 101 - Output Data Type (20-port switches) (continued) AB:STRATIX_5700_20PORT_MANAGED:O:0 Member Name Type Default Display Style Valid Values PortFa1_12Disable BOOL Decimal DisablePort:12 PortFa1_13Disable BOOL Decimal DisablePort:13 PortFa1_14Disable BOOL Decimal DisablePort:14 PortFa1_15Disable BOOL Decimal DisablePort:15 PortFa1_16Disable BOOL Decimal DisablePort:16 PortFa1_17Disable...
Page 354 Appendix A Data Types Table 102 - Input Data Type (24-port switches) (continued) AB:STRATIX_5700_24PORT_MANAGED:I:0 Member Name Type Default Display Style Valid Values PortFa1_21Connected BOOL Decimal LinkStatus:21 PortFa1_22Connected BOOL Decimal LinkStatus:22 PortFa1_23Connected BOOL Decimal LinkStatus:23 PortFa1_24Connected BOOL Decimal LinkStatus:24 AnyPortUnauthorizedDevice BOOL Decimal UnauthorizedDevice:0 PortFa1_1UnauthorizedDevice...
Page 355 Data Types Appendix A Table 102 - Input Data Type (24-port switches) (continued) AB:STRATIX_5700_24PORT_MANAGED:I:0 Member Name Type Default Display Style Valid Values PortFa1_9Threshold BOOL Decimal ThresholdExceeded:9 PortFa1_10Threshold BOOL Decimal ThresholdExceeded:10 PortFa1_11Threshold BOOL Decimal ThresholdExceeded:11 PortFa1_12Threshold BOOL Decimal ThresholdExceeded:12 PortFa1_13Threshold BOOL Decimal ThresholdExceeded:13 PortFa1_14Threshold...
Page 356 Appendix A Data Types Table 102 - Input Data Type (24-port switches) (continued) AB:STRATIX_5700_24PORT_MANAGED:I:0 Member Name Type Default Display Style Valid Values PortFa1_22Utilization SINT Decimal PortFa1_23Utilization SINT Decimal PortFa1_24Utilization SINT Decimal MajorAlarmRelay BOOL Decimal AlarmRelay:0 MulticastGroupsActive DINT Binary Table 103 - Output Data Type (24-port switches) AB:STRATIX_5700_24PORT_MANAGED:O:0 Member Name Type...
Page 357: Stratix 8000 And 8300 Data Types
Data Types Appendix A Stratix 8000 and 8300 The following tables show input and output data types for all 26 ports of the switch, as well as port assignments for data types. Data Types Table 104 - Input Data Types Tag Name Type Description...
Page 358: Rockwell Automation Publication 1783-Um007B-En-P - March
Appendix A Data Types Table 104 - Input Data Types (continued) Tag Name Type Description PortGi1_1UnauthorizedDevice BOOL Indicates that an unauthorized MAC ID has attempted to communicate on a particular port. PortGi1_2UnauthorizedDevice BOOL 0 = No mismatch 1 = Mismatch PortFa1_1UnauthorizedDevice BOOL PortFa1_2UnauthorizedDevice...
Page 359 Data Types Appendix A Table 104 - Input Data Types (continued) Tag Name Type Description PortGi1_1Threshold BOOL Indicates that unicast, multicast, or broadcast threshold limit has been exceeded on a particular port. PortGi1_2Threshold BOOL 0 = OK 1 = Threshold exceeded PortFa1_1Threshold BOOL PortFa1_2Threshold...
Page 360 Appendix A Data Types Table 104 - Input Data Types (continued) Tag Name Type Description PortFa1_2Utilization; SINT The percentage of the bandwidth utilized on a particular port. PortFa1_3Utilization; SINT PortFa1_4Utilization; SINT PortFa1_5Utilization; SINT PortFa1_6Utilization; SINT PortFa1_7Utilization; SINT PortFa1_8Utilization; SINT PortFa2_1Utilization; SINT PortFa2_2Utilization;...
Page 361 Data Types Appendix A Table 105 - Output Data Types Tag Name Type Description AllPortsDisable BOOL Setting this bit disables all ports on the switch. 0 = Enable 1 = Disable PortGi1_1Disable BOOL Setting a particular bit disables that particular port. 0 = Enable PortGi1_2Disable BOOL...
Page 362 Appendix A Data Types Notes: Rockwell Automation Publication 1783-UM007B-EN-P - March 2015...
