Page 1 User Manual Original Instructions Stratix Managed Switches Stratix 5400 Switches (1783-HMS) Stratix 5410 Switches (1783-IMS) Stratix 5700 Switches (1783-BMS) ArmorStratix 5700 Switches (1783-ZMS) Stratix 8000 and 8300 Switches (1783-MS, 1783-RMS, 1783-MX)
Page 2: Important User Information
Important User Information Read this document and the documents listed in the additional resources section about installation, configuration, and operation of this equipment before you install, configure, operate, or maintain this product. Users are required to familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws, and standards.
Page 3: Table Of Contents
Stratix 5400 Templates ........21...
Page 4 Table of Contents Configuration Files..........61 Manage Configuration Files via Device Manager .
Page 5 PRP Considerations ........213 Configure a Stratix 5400 or 5410 Switch as a RedBox..214 Configure Infrastructure Switches in LAN A and LAN B .
Page 6 Table of Contents Configure Port Thresholds via Device Manager ... . . 229 Configure Port Thresholds via the Logix Designer Application . . 230 Power over Ethernet (PoE)........232 Powered Device Detection and Initial Power Allocation .
Page 7 Table of Contents Chapter 4 Monitor the Switch Switch Status via Device Manager ......284 Front Panel .
Page 8 Port Numbering Stratix 5400 Port Numbering ....... . . 406 Stratix 5410 Port Numbering .
Page 9 Table of Contents Stratix 5400 and 5700 Cables and Connectors ....433 10/100 and 10/100/1000 Ports......433 Connect to 10BASE-T- and 100BASE-TX-Compatible Devices.
Page 10 Table of Contents Notes: Rockwell Automation Publication 1783-UM007I-EN-P - December 2017...
Page 11: Preface
Ethernet-to-the-Factory (EttF) solution and the Rockwell Automation Integrated Architecture™. The design guide focuses on the manufacturing industry. Stratix 5400 Ethernet Managed Switches Installation Instructions, publication 1783-IN014 Describes how to install the switches. Stratix 5410 Ethernet Managed Switches and Power Supply Installation Instructions, publication...
Page 12 Preface Notes: Rockwell Automation Publication 1783-UM007I-EN-P - December 2017...
Page 13 Chapter About the Switches Topic Page Stratix Managed Switches Stratix 5700 Lite Versus Full Firmware Features Software Features Hardware Features Memory Allocation Stratix® managed switches provide a secure switching infrastructure for harsh environments. You can connect the switches to network devices such as servers, routers, and other switches.
Page 14: About The Switches
Stratix Managed Switches The following table describes the Stratix managed switches. Switch Family Description Stratix 5400 switches Layer 2 and Layer 3 scalable managed switches. Available in 8…20 port versions, including all Gigabit port versions. Stratix 5410 switches Layer 2 and Layer 3 scalable managed switches.
Page 15: Stratix 5700 Lite Versus Full Firmware Features
About the Switches Chapter 1 Stratix 5700 Lite Versus Full The following table lists the features available for Stratix 5700 Full versus Lite firmware. All Stratix 8000 and ArmorStratix 5700 switches have Full firmware. Firmware Features To determine the firmware type available for specific catalog numbers, see the Stratix 5700 switch descriptions in Table 174 on page 415.
Page 16: Software Features
DHCP for ring devices Stratix 5400 switches • • Stratix 5700 switches ArmorStratix 5700 switches Enhanced Interior Gateway Routing Stratix 5400 switches with Layer 3 firmware • — Protocol (EIGRP) Stratix 5410 switches with Layer 3 firmware Stratix 8300 base units EtherChannels •...
Page 17 Stratix 5700 and ArmorStratix switches support PROFINET management via General Station Description (GSD) files Resilient Ethernet Protocol (REP) • — Routing, Layer 3 Stratix 5400 switches with Layer 3 firmware Stratix 5410 switches with Layer 3 firmware Stratix 8300 base units Routing, static and connected Stratix 5400 switches •...
Page 18: Hardware Features
To configure, monitor, and manage a switch, you can connect a switch to a computer through the console port: • Stratix 5400 and Stratix 5700 switches—Connect to the console port with an RJ45-to-DB-9 adapter cable or a mini USB cable. The mini USB driver is available in the firmware download section at http://www.rockwellautomation.com.
Page 19 PoE /PoE+ ports in any combination of PoE and PoE+. Stratix 5400 and ArmorStratix 5700 switches use one power connection for both basic power supply and PoE power supply. Stratix 5700 switches and Stratix 8000/8300 expansion modules require a dedicated power supply for PoE.
Page 20 Chapter 1 About the Switches Table 3 - Hardware Features for Stratix 5410 Switches (Continued) Feature Description Global navigation satellite Requires Stratix 5410 series B switches with IOS release 15.2(6)E0a and later. system (GNSS) Stratix 5410 series B switches have a built-in GNSS receiver that enables the switch to determine its own location and get an accurate time from a satellite constellation.
Page 21: Memory Allocation
Layer 2 firmware models have the IPv4 Default template. Layer 3 firmware models have these templates: • IPv4 Default • Dual IPv4/IPv6 Default • IPv4 Routing • Dual IPv4/IPv6 Routing Table 4 - Stratix 5400 Templates Feature Memory Allocation IPv4 Default Dual IPv4/IPv6 IPv4 Routing...
Page 22: Stratix 5410 Templates
Chapter 1 About the Switches Stratix 5410 Templates The selected template optimizes the resources in the switch to support features for eight routed interfaces and 1024 VLANs. Layer 2 firmware models have the Default template. Table 5 - Stratix 5410 Layer 2 Firmware Model Template Feature Memory Allocation Unicast MAC IDs...
Page 23: Stratix 5700 And Armorstratix 5700 Templates
About the Switches Chapter 1 Stratix 5700 and ArmorStratix 5700 Templates The following SDM templates are available: • Default • Lanbase Routing • Dual IPv4 and IPv6 If you enable static routing, or if you have more than 180 IGMP groups or multicast routes, consider using the routing template.
Page 24: Stratix 8000 And 8300 Templates
Chapter 1 About the Switches Stratix 8000 and 8300 Templates The following SDM templates are recommended: • Default • Lanbase Routing For static and connected routing, or if you have more than 180 IGMP groups or multicast routes, you can use the Lanbase Routing template. Other SDM templates are available, but are not covered in detail.
Page 25: Get Started
Chapter Get Started Topic Page Express Setup Overview Multi-mode Express Setup Single-mode Express Setup Configure Network Settings via Device Manager Configure Network Settings via the Logix Designer Application Default Global Macro Linx-based Software and Network Who Support Configuration via Device Manager Configuration via the Studio 5000 Environment User Administration via Device Manager Configuration Files...
Page 26: Express Setup Overview
(ArmorStratix™ 5700 switches) M12-to-RJ45 patchcord, such as Allen-Bradley® Short Press mode) catalog number 1585D-M4TBJM-2 For 1783-BMS4S2SGL or 1783-BMS4S2SGA switches, you also need a Gigabit copper SFP module, such as Allen-Bradley catalog number 1783-SFP1GSX, or a Gigabit fiber-to-Ethernet media converter. Rockwell Automation Publication 1783-UM007I-EN-P - December 2017...
Page 27: Express Setup Button
Get Started Chapter 2 Before you begin, do the following: • Single-mode Express Setup or multi-mode Express Setup in Short Press mode: – Disable other networks in your system. – Set your computer to determine its IP address automatically versus statically.
Page 28 Chapter 2 Get Started Stratix 5400 Switch Express Setup Button Stratix 5410 Switch Express Setup Button Stratix 5700 Switch Express Setup Button Rockwell Automation Publication 1783-UM007I-EN-P - December 2017...
Page 29 Get Started Chapter 2 ArmorStratix 5700 Switch Express Setup Button Stratix 8000/8300 Switch Express Setup Button Rockwell Automation Publication 1783-UM007I-EN-P - December 2017...
Page 30: Multi-Mode Express Setup
Chapter 2 Get Started Multi-mode Express Setup Multi-mode Express Setup has three modes: IMPORTANT The Studio 5000 Logix Designer® application supports only Medium-press mode. • Short Press mode—You want to use Express Setup to enter the initial IP address of the switch. You can then configure additional network settings via Device Manager.
Page 31: Run Multi-Mode Express Setup In Short Press Mode
Get Started Chapter 2 Run Multi-mode Express Setup in Short Press Mode Be aware of the following conditions that cause the switch to exit Short Press mode. Condition Status Indicator Behavior A non-default configuration exists on the switch. The Setup status indicator turns red for 10 seconds. You do not connect to the Express Setup port within 2 The unconnected port status indicator and the Setup minutes from when the port status indicator flashes...
Page 32: Run Multi-Mode Express Setup In Medium Press Mode
Chapter 2 Get Started 4. Connect a Category 5 Ethernet cable from the flashing switch port to the Ethernet port on a computer. For 1783-BMS4S2SGL or 1783-BMS4S2SGA switches, do one of the following: • Insert a copper SFP module into the Gi1/1 port on the switch. Then connect a Category 5 Ethernet cable from the SFP module to the Ethernet port on the computer.
Page 33: Run Multi-Mode Express Setup In Long Press Mode
Get Started Chapter 2 To run multi-mode Express Setup in Medium Press mode, follow these steps. 1. Apply power to the switch. When the switch powers on, it begins its power-on sequence. The power-on sequence can take as many as 90 seconds to complete. 2.
Page 34: Single-Mode Express Setup
Chapter 2 Get Started Single-mode Express Setup To run single-mode Express Setup, follow these steps. 1. Make sure that at least one switch Ethernet port is available for Express Setup. 2. Apply power to the switch. When the switch powers on, it begins its power-on sequence. The power-on sequence can take up to 90 seconds to complete.
Page 35: Configure Network Settings Via Device Manager
Get Started Chapter 2 Configure Network Settings You can apply one of the following setup modes to the switch after you run Express Setup as described on page via Device Manager • Express Setup—Enables the switch to operate as a managed switch with a default configuration that supports industrial automation applications.
Page 36 Chapter 2 Get Started Table 10 - PNP Mode Fields Field Description Management Interface (VLAN) The ID of the management VLAN through which the switch is managed. The management VLAN is the broadcast domain through which management traffic is sent between specific users or devices. It provides broadcast control and security for management traffic that must be limited to a specific group of users.
Page 37: Apply The Express Setup Configuration
Get Started Chapter 2 Apply the Express Setup Configuration To apply the Express Setup configuration to the switch, follow these steps. 1. Access Device Manager as described on page If the Express Setup page does not appear, try the following: •...
Page 38 Chapter 2 Get Started Table 11 - Express Setup Mode Fields Field Description Network Settings Host Name The name of the switch. Management Interface The ID of the management VLAN through which the switch is managed. The management VLAN is the broadcast domain through which (VLAN) management traffic is sent between specific users or devices.
Page 39 • For a statically assigned IP address, change it to the previously configured IP address. 7. For Stratix 5400 and 5410 switches, synchronize the SD card that came with the switch with the internal memory of the switch: • To synchronize the SD card via Device Manager, see page •...
Page 40: Configure Network Settings Via The Logix Designer Application
Chapter 2 Get Started Configure Network Settings To configure network settings via the Logix Designer application after running multi-mode Express Setup in Medium Press mode, follow these steps. via the Logix Designer Application 1. Add the switch to a controller project as described on page 2.
Page 41 Get Started Chapter 2 Table 12 - Express Setup Fields Field Description Internet Protocol (IP) Settings Click the method to use for assigning the swtich an IP address: • Manually Configure IP settings (default)—The switch uses a manually-assigned, static IP address. If you manually assign the IP address of the switch and your network uses a DHCP server, make sure that the IP address is not within the range of addresses that the DHCP server assigns.
Page 42: Default Global Macro
IMPORTANT For 1783-BMS4S2SGL or 1783-BMS4S2SGA switches, make sure that DC power is disconnected before disconnecting Ethernet cables. 8. For Stratix 5400 and Stratix 5410 switches, synchronize the SD card that came with the switch with the internal memory of the switch as...
Page 43: Linx-Based Software And Network Who Support
Get Started Chapter 2 Linx-based Software and The EtherNet/IP network interface also supports the List Identity command that is used by CIP-based network tools, such as the Linx-based software Network Who Support RSWho function. RSWho enables you to locate and identify your switch on the network by using the electronic data sheet (EDS) files.
Page 44: Data Accessible With Cip
Chapter 2 Get Started Data Accessible with CIP The CIP interface lets you access the information in Table Table 13 - Data Accessible with CIP Data Type Details Input data via I/O connection • Link status per port: not connected, connected •...
Page 45: Configuration Via Device Manager
Get Started Chapter 2 Configuration via Device Manager is a web-based management tool for configuring, monitoring, and troubleshooting individual switches. You can display Device Manager Device Manager from anywhere in your network through a web browser. Device Manager displays real-time views of switch configuration and performance.
Page 46: Access Device Manager
Chapter 2 Get Started Access Device Manager With IOS release 15.2(5)EA.fc4 and later, Device Manager provides a secure connection via the latest version of Internet Explorer or Firefox. Security messages from your browser can appear when you access Device Manager. To make sure that Device Manager runs properly, disable any popup blockers or proxy settings in your browser and any wireless clients on your computer.
Page 47 Get Started Chapter 2 3. (Firefox). If the following message appears, do the following: a. Click Advanced. b. Click Add Exception. Rockwell Automation Publication 1783-UM007I-EN-P - December 2017...
Page 48 Chapter 2 Get Started c. Click Confirm Security Exception. IMPORTANT Do not check Permanently store this exception. Permanently storing the exception can cause issues to arise. 4. On the Login page, enter the switch user name and password. Rockwell Automation Publication 1783-UM007I-EN-P - December 2017...
Page 49: Configure Port Settings
Get Started Chapter 2 Configure Port Settings The basic port settings determine how data is received and sent between the switch and the attached device. You can change these settings to fit your network needs and to troubleshoot network problems. The settings on a switch port must be compatible with the port settings of the connected device.
Page 50 Chapter 2 Get Started Table 16 - Port Settings Field Description Port Name The number of the switch port, including port type, such as Fa for Fast Ethernet and Gi for Gigabit Ethernet, and the specific port number: • Gi/1 is the gigabit port 1 of the switch. •...
Page 51: Configuration Via The Studio 5000 Environment
Get Started Chapter 2 Table 16 - Port Settings (Continued) Field Description Administrative Mode Choose one of the following administrative modes: • Access—The interface is in permanent nontrunking mode and negotiates to convert the neighboring link into a nontrunk link even if the neighboring interface is a trunk interface.
Page 52 Chapter 2 Get Started To add the switch to a controller project in the Logix Designer application, follow these steps. IMPORTANT These steps are required before you can go online to configure and monitor the switch. You must be online to view and configure most switch parameters in the Logix Designer application.
Page 53: General Properties
Get Started Chapter 2 General Properties To configure general properties, follow these steps. 1. In the navigation pane, click General and complete the fields. IMPORTANT Make sure that the IP address and host name match the values you used during Express Setup. On the Module Properties dialog box, you can choose either an IP address or host name.
Page 54 Chapter 2 Get Started 2. In the Module Definition area, click Change. 3. On the Module Definition dialog box, complete the fields and click Field Description Revision The major and minor revision of the switch: • Major revision: 1…128 • Minor revision: 1…255 Electronic Keying Choose one of the following: •...
Page 55: Connection Properties
Get Started Chapter 2 Connection Properties In the navigation pane, click Connection. Table 18 - Connection Fields Field Description Requested Packet Interval (RPI) Enter a value between 300…5000. Inhibit Module Check to disable communication between the controller and the switch. Clear the checkbox to restore communication.
Page 56: Switch Configuration
Chapter 2 Get Started Switch Configuration You can configure IP settings and administrative parameters. The IP address can be manually assigned (static) or it can be automatically assigned by a Dynamic Host Configuration Protocol (DHCP) server. The default is Static. We recommend that you choose Static and manually assign the IP address for the switch.
Page 57: Port Configuration
Get Started Chapter 2 Port Configuration Port settings determine how data is received and sent between the switch and the attached device. In the navigation pane, click Port Configuration. Table 20 - Port Configuration Fields Field Description Unit Indicates where the port resides: (Stratix 8000/8300 switches) •...
Page 58: Port States During Program Mode And Connection Faults
Chapter 2 Get Started Table 20 - Port Configuration Fields (Continued) Field Description Auto-negotiate If you want the port and end-device to auto-negotiate the link speed and Duplex mode, check the checkbox. To specify the desired port speed and Duplex mode manually, clear the checkbox. We recommend that you use the default (auto-negotiate) so that the speed and duplex settings on the switch port automatically match the setting on the connected device.
Page 59 Get Started Chapter 2 Table 21 - Fault/Program Action Fields Field Description Port Displays the port type and port number: • Fa—Fast Ethernet • Gi—Gigabit Ethernet • Te—10 Gigabit Ethernet Program Mode Choose what happens at the port when the controller transitions to Program mode: •...
Page 60: User Administration Via Device Manager
Chapter 2 Get Started User Administration via You can add, modify, or delete users and user login information for the switch via Device Manager. Device Manager From the Admin menu, choose Users. For each user, you can specify the information in Table Table 22 - Add User Fields Field...
Page 61: Configuration Files
Get Started Chapter 2 Configuration Files The switch configuration files (config.text and vlan.dat) are in ASCII human-readable format. This configuration file is stored in nonvolatile memory and is read into the random access memory (RAM) of the switch as the running configuration when the switch is powered up. When any changes are made to the configuration, the changes immediately take effect in the running configuration.
Page 62: Manage Configuration Files Via The Logix Designer Application
Chapter 2 Get Started Manage Configuration Files via the Logix Designer Application You can do the following: • Save the switch configuration to a file for archiving • Restore a switch configuration that is stored locally on the computer or within the Logix Designer application project.
Page 63: Secure Digital (Sd) Card
SD card. You must use the 1784-SD1 card available from Rockwell Automation with the switches. • Stratix 5400 and Stratix 5410 switches ship with an SD card, which stores the initial configuration and firmware for the switches. ATTENTION: If a non-Rockwell Automation SD card is used in Stratix switches, Rockwell Automation reserves the right to withhold support.
Page 64: Synchronize The Sd Card Via Device Manager
Chapter 2 Get Started If you start the switch from the SD card and then remove it while the switch is running, the following conditions apply: • Device Manager is no longer be accessible. • Changes that are made by using the CLI or the Logix Designer application take effect, but are not saved when the switch is restarted.
Page 65 Get Started Chapter 2 Table 23 - Manual Sync Tab Fields Field Description SD Card Status Indicates whether SD card is present, the status of the card, and from where its configuration was started. SD to Flash Sync Choose from these options: •...
Page 66 Chapter 2 Get Started Table 24 - Auto Sync Tab Fields Field Description Configuration Auto Sync—Automatically synchronize the configuration when a configuration change is made in Device Manager. Auto Sync is the default configuration. Prompt to Sync—After a configuration change, a message prompts you to confirm the synchronization. Manual Sync—No synchronization occurs on a configuration change unless it is done manually.
Page 67: Synchronize The Sd Card Via The Logix Designer Application
Get Started Chapter 2 Synchronize the SD Card via the Logix Designer Application You can synchronize the SD card to either the configuration file or the entire image. In the navigation pane, click SD Flash Sync. Table 25 - SD Flash Sync Fields Field Description SD Flash Status...
Page 68: Compactflash Memory Card
Chapter 2 Get Started CompactFlash Memory Card The CompactFlash card for Stratix 8000/8300 switches contains the switch IOS operating system, Device Manager firmware, and user-defined configuration settings. Without the CompactFlash card, the switch cannot power up or restart. If you remove the card with the switch running, the switch continues to function.
Page 69: Cisco Network Assistant
Get Started Chapter 2 With firmware revision 2.001 or later, the firmware is installed to the running nonvolatile memory location: • If you start the switch with the SD card inserted, the firmware is installed on the SD card. • If you start the switch from internal memory without the SD card inserted, the firmware is installed in the internal memory.
Page 70: Command-Line Interface
• To connect to the standard 9-pin serial port on a computer, use an RJ45-to-DB-9 adapter cable. • (Stratix 5400, 5410, 5700, and ArmorStratix 5700 switches). Use a standard mini-USB cable to connect to the mini-USB port on a computer. If you use the USB cable, download the drivers from http://www.rockwellautomation.com.
Page 71: Enable Ssh Or Telnet In Device Manager
Get Started Chapter 2 Enable SSH or Telnet in Device Manager SSH provides a secure, remote connection to the switch. SSH provides more security for remote connections than Telnet by providing strong encryption. IMPORTANT For secure network access, we recommend that you do not use Telnet. For new switch configurations with IOS release 15.2(5)EA.fc4 and later, Telnet is disabled by default.
Page 72 Chapter 2 Get Started Notes: Rockwell Automation Publication 1783-UM007I-EN-P - December 2017...
Page 73: Configure Switch Features
Chapter Configure Switch Features Topic Page Access Control Lists (ACLs) Alarms CIP Sync Time Synchronization (Precision Time Protocol) Cryptographic IOS Device Level Ring (DLR) Topology Dynamic Host Configuration Protocol (DHCP) Persistence Enhanced Interior Gateway Routing Protocol (EIGRP) EtherChannels Feature Mode Global Navigation Satellite System (GNSS) High-availability Seamless Redundancy (HSR) Horizontal Stacking...
Page 74: Access Control Lists (Acls)
Chapter 3 Configure Switch Features This chapter describes software features that you can configure via Device Manager, the Studio 5000 Logix Designer® application, or both. More software features are available. You can configure some features with the global macro or Smartports feature. For information about how to configure features not available in Device Manager or the Logix Designer application, see the documentation available at http://www.Cisco.com.
Page 75: Configure Acls Via Device Manager
Configure Switch Features Chapter 3 Configure ACLs via Device Manager The ACL page shows the standard and extended ACLs defined on the switch. Once you add an ACL to the ACL List tab, you can apply it to a port and specify a direction on the Apply ACL tab.