Page 363 Appendix Port Assignments for CIP Data Topic Page Stratix 5400 Port Assignments Stratix 5700 Port Assignments ArmorStratix 5700 Port Assignments Stratix 8000 and 8300 Port Assignments The following tables identify the instance numbers of the Ethernet link objects that are associated with each port on the switch. Instance 0 does not apply to all ports as it does for bit maps.
Page 364: Stratix 5400 Port Assignments
Appendix B Port Assignments for CIP Data Stratix 5400 Port Assignments Table 106 - 8- and 12-port Switches Instance/ 1783-HMS4C4CGN 1783-HMS8T4CGN 1783-HMS8S4CGN 1783-HMS4T4E4CGN 1783-HMS8TG4CGN 1783-HMS8SG4CGN 1783-HMS4EG8CGN 1783-HMS8TG4CGR 1783-HMS8SG4CGR 1783-HMS4EG8CGR 0 Any/All ports Any/All ports Any/All ports Any/All ports Any/All ports...
Page 365 Port Assignments for CIP Data Appendix B Table 107 - 16- and 20-port Switches Instance/ 1783-HMS4S8E4CGN 1783-HMS4SG8EG4CGN 1783-HMS16T4CGN 1783-HMS16TG4CGN 1783-HMS8TG8EG4CGN 1783-HMS4SG8EG4CGR 1783-HMS16TG4CGR 1783-HMS8TG8EG4CGR 0 Any/All ports Any/All ports Any/All ports Any/All ports Any/All ports 1 Gi1/1 Gi1/1 Gi1/1 Gi1/1 Gi1/1 2 Gi1/2 Gi1/2 Gi1/2...
Page 366: Stratix 5700 Port Assignments
Appendix B Port Assignments for CIP Data Stratix 5700 Port Assignments Table 108 - 6- and 10-port Switches Instance/ 1783-BMS4S2SGL, 1783-BMS4S2SGA, 1783-BMS06TGL, 1783-BMS10CL, 1783-BMS10CGL, 1783-BMS10CGA, 1783-BMS06SL, 1783-BMS06SA, 1783-BMS10CGP, 1783-BMS10CGN 1783-BMS06TGA 1783-BMS10CA 1783-BMS06TL, 1783-BMS06TA, 1783-BMS06SGL, 1783-BMS06SGA 0 Any/All ports Any/All ports Any/All ports Any/All ports 1 Fa1/1...
Page 367: Armorstratix 5700 Port Assignments
Port Assignments for CIP Data Appendix B Table 109 - 18- and 20-port Switches (continued) Instance/ 1783-BMS12T4E2CGL, 1783-BMS12T4E2CGP, 1783-BMS20CL, 1783-BMS20CA 1783-BMS20CGL, 1783-BMS20CGN, 1783-BMS12T4E2CGNK 1783-BMS20CGP, 1783-BMS20CGPK Fa1/19 Gi1/1 Fa1/20 Gi1/2 27 SVI1 SVI1 SVI1 ArmorStratix 5700 Port Assignments Instance/ 1783-ZMS8TA 1783-ZMS4T4E2TGP, 1783-ZMS16TA 1783-ZMS8T8E2TGP, 1783-ZMS24TA...
Page 368: Stratix 8000 And 8300 Port Assignments
Appendix B Port Assignments for CIP Data Stratix 8000 and 8300 Port Assignments Instance/Bit 6-port Managed 10-port Managed 10-port Managed 14-port Managed 14-port Managed 14-port Managed 18-port Managed Ethernet Switch Ethernet Switch Ethernet Switch Ethernet Switch Ethernet Switch Ethernet Switch Ethernet Switch Bit 0 Any/All ports Any/All ports...
Page 369 Appendix Port Numbering Topic Page Stratix 5400 Port Numbering Stratix 5700 Port Numbering ArmorStratix 5700 Port Numbering Stratix 8000 and 8300 Port Numbering Rockwell Automation Publication 1783-UM007B-EN-P - March 2015...
Page 370: Stratix 5400 Port Numbering
• Unit number (always 1) • Port number (1…20, depending on the catalog number) Gigabit Ethernet is abbreviated as Gi and Fast Ethernet as Fa. Table 110 - Stratix 5400 Port Numbering Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.txt Text File...
Page 371 Port Numbering Appendix C Table 110 - Stratix 5400 Port Numbering (continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.txt Text File 1783-HMS4T4E4CGN 12-port (4 combo Gigabit ports; 4 Ethernet ports; 4 PoE/ Gi1/1 PoE+ ports) managed switch; Layer 2 firmware...
Page 372 Appendix C Port Numbering Table 110 - Stratix 5400 Port Numbering (continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.txt Text File 1783-HMS8S8E4CGN 16-port (4 combo Gigabit ports; 8 PoE/PoE+ ports; 4 SFP Gi1/1 ports) managed switch; Layer 2 firmware...
Page 373 Port Numbering Appendix C Table 110 - Stratix 5400 Port Numbering (continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.txt Text File 1783-HMS16T4CGN 20-port (4 combo Gigabit ports; 16 Ethernet ports) managed Gi1/1 switch; Layer 2 firmware...