Page 76 Chapter 3 Configure Switch Features Field Description ACL Type Click Standard or Extended: • Standard (default)—Uses source addresses. • Extended—Uses source and destination addresses and optional protocol type information. ACL Name Type an alphanumeric name to identify the ACL. Named access lists are more convenient than numbered access lists because you can specify a meaningful name that is easier to remember and associate with a task.
Page 77 Configure Switch Features Chapter 3 Destination Type (Extended ACL only). Choose the type of the destination to which the packet is sent: • Host • Any • Network Dest Address (Extended ACL only). Type the network or host number to which the packet is sent. Dest Wildcard (Extended ACL only).
Page 78 Chapter 3 Configure Switch Features 1. From the ACL page, click the Apply ACL tab. 2. Click the row for a port name. 3. In the Inbound ACL column, choose the ACL from the list of configured ACLs. 4. In the Outbound ACL column, choose ACL from the list of configured ACLs.
Page 79: Alarms
Configure Switch Features Chapter 3 Alarms Alarms vary by switch model. Switch Alarm Description Stratix® 5400 switch The switch lets you connect two alarm inputs from external devices, such as a door or temperature gauge, to the alarm input port on the front panel of the switch.
Page 80: Configure Alarms Via Device Manager
Chapter 3 Configure Switch Features Configure Alarms via Device Manager The switch software monitors conditions on a per port or a global basis. If the conditions do not match the set parameters, an alarm or a system message is triggered. By default, the switch sends the system messages to a logging facility. You can configure the switch to send SNMP traps to an SNMP server.
Page 81 Configure Switch Features Chapter 3 Global Alarms From the Configure menu, choose Alarm Settings and click the Global tab. Table 26 - Global Tab Fields Field Description FCS Hysteresis (1-10) The frame check sequence (FCS) error hysteresis threshold determines when an alarm condition is cleared. This value is expressed as a percentage of fluctuation from the FCS bit error rate.
Page 82 Chapter 3 Configure Switch Features Port Alarms From the Configure menu, choose Alarm Settings and click the Port tab. For each port, choose an Alarm Profile and set the FCS threshold. The frame check sequence (FCS) error hysteresis threshold is expressed as a percentage of fluctuation from the FCS bit error rate.
Page 83 Configure Switch Features Chapter 3 On the Add/Edit Profile Instance page, you can configure the alarms and actions for an alarm profile. Table 27 - Add/Edit Profile Instance Fields Field Description Name A unique name for the alarm profile. Alarm Name These types of alarms can trigger an action.
Page 84: Cip Sync Time Synchronization (Precision Time Protocol)
Chapter 3 Configure Switch Features CIP Sync Time CIP Sync time synchronization refers to the IEEE 1588 standard for Precision Time Protocol (PTP). The protocol enables precise synchronization of clocks Synchronization in measurement and control systems. Clocks are synchronized with (Precision Time Protocol) nanosecond accuracy over the EtherNet/IP communication network.
Page 85: End To End Transparent Mode
All switch ports are PTP-enabled by default. Forward mode is the default mode. NTP-PTP Clock Mode NTP-PTP Clock mode is availabe in Stratix 5400 and 5410 switches. In NTP-PTP Clock mode, the switch functions as the Grandmaster clock and boundary clock: •...
Page 86: Configure Time Synchronization Via Device Manager
Chapter 3 Configure Switch Features Before you configure a switch to use NTP-PTP clock mode, do the following: • Configure NTP as described on page 201. While NTP-PTP Clock mode requires only one NTP time source, as a best practice, we recommend you configure two or more NTP time sources.
Page 87 Configure Switch Features Chapter 3 4. To complete the remaining fields, refer to the figure and table that corresponds to your mode. Mode Page Boundary End to End Forward NTP-PTP Clock Figure 1 - Boundary Mode Table 28 - Boundary Mode Fields Field Description PTP Clock Settings...
Page 88 Chapter 3 Configure Switch Features Table 28 - Boundary Mode Fields (Continued) Field Description Clock Quality Displays a summary of the quality of the Grandmaster clock: • Class—Time and frequency traceability of the Grandmaster clock. • Accuracy—Expected accuracy of the Grandmaster clock when the Best Master Clock algorithm is in use. •...
Page 89 Configure Switch Features Chapter 3 Table 28 - Boundary Mode Fields (Continued) Field Description Announce Interval Type the time interval, specified as the logarithmic mean in seconds, for sending announce messages. Valid values: • 0—1 second • 1—2 seconds • 2— 4 seconds •...
Page 90 Chapter 3 Configure Switch Features Table 29 - End to End Transparent Mode Fields (Continued) Field Description Per Port Settings Port Name Displays the port type and port number: • Fa—Fast Ethernet • Gi—Gigabit Ethernet • Te—10 Gigabit Ethernet State Displays the synchronization state of the switch port with the parent or Grandmaster clock: (Not available on •...
Page 91 Configure Switch Features Chapter 3 Table 29 - End to End Transparent Mode Fields (Continued) Field Description Sync Interval Type the time interval, specified as the logarithmic mean in seconds, for sending synchronization messages. (Not available on Valid values: Stratix 8000/8300 switches) •...
Page 92 Chapter 3 Configure Switch Features Figure 4 - NTP-PTP Clock Mode Table 31 - NTP-PTP Clock Mode Fields Field Description PTP Clock Settings PTP Device Type Displays the PTP clock type of the switch, as determined by the Mode setting. Number of PTP ports Displays the number of ports assigned to the PTP clock.
Page 93 Configure Switch Features Chapter 3 Table 31 - NTP-PTP Clock Mode Fields (Continued) Field Description Time Source Displays the time source used by the Grandmaster clock. Device Clock Details Device Time Source Displays the time source used by the switch. Device Clock Time Displays the time on the switch, obtained from the time source.
Page 94: Configure Time Synchronization Via The Logix Designer Application
Chapter 3 Configure Switch Features Table 31 - NTP-PTP Clock Mode Fields (Continued) Field Description Sync Interval Type the time interval, specified as the logarithmic mean in seconds, for sending synchronization messages. Valid values: • -1—half second • 0—1 second •...
Page 95 Configure Switch Features Chapter 3 Figure 5 - Boundary Mode Table 32 - Boundary Mode Field Description Clock Identity Displays a unique identifier for the clock. Grandmaster Selection Priority1 Type a value to override the default criteria (clock quality, clock class, and so on) for the best master clock selection. A lower value takes precedence.
Page 96 Chapter 3 Configure Switch Features Table 32 - Boundary Mode (Continued) Field Description Delay Request The logarithmic mean interval in seconds. Type the recommended to connected devices to send delay request messages when the switch port is in the master state. Valid values: •...
Page 97 Configure Switch Features Chapter 3 Figure 6 - End-to-End Transparent Mode Table 33 - End to End Transparent Mode Fields Field Description Port Displays the port type and port number: • Fa—Fast Ethernet • Gi—Gigabit Ethernet • Te—10 Gigabit Ethernet Enable Check the checkbox for each port on which to enable PTP.
Page 98 Chapter 3 Configure Switch Features Figure 8 - NTP-PTP Mode Table 34 - NTP-PTP Mode Fields Field Description Clock Identity Displays a unique identifier for the clock. Grandmaster Selection Type a value to override the default criteria (clock quality, clock class, and so on) for the best master clock selection. A lower value takes Priority1 precedence.
Page 99: View Time Sync Information In The Logix Designer Application
Configure Switch Features Chapter 3 Table 34 - NTP-PTP Mode Fields (Continued) Field Description Delay Request Interval Type the recommended to connected devices to send delay request messages when the switch port is in the master state. Valid values: • -1—half second •...
Page 100 Chapter 3 Configure Switch Features Figure 9 - Time Sync Information Table 35 - Time Sync Information Fields Field Description CIP Sync Time Synchronization Displays whether the Precision Time Protocol is enabled or disabled on the device. UTC System Time Displays the current system time in units of microseconds.
Page 101: Cryptographic Ios
Configure Switch Features Chapter 3 Table 35 - Time Sync Information Fields (Continued) Field Description Class Displays a measure of the quality of the local clock. Values are defined from 0…255 with 0 as the best clock. Accuracy Indicates the expected absolute accuracy of the local clock relative to CIP Sync time synchronization epoch (31 December, 1969 23:59:51.99918 UTC).
Page 102: Device Level Ring (Dlr) Topology
Chapter 3 Configure Switch Features Device Level Ring (DLR) You can configure a DLR topology on Stratix 5400 switches and some models of Stratix 5700 and ArmorStratix 5700 switches. For a list of switches that Topology support a DLR topology, see...
Page 103 IMPORTANT Stratix 5700 and ArmorStratix 5700 switches support only one ring per switch. Stratix 5400 switches support as many as three rings per switch. The rings can share the same VLAN, or each ring can be on its own VLAN.
Page 104: Dlr Port Choices
• Stratix 5700 and ArmorStratix 5700 switches support one ring and two DLR-enabled ports per switch. • Stratix 5400 switches support as many as three rings and six DLR-enabled ports per switch. We recommend that you use the Multiport Automation Device Smartport role on ports you configure for DLR.
Page 105: Dlr Considerations
Configure Switch Features Chapter 3 Table 37 - DLR Port Choices for Stratix 5700 and ArmorStratix 5700 Switches Switch Port 1783-BMS20CGL Fa 1/15 Fa 1/16 Gi 1/1 Gi 1/2 Fa 1/17 Fa 1/18 1783-BMS20CGP Fa 1/15 Fa 1/16 Gi 1/1 Gi 1/2 Fa 1/17 Fa 1/18...
Page 106: Redundant Gateways
Chapter 3 Configure Switch Features Redundant Gateways Stratix 5400, Stratix 5700, ArmorStratix 5700 switches that support DLR also support redundant gateways. IMPORTANT Redundant gateways do not work with End to End Transparent mode for Precision Time Protocol. For more information about End to End Transparent...
Page 107 Configure Switch Features Chapter 3 Figure 11 shows an example of a switch configured for redundant gateway. All ports are assigned to VLAN 1. Figure 11 - Redundant Gateway Switch Ports Port Configuration DLR access port DLR access port Redundant gateway uplink port Redundant gateway uplink port Non-DLR port When the switch acts as the active redundant gateway, traffic on the switch...
Page 108 Chapter 3 Configure Switch Features Figure 12 - Traffic from Backup Gateway to Ring Switch Switch Switch Switch DLR Device DLR Active DLR Backup Gateway Gateway DLR Active Supervisor Rockwell Automation Publication 1783-UM007I-EN-P - December 2017...
Page 109 Configure Switch Features Chapter 3 You can configure redundant gateways on switches that are either ring supervisors or ring nodes. Figure 13 shows two Stratix 5700 switches that are configured as ring supervisors with redundant gateway: • One switch is configured as the active ring supervisor and also the active redundant gateway.
Page 110 Chapter 3 Configure Switch Features Figure 14 shows two Stratix 5700 switches that are configured as ring nodes with redundant gateway: • One switch is a ring node and the active redundant gateway. • The other switch is a ring node and the backup redundant gateway. In this example, the switch provides redundant gateway functionality, so that all ring nodes have access to the outside network.
Page 111: Dhcp For Ring Devices
Configure Switch Features Chapter 3 DHCP for Ring Devices Stratix 5400, Stratix 5700, and ArmorStratix 5700 switches that support DLR also support DHCP for ring devices. IMPORTANT DHCP for ring devices does not work with DHCP peristence as described on page 131.
Page 112 Chapter 3 Configure Switch Features DHCP snooping for a ring can be enabled or disabled. By default, DHCP snooping for a ring is enabled: • When enabled, DHCP snooping restricts DHCP address assignments from going beyond an active ring DCHP server and the devices within the ring.
Page 113 Configure Switch Features Chapter 3 In this example, the active ring DHCP server recognizes IP address requests from ring devices 3, 4, and 6 and responds with the position-based IP address specified in the DHCP table (Table 38). The ring device index numbers in the DCHP table begin incrementing in order from the device connected to the lowest DLR port.
Page 114: Multiple Rings
• All ring ports within the same ring or belonging to different rings must be assigned to the same access VLAN. • The same Stratix 5400 switch must serve as the active gateway for all rings. • The same Stratix 5400 switch must serve as the backup gateway for all rings.
Page 115: Configure Dlr Via Device Manager
To configure DLR, follow these steps. 1. From the Configure menu, choose DLR. 2. (Stratix 5400 switches only). From the DLR Ring ID pull-down menu, choose the ring to configure. 3. To configure the switch as a ring node or a ring supervisor, complete the...
Page 116 Chapter 3 Configure Switch Features Table 39 - Config DLR Fields Field Description Mode Choose one of these modes: • Disabled—The DLR feature is disabled on the switch. • Node—The switch is a ring node. • Supervisor—The switch is a ring supervisor. Default: Disabled Port1 Choose a ring port.
Page 117 Configure Switch Features Chapter 3 Table 40 - Config DHCP Fields Field Description Ring DHCP Server Enable Check the checkbox to enable the ring DHCP server on the DLR supervisor device. Role Choose a role to assign to the ring DHCP server. Valid values: •...
Page 118 Chapter 3 Configure Switch Features Assign IP Addresses to Ring Devices Use the table on the Config DHCP tab to assign IP addresses to devices based on their position in the ring. To add IP addresses individually, click Add Entry. Field Description Index...
Page 119: Configure Dlr Via The Logix Designer Application
Configuration parameters appear for the number of available rings: • Stratix 5700 and ArmorStratix 5700 switches show one ring. • Stratix 5400 switches show three rings. Configure each ring: • To enable DLR on specified ring ports and to view information about...
Page 120 Chapter 3 Configure Switch Features Table 41 - Device Level Ring (DLR) Fields Field Description Enable Ring 1/Enable Ring 2/Enable Ring 3 Check to enable DLR on the ports that are specified in the associated Port 1 and Port 2 fields for the ring. Port 1 Choose a ring port.
Page 121 Configure Switch Features Chapter 3 Table 41 - Device Level Ring (DLR) Fields (Continued) Field Description Active Ring Supervisor Displays the IP address of the active ring supervisor. DCHP Server Role Displays the role of the ring DHCP server. Valid values: •...
Page 122 Chapter 3 Configure Switch Features Table 42 - Ring 1/Ring 2/Ring 3 Fields (Continued) Field Description Active Supervisor Precedence Displays the precedence that is assigned to the ring supervisor. You assign the precedence value on the Advanced Network Configuration dialog box. See Table Enable Supervisor Mode Check to make the switch a ring supervisor.
Page 123 Configure Switch Features Chapter 3 Table 43 - Advanced Network Configuration Fields Field Description Beacon Interval Type an interval for the supervisor to transmit beacon frames. Valid values: 200…100,000 µs The default interval is 400 µs. Beacon Timeout Type the amount of time ring nodes wait before timing out in the absence of received beacon messages. Valid values: 400…500,000 µs The default timeout is 1960 µs.
Page 124 Chapter 3 Configure Switch Features Table 44 - Redundant Gateway Configuration Fields (Continued) Field Description Precedence Choose a role to assign to the redundant gateway that corresponds to a predefined precedence value. The switch transmits the precedence value is advertise messages and is used to select the redundant gateway when multiple redundant gateways are configured. A higher value means higher precedence.
Page 125: Dhcp Server
Configure Switch Features Chapter 3 Table 45 - DHCP Fields Field Description IP Address Displays the IP address of the ring member. The IP address is reserved for the selected port and is not available for normal DHCP assignment. The IP address must be an address from the pool specified in DHCP IP address pool. To assign IP addresses to ring members, see Refer to Assign IP Addresses to Ring Members on page 125.
Page 126 Chapter 3 Configure Switch Features 2. From the DHCP Pool field, choose the name of the IP address pool to use for ring devices. This pool must be previously configured as described on page 132. DHCP persistance and DHCP for ring devices can coexist, but cannot share the same pool.
Page 127: Dynamic Host Configuration Protocol (Dhcp) Persistence
Configure Switch Features Chapter 3 Dynamic Host Configuration Every device in an IP-based network must have a unique IP address. DHCP assigns IP address information from a pool of available addresses to newly Protocol (DHCP) Persistence connected devices (DHCP clients) in the network. If a device leaves and then rejoins the network, the device receives the next available IP address, which is not necessarily the same address that it had before.
Page 128 Chapter 3 Configure Switch Features If you are using DHCP persistence, we recommend that you initially assign static IP addresses to end devices. If an end device fails and is replaced, the DHCP persistence feature assigns an IP address from the DHCP persistence table.
Page 129: Configure Dhcp Persistence Via Device Manager
Configure Switch Features Chapter 3 Configure DHCP Persistence via Device Manager To configure DHCP persistence, complete this process. 1. Configure the DHCP server. 2. Configure the IP address pool. 3. Assign an IP address to a switch port. Configure the DHCP Server. 1.
Page 130 Chapter 3 Configure Switch Features Configure the DHCP IP Address Pool Once DHCP is enabled, you can create the DHCP address pool. 1. From the Configure menu, choose DHCP. 2. Click Add. 3. Complete the fields and click OK. Field Description DHCP Pool Name The name of the DHCP IP address pool that is configured on the switch.
Page 131 Configure Switch Features Chapter 3 Field Description Domain Name The domain name for the DHCP client. The name can have up to 31 alphanumeric characters. The name cannot contain a ? or a tab. DNS Server The IP addresses of the domain name system (DNS) IP servers available to a DHCP client. The format is a 32-bit numeric address that is written as four numbers that are separated by periods.
Page 132: Configure Dhcp Persistence Via The Logix Designer Application
Chapter 3 Configure Switch Features Configure DHCP Persistence via the Logix Designer Application To configure DHCP persistence, complete this process. 1. Configure the DHCP server. 2. Configure the IP address pool. 3. Assign an IP address to a switch port. Configure the DHCP Server 1.
Page 133 Configure Switch Features Chapter 3 Configure the DHCP IP Address Pool Once DHCP is enabled, you can create the DHCP address pool. 1. In the navigation pane, click DHCP Pools. 2. Click New Pool. Rockwell Automation Publication 1783-UM007I-EN-P - December 2017...
Page 134 Chapter 3 Configure Switch Features 3. Complete the fields and click Close. Table 48 - Add/Edit DCHP Pool Definition Fields Field Description DHCP Pool Name The name of the DHCP IP address pool that is configured on the switch. A DHCP IP address pool is a range (or pool) of available IP addresses that the switch can assign to connected devices. DHCP Pool Network The subnetwork IP address of the DHCP IP address pool.
Page 135 Configure Switch Features Chapter 3 Table 48 - Add/Edit DCHP Pool Definition Fields (Continued) Field Description Primary DNS Address The IP addresses of the primary domain name system (DNS) IP servers available to a DHCP client. Secondary DNS Address The IP addresses of the secondary domain name system (DNS) IP servers available to a DHCP client. Primary WINS Address The IP address of the primary Microsoft NetBIOS name server (WINS server) available to a DHCP client.
Page 136: Enhanced Interior Gateway Routing Protocol (Eigrp)
DHCP Pool Name field. EIGRP is available on the following switches: Enhanced Interior Gateway • Stratix 5400 with Layer 3 firmware Routing Protocol (EIGRP) • Stratix 5410 with Layer 3 firmware •...
Page 137: Configure Eigrp Via Device Manager
Configure Switch Features Chapter 3 EIGRP uses the Diffusing Update Algorithm (DUAL), which provides loop-free operation at every instance throughout a route computation. DUAL allows all devices that are involved in a topology change to synchronize simultaneously. Routers that are not affected by topology changes are not involved in recomputations.
Page 138 Chapter 3 Configure Switch Features Table 50 - EIGRP Fields (Continued) Field Description Interface Choose a Layer 3 interface that is associated with the EIGRP ID. Hello Interval Type the hello interval for the EIGRP interface instance. Valid values: 1…65535 Default: 60 seconds for low-speed nonbroadcast multiaccess (NBMA) networks and 5 seconds for all other networks Hold Time Type the hold time interval for an EIGRP routing process.
Page 139 Configure Switch Features Chapter 3 Table 50 - EIGRP Fields (Continued) Field Description Loading Type a number that represents the effective bandwidth of the route. Valid values: 1…255 where 255 is 100 percent loading Type the smallest allowed value for the maximum transmission unit (MTU) in bytes. Valid values: 1…65535 Static Neighbor—EIGRP hello packets are sent as multicast packets.
Page 140 Chapter 3 Configure Switch Features Table 51 - Customize EIGRP Parameters Field Description EIGRP ID (Not editable). Displays the Autonomous System (AS) number of the EIGRP routing process. Auto-Summary Check the checkbox to allow the automatic summarization of subnet routes into network-level routes. This feature is disabled by default (the software sends subprefix routing information across classful network boundaries).
Page 141 Configure Switch Features Chapter 3 Table 51 - Customize EIGRP Parameters (Continued) Field Description Delay Type a route delay in tens of microseconds. Valid values: 1 or any positive number that is a multiple of 39.1 nanoseconds Type the smallest allowed value for the maximum transmission unit (MTU), in bytes. Valid values: 1…65535 Adjacency Changes Log Neighbor Changes...
Page 142: Etherchannels
Each EtherChannel can consist of up to eight compatible, configured Ethernet ports. Table 52 - EtherChannels by Switch Switch EtherChannels, max Stratix 5400 Stratix 5410 Stratix 5700 ArmorStratix 5700 Stratix 8000/8300 (1) EtherChannels are available only on swithes with Full firmware.
Page 143 Configure Switch Features Chapter 3 Figure 18 shows two EtherChannels. Two full-duplex 10/100/1000-Mbps ports on Switches A and C create an EtherChannel with a bandwidth of up to 4 Gbps between both switches. Similarly, two full-duplex 10/100 ports on Switches B and D create an EtherChannel with a bandwidth of up to 400 Mbps between both switches.
Page 144: Configure Etherchannels Via Device Manager
Chapter 3 Configure Switch Features Configure both ends of the EtherChannel in the same mode: • When you configure one end of an EtherChannel in PAgP or LACP mode, the system negotiates with the other end of the channel to determine the ports to become active.