Page 374 Appendix C Port Numbering Table 110 - Stratix 5400 Port Numbering (continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.txt Text File 1783-HMS8TG8EG4CGN 20-port (8 Gigabit ports; 4 Gigabit combo ports; 8 Gigabit Gi1/1 PoE/PoE+ ports) managed switch; Layer 2 firmware...
Page 375 Port Numbering Appendix C Table 110 - Stratix 5400 Port Numbering (continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.txt Text File 1783-HMS4EG8CGR 12-port (4 Gigabit ports; 4 Gigabit combo ports; 4 Gigabit Gi1/1 PoE/PoE+ ports) managed switch; Layer 3 firmware...
Page 376 Appendix C Port Numbering Table 110 - Stratix 5400 Port Numbering (continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.txt Text File 1783-HMS4SG8EG4CGR 16-port (4 Gigabit combo ports; 8 Gigabit PoE/PoE+ ports; Gi1/1 4 Gigabit SFP ports) managed switch; Layer 3 firmware...
Page 377 Port Numbering Appendix C Table 110 - Stratix 5400 Port Numbering (continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.txt Text File 1783-HMS8TG8EG4CGR 20-port (8 Gigabit ports; 4 Gigabit combo ports; 8 Gigabit Gi1/1 PoE/PoE+ ports) managed switch; Layer 3 firmware...
Page 378: Stratix 5700 Port Numbering
Appendix C Port Numbering Stratix 5700 Port Numbering The port ID consists of the following: • Port type (Gigabit Ethernet for Gigabit ports and Fast Ethernet for 10/100 Mbps ports) • Unit number (always 1) • Port number (1…2 for Gigabit ports, 1…18 for all others, depending on the catalog number) Gigabit Ethernet is abbreviated as Gi and Fast Ethernet as Fa.
Page 379 Port Numbering Appendix C Table 111 - Stratix 5700 Port Numbering (continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.text File 1783-BM06SGA 6-port (4 Ethernet ports; 2 SFP Gigabit slots) managed switch; full Fa1/1 firmware Fa1/2 Fa1/3 Fa1/4 Gi1/1...
Page 380 Appendix C Port Numbering Table 111 - Stratix 5700 Port Numbering (continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.text File 1783-BMS10CGA 10-port (8 Ethernet ports; 2 combo Gigabit ports) managed switch; full Fa1/1 firmware Fa1/2 Fa1/3 Fa1/4 Fa1/5...
Page 381 Port Numbering Appendix C Table 111 - Stratix 5700 Port Numbering (continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.text File 1783-BMS12T4E2CGP 18-port (12 Ethernet ports; 4 PoE/PoE+ ports; 2 combo Gigabit ports) Fa1/1 managed switch; full firmware; PTP Fa1/2 Fa1/3 Fa1/4...
Page 382 Appendix C Port Numbering Table 111 - Stratix 5700 Port Numbering (continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.text File 1783-BMS20CA 20-port (16 Ethernet ports; 2 SFP slots; 2 combo ports) managed switch; Fa1/1 full firmware Fa1/2 Fa1/3 Fa1/4...
Page 383 Port Numbering Appendix C Table 111 - Stratix 5700 Port Numbering (continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.text File 1783-BMS20CGN 20-port (16 Ethernet ports; 2 SFP slots; 2 combo Gigabit ports) Fa1/1 managed switch; full firmware; PTP; NAT Fa1/2 Fa1/3 Fa1/4...
Page 384 Appendix C Port Numbering Table 111 - Stratix 5700 Port Numbering (continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.text File 1783-BMS20CGPK 20-port (16 Ethernet ports; 2 SFP slots; 2 combo Gigabit ports) Fa1/1 managed switch; full firmware; PTP; conformal coating Fa1/2 Fa1/3 Fa1/4...
Page 385: Armorstratix 5700 Port Numbering
Port Numbering Appendix C ArmorStratix 5700 The port ID consists of the following: • Port type (Gigabit Ethernet for Gigabit ports and Fast Ethernet for Port Numbering 10/100 Mbps ports) • Unit number (always 1) • Port number (1…2 for Gigabit ports, 1…18 for all others, depending on the catalog number) Gigabit Ethernet is abbreviated as Gi and Fast Ethernet as Fa.
Page 386 Appendix C Port Numbering Table 112 - ArmorStratix 5700 Port Numbering (continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.text File 1783-ZMS8T8E2TGP 18-port (2 Gigabit ports; 8 Ethernet ports; 8 PoE/PoE+ ports) GE-1 Gi1/1 managed switch; full firmware; PTP GE-2 Gi1/2 Fa1/1...