Page 145 Configure Switch Features Chapter 3 You can add, edit, or delete an EtherChannel: • To add an EtherChannel, click Add. Complete the fields described in Table 55 and click OK. • To edit an EtherChannel, click the radio button next to the EtherChannel and click Edit.
Page 146 Chapter 3 Configure Switch Features Table 56 - Modify Channel Settings Dialog Box Field Description Channel Name Displays the name assigned to the channel. Description Type a description of the channel. Administrative Check Enable to make the channel active. Clear Enable to make the channel inactive. Speed Choose the operating speed of the channel.
Page 147: Configure Etherchannels Via The Logix Designer Application
Configure Switch Features Chapter 3 Configure EtherChannels via the Logix Designer Application In the navigation pane, click EtherChannels. You can add, edit, and delete EtherChannel members. Table 57 - EtherChannels Fields Field Description EtherChannel A number to identify the EtherChannel. See Table 52 for the maximum number of EtherChannels available per switch.
Page 148 Chapter 3 Configure Switch Features Rockwell Automation Publication 1783-UM007I-EN-P - December 2017...
Page 149: Feature Mode
Configure Switch Features Chapter 3 Feature Mode Feature mode is available on Stratix 5400 switches. Feature mode provides efficient allocation of resources on the switch to support the operation of multiple, time-sensitive features. There are two modes, each with a profile customized for certain features: •...
Page 150: Global Navigation Satellite System (Gnss)
Chapter 3 Configure Switch Features Global Navigation IMPORTANT GNSS is supported only on Stratix 5410 series B switches with IOS release Satellite System (GNSS) 15.2(6)E0a and later. To use the GNSS software feature on the switch, you must obtain an external GPS antenna from a third-party manufacturer.
Page 151: Gnss Signaling
Configure Switch Features Chapter 3 GNSS Signaling There are two stages in the process for the GNSS receiver to acquire satellites and provide timing signals to the host system: • Self-survey mode—On reset, the GNSS receiver comes up in Self-survey mode and attempts to lock on to a minimum of four different satellites to obtain a 3-D fix on its current position.
Page 152: Gnss Considerations
Clock mode, and three satellites are required for the first fix in Self-survey mode. • Disabled—Only one satellite is required for a valid timing fix. High-availability HSR is available on Stratix 5400 switches. HSR is defined in International Standard IEC 62439-3-2016 clause 5. Seamless Redundancy (HSR) For instructions on how to configure HSR via the CLI, refer to documentation available at http://www.Cisco.com.
Page 153: Horizontal Stacking
Configure Switch Features Chapter 3 Horizontal Stacking Horizontal stacking lets you manage as many as four Stratix 5410 switches as one logical device. To stack multiple switches, you connect the switches via as many as two uplink Ethernet ports per switch. You use the CLI to configure network ports as designated stack ports.
Page 154 Chapter 3 Configure Switch Features Figure 20 - Switch Stack in a Ring Topology 32648-M Figure 21 - Switch Stack in a Linear Topology 32649-M Table 58 lists the supported features for horizontal stacking. Table 58 - Supported Features Feature Type Support Layer 2 features •...
Page 155: Internet Group Management Protocol (Igmp) Snooping With Querier
Table 59 - Default Supported Multicast Groups Switch Default Multicast Groups Stratix 5400 and Stratix 5410 switches 1024 Stratix 5700 and ArmorStratix 5700 switches If you exceed 180 multicast groups, we recommend that you switch to the routing SDM template via Device Manager.
Page 156: Configure Igmp Snooping Via Device Manager
Chapter 3 Configure Switch Features Configure IGMP Snooping via Device Manager From the Configure menu, choose IGMP Snooping: • To enable IGMP snooping for all VLAN IDs, check Enable next to IGMP Snooping. • To enable IGMP Querier for all VLAN IDs, check Enable next to IGMP Querier.
Page 157: Maximum Transmission Unit (Mtu)
Configure Switch Features Chapter 3 Maximum Transmission Unit The MTU defines the largest size of frames that an interface can send or receive in a single network transaction. (MTU) In Device Manager, you can change the following MTU settings on the switch: •...
Page 158: Motion Prioritized Qos Macros
QoS Step 1 and Motion Prioritized QoS Step 2 macros. If you enable only one macro, the QoS settings applied during Express Setup remain active. Stratix 5700, ArmorStratix 5700, and Stratix 8000 Switches Stratix 5400 and 5410 Switches Rockwell Automation Publication 1783-UM007I-EN-P - December 2017...
Page 159: Netflow Lite
Chapter 3 NetFlow Lite NetFlow Lite is available on Stratix 5400 and 5410 switches. NetFlow Lite uses flows to provide statistics for accounting, network monitoring, and network planning. A flow is unidirectional stream of packets that arrives on a source interface and has the same values for the keys.
Page 160: Configuration Overview
Chapter 3 Configure Switch Features Configuration Overview To configure NAT, you create one or more unique NAT instances. A NAT instance contains entries that define each address translation and other configuration parameters. IMPORTANT Before you create NAT instances, configure all Smartport roles and VLANs. The translations that you define depend on whether traffic is routed through a Layer 3 switch or router or a Layer 2 switch.
Page 161 Figure 22 - Layer 3 Example with NAT in Stratix 5700 Switch HMI 10.200.1.2 VLAN 200 VLAN 200 Line Controller 10.200.1.3 Stratix 5400 with Layer 3 Firmware Controller 1 to Line Controller VLAN 10: 10.10.1.1 NAT Gateway: 192.168.1.1 VLAN 200: 10.200.1.1 Controller 2 to Line Controller...
Page 162 Chapter 3 Configure Switch Features Figure 23 - Layer 3 Example with NAT in Stratix 5410 Layer 3 Firmware Model HMI 10.200.1.2 VLAN 200 VLAN 200 Line Controller 10.200.1.3 Stratix 5410 with Layer 3 Firmware VLANs 10...80: 10.10.1.1...10.10.8.1 Controllers 1...8 communicate NAT Gateway: 192.168.1.1 with each other and the line controller.
Page 163 Figure 24 - Layer 2 Example with NAT in Stratix 5700 Switch HMI 10.10.1.101 Line Controller VLAN 10 VLAN 10 10.10.1.100 192.168.1.100 Controller 1 to Line Controller Stratix 5400 Layer 2 Firmware Model VLAN 10: 10.10.1.1 Controller 2 to Line Controller VLAN 10 VLAN 10 Machine 1 Mach chin...
Page 164 Chapter 3 Configure Switch Features Figure 25 - Layer 2 Example with NAT in Stratix 5410 Layer 2 Firmware Model HMI 10.10.1.101 Line Controller VLAN 10 VLAN 10 10.10.1.100 192.168.1.100 Controllers 1...8 communicate Stratix 5410 Layer 2 Firmware Model with each other and the line controller. with NAT VLAN 10: 10.10.1.1 NAT Instances on NAT Ports 1...8...
Page 165 Table 63 - Maximum Translation Entries Switch Maximum Translation Entries Stratix 5400 and Stratix 5700 128 across all NAT ports. Stratix 5410 128 across NAT ports 1…6 and 13…18. 128 across NAT ports 7…12, 19…24, and 25…28.
Page 166: Vlan Assignments
Chapter 3 Configure Switch Features VLAN Assignments When configuring NAT, you can assign one or more VLANs to a NAT instance. When you assign a VLAN to a NAT instance, the traffic that is associated with that VLAN is subject to the configuration parameters of the NAT instance.
Page 167: Configuration Considerations
• All switches can translate only IPv4 addresses. • All switches can have a maximum of 128 NAT instances. • Switch-specific features are shown in the following table. Feature Stratix 5700 Switch Stratix 5400 Switch Stratix 5410 Switch Uplink Ports Downlink Ports Translation Entries (1) A subnet translation counts as only one translation entry, but includes translations for many devices (2) Both uplink and downlink ports can be configured for as many as 8 NAT ports.
Page 168: Traffic Permits And Fixups
Chapter 3 Configure Switch Features Traffic Permits and Fixups While a NAT-configured port can translate many types of traffic, only unicast and broadcast traffic are supported. You can choose to block or pass through the following unsupported traffic types: • Untranslated unicast traffic •...
Page 169 Configure Switch Features Chapter 3 Create NAT Instances for Traffic Routed through a Layer 3 Switch or Router 1. From the Configure menu, choose NAT to display the NAT page. 2. Click Add to display the General tab of the Add/Edit NAT Instance page.
Page 170 Chapter 3 Configure Switch Features VLAN Selection for Stratix 5700 and 5400 Switches VLAN Selection for Stratix 5410 Switches Rockwell Automation Publication 1783-UM007I-EN-P - December 2017...
Page 171 Configure Switch Features Chapter 3 3. In the Name field, type a unique name to identify the instance. The instance name cannot include spaces or exceed 32 characters. 4. Complete VLAN assignments: • (Stratix 5700 and 5400 switches) For each uplink port on the right, select each VLAN to assign to the instance.
Page 172 Chapter 3 Configure Switch Features Field Description Public IP Address Type a public IP address: • To translate one address, type a unique public address to represent the device. • To translate a range of addresses, type the first address in the range of sequential addresses. •...
Page 173 Configure Switch Features Chapter 3 Create NAT Instances for Traffic Routed through a Layer 2 Switch 1. From the Configure menu, choose NAT to display the NAT page. 2. Click Add to display the General tab of the Add/Edit NAT Instance page.
Page 174 Chapter 3 Configure Switch Features VLAN Selection for Stratix 5700 and 5400 Switches VLAN Selection for Stratix 5410 Switches Rockwell Automation Publication 1783-UM007I-EN-P - December 2017...
Page 175 Configure Switch Features Chapter 3 3. In the Name field, type a unique name to identify the instance. The instance name cannot include spaces or exceed 32 characters. 4. Complete VLAN assignments: • (Stratix 5700 and 5400 switches) For each uplink port on the right, select each VLAN to assign to the instance.
Page 176 Chapter 3 Configure Switch Features Field Description Public IP Address Type a public IP address: • To translate one address, type a unique public address to represent the device. • To translate a range of addresses, type the first address in the range of sequential addresses. •...
Page 177 Configure Switch Features Chapter 3 6. Click the Public to Private tab. 7. Click Add Row, complete the fields, and click Save. Field Description Public IP Address Type a public IP address: • To translate one address, type the existing address for the device on the public subnet. •...
Page 178 Chapter 3 Configure Switch Features Field Description Private IP Address Type a private IP address: • To translate one address, type a unique private address to represent the device. • To translate a range of addresses, type the first address in the range of sequential addresses. •...
Page 179 Configure Switch Features Chapter 3 Configure Traffic Permits and Fixups Use caution when you configure traffic permits and fixups. We recommend that you use the default values. 1. Click the Advanced tab. 2. Choose one of these options for incoming and outgoing packets that are not handled by NAT: •...
Page 180: Configure Nat Via The Logix Designer Application
Chapter 3 Configure Switch Features Configure NAT via the Logix Designer Application For Stratix 5410 switches, see page 192. In the navigation pane, click NAT. Table 64 - NAT Fields Field Description Instance Name Displays the unique name of the NAT instance. Gi1/1 VLANs Displays the VLANs assigned to each NAT instance on port Gi1/1.
Page 181 Configure Switch Features Chapter 3 To configure NAT, follow one of these procedures that are based on your application: • Create NAT Instances for Traffic Routed through a Layer 3 Switch or Router For an example of this application, see Figure 23 on page 162.
Page 182 Chapter 3 Configure Switch Features 2. In the Name field, type a unique name to identify the instance. The instance name cannot include spaces or exceed 32 characters. 3. In the VLAN Association area, check the checkbox next to each VLAN to assign to the instance.
Page 183 Configure Switch Features Chapter 3 Table 66 - Range Translation Field Description Type of Entry Choose Range. Starting Private IP Address Type the existing starting address for the device on the private subnet. Starting Public IP Address Type a unique, starting public address to represent the device. Range Type the number of addresses to include in the range.
Page 184 Chapter 3 Configure Switch Features Table 67 - Subnet Translation (Continued) Field Description Subnet Mask Choose the subnet mask for the addresses to translate. Valid values: • Class B: 255.255.0.0 • Class C: 255.255.255.0 • Portion of Class C: – 255.255.255.128 (provides 128 addresses per translation entry –...
Page 185 Configure Switch Features Chapter 3 Create NAT Instances for Traffic Routed through a Layer 2 Switch 1. From the NAT view, click New Instance to display the General tab. 2. In the Name field, type a unique name to identify the instance. The instance name cannot include spaces or exceed 32 characters.
Page 186 Chapter 3 Configure Switch Features • To translate one address for a device on the private subnet that communicates on the public subnet, see Table • To translate a range of addresses for devices on the private subnet that communicates on the public subnet, see Table 69 •...
Page 187 Configure Switch Features Chapter 3 Table 70 - Subnet Translation Field Description Type of Entry Choose Subnet. Starting Private IP Address Type the existing starting address for a device on the private subnet. This address must correspond to the size of the subnet mask to translate. Subnet Mask Starting Private Subnet Address 255.255.0.0...
Page 188 Chapter 3 Configure Switch Features 6. Click OK. 7. Click the Public to Private tab. 8. Click New Entry to display the New Entry dialog box. 9. Do one of the following: • To translate one address for a device on the public subnet that communicates on the private subnet, see Table •...
Page 189 Configure Switch Features Chapter 3 Table 71 - Single Translation Field Description Type of Entry Choose Single. Single is the default value. Starting Public IP Address Type the existing address for the device on the public subnet. Starting Private IP Address Type a unique private address to represent the device.
Page 190 Chapter 3 Configure Switch Features Table 73 - Subnet Translation (Continued) Field Description Starting Private IP Address Type a unique, starting private address to represent the devices. This address must correspond to the size of the subnet mask to translate. Subnet Mask Starting Private Subnet Address 255.255.0.0...
Page 191 Configure Switch Features Chapter 3 Configure Traffic Permits and Fixups Use caution when you configure traffic permits and fixups. We recommend that you use the default values. 1. Click the Advanced tab. 2. In the Traffic Permits table, choose one of these options for unsupported incoming and outgoing packets: •...
Page 192: Configure Nat Via The Logix Designer Application
Chapter 3 Configure Switch Features Configure NAT via the Logix Designer Application (Stratix 5410 Switches) In the navigation pane, click NAT. Table 74 - NAT Fields Field Description Instance Name Displays the unique name of the NAT instance. Port Type Identifies the port type as either uplink or downlink: •...
Page 193 Configure Switch Features Chapter 3 To create a NAT instance, follow these steps. IMPORTANT Configure all Smartport roles and VLANs before creating NAT instances. If you change a Smartport role or the native VLAN for a port that is associated with a NAT instance, you must reassign VLANs to the NAT instance.
Page 194 Chapter 3 Configure Switch Features 2. Configure the ports to assign to the instance. a. In the NAT Instance Name field, type a unique name to identify the instance. b. Click the type of ports to assign to the NAT instance: •Uplink Ports Only (Te1/25…Te1/28) •(Default) Downlink Ports Only (Gi1/1…Gi1/24) c.
Page 195 Configure Switch Features Chapter 3 4. For each port, select one or more VLANs to assign to the NAT instance. The VLANs available for selection are VLANs previously assigned to the port. You can select the same VLAN for multiple ports. VLANs assigned to another NAT instance are unavailable for selection.
Page 196 Chapter 3 Configure Switch Features If you assigned multiple VLANs to the NAT instance, no gateway configuration is necessary. Rockwell Automation Publication 1783-UM007I-EN-P - December 2017...
Page 197 Configure Switch Features Chapter 3 6. Click Next to display the Translations view. Rockwell Automation Publication 1783-UM007I-EN-P - December 2017...
Page 198 Chapter 3 Configure Switch Features 7. Configure translations for one device, a range of devices, or all devices on a subnet. Field Description Device Location Choose the type of network on which the device resides: • Private Network • Public Network Private IP Address Specify a private IP address.
Page 199 Configure Switch Features Chapter 3 Table 75 - Valid Subnet Addresses Subnet Mask Subnet Address 255.255.0.0 The last two octets of the address must end in 0. EXAMPLE: Private address: 192.168.0.0 Public address: 10.200.0.0 255.255.255.0 The last octet of the address must end in 0. EXAMPLE: Private address: 192.168.1.0 Public address: 10.200.1.0...
Page 200: View Address Translations In Linx-Based Software
Chapter 3 Configure Switch Features 9. In the Incoming and Outgoing fields for each type of traffic, choose one of these options: • Pass-Through—Permit unsupported packets to pass across the NAT boundary. • Blocked—Drop unsupported packets. 10. To disable protocol fixups for ARP, clear the Fix up ARP checkbox. 11.
Page 201: Network Time Protocol (Ntp)
Configure Switch Features Chapter 3 Network Time Protocol (NTP) Network Time Protocol (NTP), documented in RFC 1305, is the traditional method of synchronizing clocks across packet-based networks. NTP uses a two-way time transfer mechanism between a master and a slave. NTP is capable of synchronizing devices in a tightly-controlled network.
Page 202 Chapter 3 Configure Switch Features You can add, edit, and delete NTP associations in the table area on the NTP page. You can add multiple NTP servers. To add an association, follow these steps. 1. Click Add. 2. In the IP Address field, specify one of the following: •...
Page 203: Open Shortest Path First (Ospf) Routing Protocol
Displays the relative time of the peer clock to the local clock in milliseconds. Open Shortest Path First OSPF is available on the following switches: • Stratix 5400 with Layer 3 firmware (OSPF) Routing Protocol • Stratix 5410 with Layer 3 firmware •...
Page 204 Chapter 3 Configure Switch Features The OSPF implementation on the switch conforms to the OSPF Version 2 specifications with support for these key features: • Definition of stub areas. • Routes that are learned through any IP routing protocol can be redistributed into another IP routing protocol.
Page 205: Configure Ospf Via Device Manager
Configure Switch Features Chapter 3 OSPF via Device Manager Configure From the Configure menu, choose OSPF. Table 77 - OSPF Fields Field Description OSPF Instances—Add OSPF instances to the OSPF table. To customize the default settings for an instance, see page 208.
Page 206 Chapter 3 Configure Switch Features Table 77 - OSPF Fields (Continued) Field Description Route Summarization—Route summarization consolidates and summarizes addresses for an area and is used only with area border routers (ABRs). In OSPF, an ABR advertises networks in one area into another area. If the network numbers in an area are contiguous, you can configure the ABR to advertise a summary route that covers all individual networks within the area that are in the specified range.
Page 207 Configure Switch Features Chapter 3 Table 77 - OSPF Fields (Continued) Field Description Summary Address—An OSPF ASBR uses a summary address to advertise one external route as an aggregate for all redistributed routes that are covered by the address. OSPF ID Choose an OSPF routing process ID.
Page 208 Chapter 3 Configure Switch Features To change the default settings after adding an EIGRP instance, on the EIGRP Instances tab, click the button in the row to customize, and then click Customize Default Settings. IMPORTANT Setting metrics is complex and is not recommended without guidance from an experienced network designer.
Page 209 Configure Switch Features Chapter 3 Table 78 - Customize OSPF Parameters (Continued) Field Description Flood Pacing Type the time at which LSAs in the flooding queue are paced between updates. Valid values: 5…100 ms Default: 33 ms The default settings for OSPF packet pacing timers are suitable for most OSPF deployments. Do not change the packet pacing timers unless all other options to meet OSPF packet flooding requirements have been exhausted.
Page 210: Parallel Redundancy Protocol (Prp)
Single Attached Node (SAN) Device with a network interface that is connected to one of the two LANs. Redundancy Box (RedBox) Device that connects one or more SANs to both LANs. Stratix 5400 and 5410 switches implement RedBox functionality. Virtual DAN (VDAN) A SAN connected to both LANs through a RedBox.
Page 211 Configure Switch Features Chapter 3 Figure 27 - Parallel Redundancy Protocol (PRP) Topology 1756-EN2TP, PRP Communication Module, Doubly Attached Node (DAN) DC OUTPUT DC INPUT DIAG DIAG LAN A (Blue) LAN B (Green) Stratix Switch Stratix Switch LAN A LAN B LAN A LAN B LAN B...
Page 212 In this example, the Stratix 5400 switch is configured as a RedBox. IMPORTANT You can use only a Stratix 5400 or 5410 switch as a RedBox. However, you can use any switch as an infrastructure switch in a PRP system.
Page 213: Prp Channel Groups
Chapter 3 PRP Channel Groups For RedBox functionality, Stratix 5400 and 5410 switches have designated ports for PRP channel groups. A PRP channel group is a logical interface that aggregates two Gigabit Ethernet physical ports into a single link. In the channel group, the lower numbered Gigabit Ethernet member port is the primary port and connects to LAN A.
Page 214: Configure A Stratix 5400 Or 5410 Switch As A Redbox
Chapter 3 Configure Switch Features To configure Stratix switches for PRP, complete this process. 1. Configure a Stratix 5400 or 5410 as a RedBox as described on page 214. 2. Configure infrastructure switches in LAN A and LAN B as described page 218.
Page 215 Table 81 - Add PRP Channel Fields Field Description Channel Group Number Choose a channel group number: • Stratix 5400 switches provide 1 channel group • Stratix 5410 switches provide 2 channel groups Port 1 Choose a port to be a member of the channel group.
Page 216 Table 82 - Add PRP VDAN Fields Field Description Channel Group Number Choose a channel group number: • Stratix 5400 switches provide 1 channel group • Stratix 5410 switches provide 2 channel groups VDAN MAC Addres Type the MAC ID of the VDAN.
Page 217 Configure Switch Features Chapter 3 5. On each downlink port of the RedBox that connects to an end device, enable PortFast. a. From the Configure menu, choose STP. b. Click the PortFast tab. c. In the Per-Interface Port Fast Table, check Enable Port Fast next to each port that connects to an end device.
Page 218: Configure Infrastructure Switches In Lan A And Lan B
Configure Infrastructure Switches in LAN A and LAN B This procedure applies to Stratix switches acting as infrastructure switches in a PRP system. This procedure does not apply to a Stratix 5400 or 5410 switch configured as a RedBox. To configure infrastructure switches in LAN A and LAN B, follow these steps.