Page 387 Port Numbering Appendix C Table 112 - ArmorStratix 5700 Port Numbering (continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.text File 1783-ZMS24TA 24-port (24 Ethernet ports) managed switch; full firmware Fa1/1 Fa1/2 Fa1/3 Fa1/4 Fa1/5 Fa1/6 Fa1/7 Fa1/8 Fa1/9...
Page 388: Stratix 8000 And 8300 Port Numbering
Appendix C Port Numbering Stratix 8000 and 8300 The port ID consists of the following: • Port type (Gigabit Ethernet for Gigabit ports and Fast Ethernet for Port Numbering 10/100 Mbps ports) • Unit number (1, 2, or 3) • Port number (1…2 for Gigabits, 1…4 for the 6-port base and 1…8 for all others) Gigabit Ethernet is abbreviated as Gi and Fast Ethernet as Fa.
Page 389 Port Numbering Appendix C Table 113 - Stratix 8000/8300 Switch and Expansion Module Port Numbering (continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.txt Text File 1783-MX04E 4-port (4 PoE ports) expansion module Fa#/1 Fa#/2 Fa#/3 Fa#/4 1783-MX04T04E 8-port(4 Ethernet ports;...
Page 390 Appendix C Port Numbering Notes: Rockwell Automation Publication 1783-UM007B-EN-P - March 2015...
Page 391: Stratix 5700 And 5400 Cables And Connectors
Technical Data, publication 1783-TD001. Stratix 5700 and 5400 This section provides details about connecting to ports on Stratix 5700 and Stratix 5400 switches. Cables and Connectors 10/100 and 10/100/1000 Ports The 10/100 and 10/100/1000 Ethernet ports on switches use standard RJ45 connectors and Ethernet pinouts with internal crossovers.
Page 392: Connect To 10Base-T- And 100Base-Tx-Compatible Devices
Appendix D Cables and Connectors Figure 37 - 10/100/1000 Connector Pinouts Label 4 5 6 7 8 TP0+ TP0- TP1+ TP2+ TP2- TP1- TP3+ TP3- PoE ports integrate power and data signals on the same wires. The ports use standard RJ45 connectors and Ethernet pinouts with internal crossovers. Figure 38 - 10/100 PoE Connector Pinouts and Power Sourcing Equipment (PSE) Voltage Label Alternative A (MDI)
Page 393 Cables and Connectors Appendix D Figure 39 Figure 40 show the cable schematics. Figure 39 - Two Twisted-pair Straight-through Cable Schematic Switch Router or Personal Computer 3 TD+ 3 RD+ 6 TD– 6 RD– 1 RD+ 1 TD+ 2 TD– 2 RD–...
Page 394: Dual-Purpose Ports (Combo Ports)
Appendix D Cables and Connectors Figure 41 Figure 42 show the cable schematics. Figure 41 - Two Twisted-pair Crossover Cable Schematic Switch Switch 3 TD+ 3 TD+ 6 TD– 6 TD– 1 RD+ 1 RD+ 2 RD– 2 RD– Figure 42 - Four Twisted-pair Crossover Cable Schematic Switch Switch 1 TPO+...
Page 395: Console Ports
Cables and Connectors Appendix D Console Ports Console ports enable you to connect a switch to a computer if you use the Command-line interface (CLI) to configure and monitor a switch. Stratix 5700 switches have these console ports: • A USB 5-pin mini-Type B port on the front panel The USB console port uses a USB Type A to 5-pin mini-Type B cable.
Page 396 Appendix D Cables and Connectors The following table lists the pinouts for the console port, the RJ45-to-DB-9 adapter cable, and the console device. Table 114 - Pinouts with DB-9 Pin Switch Console Port (DTE) RJ45-to-DB-9 Terminal Adapter Console Device Signal DB-9 Pin Signal The following table lists the pinouts for the console port, RJ45-to-DB-25 female...
Page 397: Alarm Ports
Cables and Connectors Appendix D Alarm Ports The front-panel alarm-relay connector ports are described in the following illustration and table. Figure 44 - Wiring Example for Alarm Inputs and Outputs Alarms Connector To Alarm Input Alarm +24V DC from User Relay Coil To Alarm Input...
Page 398: Sfp Module Specifications