Page 219: Port Mirroring
Configure Switch Features Chapter 3 Port Mirroring Port mirroring is for advanced users with experience in troubleshooting traffic and protocol issues on networks. Port mirroring copies, or mirrors, traffic on one port to a monitoring port where a network protocol analyzer tool can capture the packet.
Page 220: Configure Port Mirroring In Device Manager
Chapter 3 Configure Switch Features Configure Port Mirroring in Device Manager To configure port mirroring, follow these steps. 1. From the Configure menu, choose Smartports. 2. Select the checkbox next to the port to do the monitoring, and then click Edit. 3.
Page 221: Port Security
Configure Switch Features Chapter 3 Port Security Stratix managed switches implement MAC address-based port security. A MAC ID is a unique address that is assigned to each Ethernet-capable device. Switches can enforce communication either dynamically or statically per MAC ID. With dynamic port security, a switch port communicates with some number of devices.
Page 222: Static Secure Mac Id
Chapter 3 Configure Switch Features Static Secure MAC ID The other method of limiting MAC IDs is to configure statically one or more MAC IDs for a port by defining them via port security with Device Manager. These addresses become part of the saved configuration of the switch. This method provides strong security.
Page 223: Configure Port Security Via Device Manager
Configure Switch Features Chapter 3 Configure Port Security via Device Manager From the Configure menu, choose Port Security. Port security limits and identifies the MAC IDs of devices that can send traffic through the switch port. The switch port does not forward traffic from devices outside the defined group of devices.
Page 224 Chapter 3 Configure Switch Features To change the static MAC IDs table for a port, follow these steps. 1. Click the radio button next to the port to configure. 2. Click Edit. 3. Clear or check the Enable checkbox. 4. Configure MAC IDs as follows: •...
Page 225: Configure Port Security Via The Logix Designer Application
Configure Switch Features Chapter 3 Configure Port Security via the Logix Designer Application In the navigation pane, click Port Security. For Stratix 8000/8300 switches, use Advanced Port Configuration as described on page 226. Figure 29 - Port Security Table 85 - Port Security Fields Field Description Port...
Page 226 Chapter 3 Configure Switch Features For Stratix 8000/8300 switches, in the navigation pane, click Advanced Port Configuration. Figure 30 - Advanced Port Configuration for Stratix 8000/8300 Switches Table 86 - Advanced Port Configuration Fields for Stratix 8000/8300 Switches Field Description Unit Indicates where the port resides: •...
Page 227: Port Thresholds
Configure Switch Features Chapter 3 Port Thresholds Port thresholds help prevent traffic on a LAN from being disrupted by a broadcast, multicast, or unicast storm on one of the physical interfaces. Port thresholds do not apply to switches with lite firmware. A LAN storm occurs when packets flood the LAN, creating excessive traffic and degrading network performance.
Page 228: Outgoing (Rate Limiting)
Chapter 3 Configure Switch Features Figure 31 - Port Thresholds Example Forwarded Traffic Blocked Traffic Total Number of Broadcast Threshold Packets or Bytes Time The combination of the storm-control suppression level and the 1-second time interval controls the way the port thresholds algorithm works. A higher threshold enables more packets to pass through.
Page 229: Configure Port Thresholds Via Device Manager
Configure Switch Features Chapter 3 Configure Port Thresholds via Device Manager From the Configure menu, choose Port Thresholds. Table 87 - Port Threshold Fields Field Description Incoming Unicast For each port, do the following: 1. Check or clear the Enable checkbox. Multicast 2.
Page 230: Configure Port Thresholds Via The Logix Designer Application
Figure 32 - Port Thresholds for Stratix 5400, Stratix 5410, Stratix 5700, and ArmorStratix 5700 Switches Table 88 - Port Threshold Fields for Stratix 5400, Stratix 5410, Stratix 5700, and ArmorStratix 5700 Switches Field...
Page 231 Configure Switch Features Chapter 3 Figure 33 - Port Thresholds for Stratix 8000/8300 Switches Table 89 - Port Threshold Fields for Stratix 8000/8300 Switches Field Description Unit Indicates where the port resides: • Base (for example, 1783-MS10T) • Expansion module (for example, 1783-MX08T) Port Indicates the port that is selected for configuration.
Page 232: Power Over Ethernet (Poe)
Chapter 3 Configure Switch Features Power over Ethernet (PoE) Switches and expansion modules with PoE ports are software-configurable and provide these features: • Support for IEEE 802.3af (PoE)-compliant devices. • Support for IEEE 802.3at Type 2 (PoE+), which increases the available power that can be drawn by powered devices from 15.4…30 W per port.
Page 233: Powered Device Detection And Initial Power Allocation
Configure Switch Features Chapter 3 Configuration options include the following: • Limit the total power supported. • Configure mode and power settings for individual ports. For most applications, the default configuration (Auto mode) is sufficient and no further configuration is required. However, you can customize the settings to meet your needs.
Page 234: Power Management Modes
Chapter 3 Configure Switch Features • A Cisco pre-standard powered device does not provide its power requirement when the switch detects it. A port that is not configured for PoE+ allocates 15.4 W as the initial allocation for power budgeting. A port that is configured for a PoE+ switch allocates 30 W.
Page 235 Configure Switch Features Chapter 3 If enough power is available for all powered devices that are connected to the switch, power is turned on to all devices. If there is not enough power to accommodate all connected devices and if a device is reconnected while other devices are waiting for power, it cannot be determined which devices are granted or are denied power.
Page 236 Chapter 3 Configure Switch Features Maximum Power Allocation (Cutoff Power) on a PoE Port The switch determines the cutoff power on a PoE port in this order. 1. Manually when you configure the power level to budge for the port 2.
Page 237: Configure Poe Ports Via Device Manager
Configure Switch Features Chapter 3 Because the switch supports external removable power supplies for PoE/PoE+ and can configure the budget per the power supply that is used, the total amount of power available varies depending on the power supply configuration: •...
Page 238 Chapter 3 Configure Switch Features Figure 35 - PoE Configuration for Stratix 5400, Stratix 5700, and ArmorStratix 5700 Switches Figure 36 - PoE Configuration for Stratix 8000/8300 Switches Table 91 - Power Management Fields Field Description Selected Module Choose a connected PoE module for which to view status information: (Stratix 8000/8300 switches) •...
Page 239 Configure Switch Features Chapter 3 Table 91 - Power Management Fields (Continued) Field Description Mode Displays the Power Management mode of the port: • Auto—(Default) Enables the detection of powered devices and automatically allocates power to the PoE port if a device is connected. To limit the power that is used by this port, adjust the Max Power setting.
Page 240: Configure Poe Via The Logix Designer Application
Chapter 3 Configure Switch Features Configure PoE via the Logix Designer Application In the navigation pane, click PoE. Figure 37 - PoE Configuration for Stratix 5410 Switches Rockwell Automation Publication 1783-UM007I-EN-P - December 2017...
Page 241 Configure Switch Features Chapter 3 Figure 38 - PoE Configuration for Stratix 5400, Stratix 5700, and ArmorStratix 5700 Switches Figure 39 - PoE Configuration for Stratix 8000/8300 Switches Rockwell Automation Publication 1783-UM007I-EN-P - December 2017...
Page 242 Chapter 3 Configure Switch Features Table 92 - PoE Fields Field Description Power over Ethernet (PoE) Port Configuration Port Displays the port number. Mode Displays the Power Management mode of the port: • Auto—Enables the detection of powered devices and automatically allocates power to the PoE port if a device is connected. This setting is selected by default.
Page 243: Profinet
Configure Switch Features Chapter 3 PROFINET PROFINET is the PROFIBUS International (PI) open Industrial Ethernet Standard that uses TCP/IP and IT standards for automation control. Stratix switches support the following PROFINET features: • All switches support the forwarding of these PROFINET traffic types: –...
Page 244 Chapter 3 Configure Switch Features To configure VLAN 0 priority tagging to support PROFINET in IOS 15.2(5)EA.fc4 and earlier, follow these steps. 1. Start a CLI session. For more information about using the CLI, see page 2. At the prompt, connect to the switch by entering the switch user name and password.
Page 245: Configure A Stratix 5700 Or Armorstratix 5700 Switch For Profinet Management
Configure Switch Features Chapter 3 Configure a Stratix 5700 or ArmorStratix 5700 Switch for PROFINET Management Stratix 5700 and ArmorStratix 5700 switches contain a PROFINET GSD (General Station Description) file that contains basic information about the switch for data exchange between the I/O controller, the I/O supervisor, and the I/O devices, including the switch.
Page 246 Chapter 3 Configure Switch Features To configure a Stratix 5700 or ArmorStratix 5700 switch for PROFINET management, use this process. By default, PROFINET is disabled. 1. Download the GSD file from the switch. a. In the IOS folder on the switch, locate the Rockwell_S5700_GSD.zip file.
Page 247 Configure Switch Features Chapter 3 Table 95 - CLI Commands to Enable PROFINET Command Description Step 1 profinet Enables PROFINET on the switch. Step 2 profinet id [PROFINET device name] Sets the PROFINET device identifier (ID). IMPORTANT: This ID must match the PROFINET device name you specified for the switch in your controller project. The maximum length is 240 characters.
Page 248: Verify The Gsd File
Chapter 3 Configure Switch Features Verify the GSD File To verify that the GSD file for the switch matches the GSD file in the controller configuration software, do the following. 1. Establish a connection between the switch and the I/O controller. 2.
Page 249: Resilient Ethernet Protocol (Rep)
Configure Switch Features Chapter 3 Resilient Ethernet Protocol REP provides an alternative to Spanning Tree Protocol (STP) to control network rings and loops, handle link failures, and improve convergence time. (REP) REP controls a group of ports that are connected in a segment, makes sure that the segment does not create any bridging loops, and responds to link failures within the segment.
Page 250: Rep Open Segment
Chapter 3 Configure Switch Features REP and STP can coexist on the same switch, but not on the same port. REP does not interact with STP. For example, if a port is configured as an REP port, STP is disabled on that port. STP bridge protocol data units (BPDUs) are not accepted on or sent from REP ports.
Page 251: Rep Ring Segment
Configure Switch Features Chapter 3 REP Ring Segment The segment that is shown in Figure 41, with both edge ports on the same switch, is a ring segment. In this configuration, there is connectivity between the edge ports through the segment. With this configuration, you can create a redundant connection between any two switches in the segment.
Page 252: Link Integrity
Chapter 3 Configure Switch Features In the example that is shown in Figure 42, E1 or E2 can be configured as the primary no-neighbor port. Figure 42 - Ring Topology Example REP Not Supported REP Ports Configured at Transit Ports REP has these limitations: •...
Page 253: Configure Rep Via Device Manager
Configure Switch Features Chapter 3 Configure REP via Device Manager From the Configure menu, choose REP. To create a REP segment, set a segment ID and port type for a switch port. Table 96 - REP Fields Field Description REP Admin VLAN The administrative VLAN.