Appendix D Cables and Connectors SFP Module Specifications The following lists the SFP module specifications for the rugged fiber-optic SFP module connections. Each port must match the wave-length specifications on the other end of the cable, and for reliable communication, the cable must not exceed the rated maximum cable length.
Page 399: Armorstratix 5700 Cables And Connectors
Cables and Connectors Appendix D ArmorStratix 5700 This section provides details about connecting to ports on ArmorStratix 5700 switches. For connecting DC power to the power connector, see page Cables and Connectors 10/100 Ports The 10/100 Ethernet ports use M12 D-coded 4-pin connectors and Ethernet pinouts with twisted-pair crossovers or straight-through cables.
Page 400: Connect To 10Base-T- And 100Base-Tx-Compatible Devices
Appendix D Cables and Connectors Connect to 10BASE-T- and 100BASE-TX-Compatible Devices The auto-MDIX feature is enabled by default. Follow these cabling guidelines when the auto-MDIX feature has been disabled. When connecting the ports to 10BASE-T- and 100BASE-TX-compatible devices, such as servers, workstations, and routers, you can use a two or four twisted-pair, straight-through cable that is wired for 10BASE-T and 100BASE-TX.
Page 401 Cables and Connectors Appendix D When connecting the ports to 10BASE-T- and 100BASE-TX-compatible devices, such as switches or repeaters, you can use a two or four twisted-pair, crossover cable. Use a straight-through cable to connect two ports when only one port is designated with an X.
Page 402: Console Port
(Figure 51): • Obtain a male 5-pin DC Micro-style (M12) connector configuration cordset, such as Allen-Bradley Bulletin 889D. See publication 889DS-PP001. • Obtain a DB-9 connector and attach it to one end of the cable. Figure 51 - M12-to-DB-9 Cable...
Page 403: Alarm Ports
Alarm ports are included only on ArmorStratix 5700 switches with PoE. The front-panel alarm relay connector and ports are described below. The alarm connector uses a male 5-pin DC Micro-style (M12) connector configuration cordset, such as Allen-Bradley Bulletin 889D. See publication 889DS-PP001. Figure 54 - Alarm Connector Pinout Unconnected...
Page 404: Poe Port Cable Specifications
Appendix D Cables and Connectors PoE Port Cable Specifications For PoE ports, use a Category 5 (Cat 5) cable with a distance of up to 100 m (328 ft). Stratix 8000/8300 This section provides details about connecting to ports on Stratix 8000/8300 switches.
Page 405: Connect To 10Base-T- And 100Base-Tx-Compatible Devices
Cables and Connectors Appendix D The PoE ports on the PoE expansion modules integrate power and data signals on the same wires. The ports use standard RJ45 connectors and Ethernet pinouts with internal crossovers. Figure 58 - 10/100 PoE Connector Pinouts and Power Sourcing Equipment (PSE) Voltage Label Alternative A (MDI) 4 5 6 7 8...
Page 406 Appendix D Cables and Connectors When connecting the ports to 10BASE-T- and 100BASE-TX-compatible devices, such as switches or repeaters, you can use a two or four twisted-pair, crossover cable. Use a straight-through cable to connect two ports only when one port is designated with an X.
Page 407: 100Base-Fx Ports
Cables and Connectors Appendix D 100BASE-FX Ports The 100BASE-FX ports use the following: • LC connectors, as shown in the following figure • 50/125- or 62.5/125-micron multimode fiber-optic cables Figure 63 - Fiber-optic SFP Module LC Connector ATTENTION: Invisible laser radiation can be emitted from disconnected fibers or connectors.
Page 408: Console Port
Appendix D Cables and Connectors Console Port The console port enables you to connect the switch to a computer if you use the Command-line interface (CLI) to configure and monitor the switch. The console port uses an 8-pin RJ45 connector. The supplied RJ45-to-DB-9 adapter cable connects the console port of the switch to a computer.
Page 409: Sfp Module Specifications
Cables and Connectors Appendix D The following table lists the pinouts for the console port, RJ45-to-DB-25 female DTE adapter, and the console device. The RJ45-to-DB-25 female DTE adapter is not supplied with the switch. Table 118 - Pinouts with DB-25 Pin Switch Console Port (DTE) RJ45-to-DB-25 Terminal Adapter Console Device...
Page 410 Appendix D Cables and Connectors Notes: Rockwell Automation Publication 1783-UM007B-EN-P - March 2015...
Page 411 Index Numerics using 393 damaged 303 10/100 ports detect with auto-MDIX 32 cable lengths 30 Ethernet and fiber 303 connecting to 47 identify 405 10/100/1000 ports optical 398 PoE module specifications 409 cable lengths 30 SFP module 398 connecting to 47 SFP module specifications 409 straight-through two twisted-pair pinout 393...
Page 412 Index default gateway NAT 185 Half-duplex mode 131 default router 176 hardware features 22 default VLAN 251 hardware requirements delay request interval 159 Device Manager 128 denial-of-service attack 221 Device Manager access web interface 129 hardware requirements 128 IEEE power classifications 227 overview 128 IGMP snooping software requirements 128...
Page 413 Index mode terminal adapter 396 SFP module 407 Access 248 straight-through cables Boundary 157 two twisted-pair 393 DHCP Server 174 DLR 168 dual power 154 attach power connector 111 EtherChannel 181 cable specifications 409 Forward 157 configure via Device Manager Web interface PoE 228 PTP 157 connect to port 113...
Page 414 Index Smartport roles applying 250 rear panel changing VLAN memberships 251 clearance 31 customization 251 Receive Detail tab, dashboard 285 optimize ports 248 recovery mismatch prevention 249 Smartport roles and NAT 189 firmware upgrade 310 switch software 310 Smartport roles and VLANs 256 redundancy SNMP EtherChannel 181...
Page 415 Index wire external alarms 111 VLAN memberships manage via Device Manager 128 changing 251 monitor prerequisite 251 alert log 282 VLANs port mirroring 215 assign to NAT instance 189 reset to factory defaults 310 status 278 default VLAN 262 troubleshoot 301 grouping different users 264 Device Manager display 305 isolate traffic 264...
Page 416 Index Notes: Rockwell Automation Publication 1783-UM007B-EN-P - March 2015...
Page 418 Rockwell Automation Support Rockwell Automation provides technical information on the Web to assist you in using its products. http://www.rockwellautomation.com/support you can find technical and application notes, sample code, and links to software service packs. You can also visit our Support Center at https://rockwellautomation.custhelp.com/ for software updates, support chats and forums, technical information, FAQs, and to sign up for product notification updates.

This manual is also suitable for:

Stratix 5700 Armorstratix 5700 1783-hms 1783-bms 1783-zms Stratix 8000 ... Show all

Allen-Bradley Stratix 5400 User Manual

Preface

Chapter 1 Ethernet/Ip CIP Interface

About the Switches

Install Stratix 5400 Switches

Chapter 2

Install Stratix 5700 Switches

Chapter 3

Chapter 4 Install Armorstratix 5700 Switches Overview

Install Armorstratix 5700 Switches

Install Stratix 8000 and 8300 Switches

Chapter 5

Chapter 6 Get Started Express Setup

Get Started

Configure Switch Features

Chapter 7 Configure Switch Features Alarms

Chapter 8 View Switch Status Via Device Manager

Monitor the Switch

Troubleshoot the Switch

Chapter 9 Troubleshoot the Installation

Data Types

Appendix A Stratix 5400 Data Types

Appendix B

Appendix C

Appendix D

Quick Links

Related Manuals for Allen-Bradley Stratix 5400

Summary of Contents for Allen-Bradley Stratix 5400