Page 254: Routing, Layer 3
By default, the checkbox is cleared. Routing, Layer 3 Layer 3 routing is available on the following switches: • Stratix 5400 with Layer 3 firmware • Stratix 5410 with Layer 3 firmware • Stratix 8300 base units Layer 3 routing uses IP address information to map subnetworks to an individual VLAN.
Page 255 Configure Switch Features Chapter 3 Stratix switches that support Layer 3 routing can route packets by using these methods. Table 97 - Routing Methods Feature Description EIGRP Enhanced Interior Gateway Routing Protocol (EIGRP) on page 136. OSPF Open Shortest Path First (OSPF) Routing Protocol on page 203.
Page 256: Routing, Static And Connected
Chapter 3 Configure Switch Features Routing, Static and Static and connected routing is available on the following switches: • Stratix 5400 Connected • Stratix 5410 • Stratix 5700 switches with Full firmware • ArmorStratix 5700 • Stratix 8000 and 8300 Static routing defines explicit paths between two devices (routers and switches).
Page 257: Reallocate Switch Memory For Routing Via Device Manager
Configure Switch Features Chapter 3 Reallocate Switch Memory for Routing via Device Manager Switch Management Database (SDM) templates optimize how switch memory is allocated for specific features, such as routing. To enable routing, you must change the default SDM template to the Lanbase Routing template. To apply an SDM template, follow these steps.
Page 258: Enable And Configure Routing Via Device Manager
Chapter 3 Configure Switch Features Enable and Configure Routing via Device Manager Before you can enable routing, you must reallocate switch memory for routing as described on page 257. From the Configure menu, choose Routing. From the Routing page, you can enable connected routing only or both static and connected routing.
Page 259: Simple Network Management Protocol (Snmp)
Configure Switch Features Chapter 3 Simple Network The switch supports SNMP versions 1, 2C, and 3. SNMP enables the switch to be remotely managed through other network management software. This Management Protocol feature is disabled by default. (SNMP) SNMP is based on three concepts: •...
Page 260: Supported Mibs
Chapter 3 Configure Switch Features Supported MIBs Stratix managed switches support the following MIBs. Table 98 - Supported MIBs MIB Name BRIDGE-MIB CISCO-MAC-NOTIFICATION-MI IP-FORWARD-MIB CALISTA-DPA-MIB CISCO-MEMORY-POOL-MIB IP-MIB CISCO-ACCESS-ENVMON-MIB CISCO-PAE-MIB LLDP-EXT-MED-MIB CISCO-ADMISSION-POLICY-MIB CISCO-PAGP-MIB LLDP-MIB CISCO-AUTH-FRAMEWORK-MIB CISCO-PING-MIB NETRANGER CISCO-BRIDGE-EXT-MIB CISCO-PORT-QOS-MIB NOTIFICATION-LOG-MIB CISCO-BULK-FILE-MIB CISCO-PORT-SECURITY-MIB OLD-CISCO-CHASSIS-MIB CISCO-CABLE-DIAG-MIB...
Page 261: Configure Snmp Via Device Manager
Configure Switch Features Chapter 3 Configure SNMP via Device Manager From the Configure menu, choose SNMP. Community strings are passwords to the switch Management Information Base (MIB). You can create community strings that provide a remote manager read-only or read-write access to the switch. To create, modify, and delete, click the Community Strings tab.
Page 262: Use Snmp Management Applications
Chapter 3 Configure Switch Features Use SNMP Management Applications You can use SNMP management applications such as IntraVue or HP OpenView to configure and manage the switch. Refer to Simple Network Management Protocol (SNMP) on page 259 for more information. Smartports are recommended configurations for switch ports.
Page 263: Custom Smartport Roles
Configure Switch Features Chapter 3 Table 99 - Smartport Roles (Continued) Port Role Description Virtual Desktop for Automation Apply this role to ports connected to computer running virtualization software. This can be used with devices running up to two MAC IDs: •...
Page 264: Configure Smartports Via Device Manager
Chapter 3 Configure Switch Features Configure Smartports via Device Manager IMPORTANT When you change the Smartport role for a port, the switch sets the VLAN assigned to the port back to the default VLAN 1. You must reassign VLANs to a port after changing its Smartport role.
Page 265 Configure Switch Features Chapter 3 4. Modify the VLAN assignments and click OK. Rockwell Automation Publication 1783-UM007I-EN-P - December 2017...
Page 266 Chapter 3 Configure Switch Features Manage Custom Smartport Macros Custom Smartports macros are not available on Stratix 8000/8300 switches. 1. Click the Custom Smartports tab. 2. Click Add. 3. Enter the name for the macro. Macro names are case-sensitive. The string can be up to 31 alphanumeric characters.
Page 267 Configure Switch Features Chapter 3 Modify the Definition of a Custom Smartports Macro You cannot modify a custom Smartports macro that is currently in use. 1. From the Configure menu, choose Smartports. 2. Click the Custom Smartports tab. 3. Check the checkbox next to the macro to modify. 4.
Page 268 Chapter 3 Configure Switch Features Delete a Custom Smartports Macro You cannot delete a custom Smartports macro that is currently in use. 1. From the Configure menu, choose Smartports. 2. Click the Custom Smartports tab. 3. Check the checkbox next to the macro to delete. 4.
Page 269 Configure Switch Features Chapter 3 5. Select the macro file on your computer or network drive. The file must be an appropriately formatted .xml file. 6. Click Import Macros. 7. Click OK. Export a Custom Smartports Macro 1. From the Configure menu, choose Smartports. 2.
Page 270: Assign Smartports And Vlans Via The Logix Designer Application
Chapter 3 Configure Switch Features Assign Smartports and VLANs via the Logix Designer Application In the navigation pane, click Smartports & VLANs. For Stratix 8000/8300 switches, use Advanced Port Configuration as described on page 271. Figure 44 - Smartport & VLAN Assignment Rockwell Automation Publication 1783-UM007I-EN-P - December 2017...
Page 271 Configure Switch Features Chapter 3 For Stratix 8000/8300 switches, in the navigation pane, click Advanced Port Configuration. Figure 45 - Advanced Port Configuration for Stratix 8000/8300 Switches Table 100 - Smartport and VLAN Assignment Fields Field Description Unit Indicates where the port resides: •...
Page 272: Spanning Tree Protocol (Stp)
Chapter 3 Configure Switch Features Spanning Tree Protocol (STP) STP, the IEEE 802.1D bridge protocol, is a Layer 2 link management protocol that provides path redundancy and helps to prevent loops in the network. The switch supports the following STP versions: •...
Page 273: Configure Stp Via Device Manager
Configure Switch Features Chapter 3 We recommend that you leave STP enabled to help prevent network loops and provide a redundant path if the active path becomes unavailable. IMPORTANT Disabling STP can affect connectivity to the network. Configure STP via Device Manager From the Configure menu, choose STP Settings.
Page 274 Chapter 3 Configure Switch Features For PVST+ or Rapid PVST+ modes, you can enable or disable STP on each VLAN. PortFast Settings On the PortFast tab, you can change the way that STP is implemented on individual ports. PortFast features are typically enabled only on access ports. Access ports connect to devices such as personal computers, access points, and servers that are not expected to send bridge protocol data units (BPDUs).
Page 275 Configure Switch Features Chapter 3 BPDU Features Switches exchange special frames that are called BPDUs to communicate network information, to track changes, and to create the STP topology. Because transmitted BPDUs reveal network information and received BPDUs can influence your STP topology, consider enabling BPDU Filtering and BPDU Guard on your access ports.
Page 276: Configure Stp Via The Logix Designer Application
In the Administration area, you can choose an STP mode. MST/RSTP is the default mode. For more information about each mode, see page 272. Figure 46 - Switch Configuration for Stratix 5400, Stratix 5410, Stratix 5700, and ArmorStratix 5700 Switches Rockwell Automation Publication 1783-UM007I-EN-P - December 2017...
Page 277: Virtual Local Area Networks (Vlans)
Configure Switch Features Chapter 3 Virtual Local Area Networks A VLAN is a logical segment of the network that isolates traffic types and helps prevent collisions among data packets. Isolating different types of traffic (VLANs) helps to preserve the quality of the transmission and to minimize excess traffic among the logical segments.
Page 278: Management Vlan
Configure VLANs via the Logix Designer Application VLAN configuration via the Logix Designer application is available for only Stratix 5400, Stratix 5410, Stratix 5700, and ArmorStratix 5700 switches. In the navigation pane, click Smarports & VLANs. In the VLAN Configuration area, you can add, edit, and delete VLANs.
Page 279 Configure Switch Features Chapter 3 Figure 47 - VLAN Configuration for Stratix 5400, Stratix 5410, Stratix 5700, and ArmorStratix 5700 Switches To assign ports to VLANs, see Assign Smartports and VLANs via the Logix Designer Application on page 270. Rockwell Automation Publication 1783-UM007I-EN-P - December 2017...
Page 280: Vlan 0 Priority Tagging
Chapter 3 Configure Switch Features VLAN 0 Priority Tagging VLAN 0 priority tagging enables 802.1Q Ethernet frames to be transmitted with the VLAN ID set to zero. For example, you can use this feature to forward PROFINET traffic through the switch. These frames are called priority tagged frames.
Page 281: Vlan 0 Priority Tagging And Priority Values
Configure Switch Features Chapter 3 VLAN 0 Priority Tagging and Priority Values When VLAN 0 priority tagging is configured on the interface, the 802.1P priority bits are retained on ingress for the VLAN 0 tagged Ethernet frames. To retain the 802.1P priority bits of the VLAN 0 Ethernet packets on egress, the egress interface must be in trunk mode, and the native VLAN should not be the same native VLAN as the ingress interface.
Page 282: Rockwell Automation Publication 1783-Um007I-En-P - December
Chapter 3 Configure Switch Features Notes: Rockwell Automation Publication 1783-UM007I-EN-P - December 2017...
Page 283: Monitor The Switch
Chapter Monitor the Switch Topic Page Switch Status via Device Manager Switch Status via the Logix Designer Application System Log Messages Trends Port Statistics NAT Statistics REP Status CIP Status DHCP Clients DLR Status PRP Status STP Status STP Status Cable Diagnostics Rockwell Automation Publication 1783-UM007I-EN-P - December 2017...
Page 284: Switch Status Via Device Manager
Chapter 4 Monitor the Switch Switch Status via The Dashboard page in Device Manager lets you monitor switch status and performance. Device Manager The Dashboard page is similar to the Monitor > Trends page. The Dashboard page displays the instantaneous status while the Trends page displays the historical status.
Page 285: Front Panel
Monitor the Switch Chapter 4 Front Panel The Front Panel view on the dashboard is a graphical display of the switch front panel, with color-coded switch components that indicate status. The status indicators on the view in Device Manager match the status indicators on the physical switch: •...
Page 286 Chapter 4 Monitor the Switch You can identify the physical switch in the group of similar devices by checking the Locate Switch checkbox on the Front Panel view. Figure 51 - Locate Switch Checkbox When you check the Locate Switch checkbox, the system status indicators on the physical switch (Setup, EIP NET, EIP Mod, Alarm) flash green to indicate that the feature is enabled.
Page 287 Monitor the Switch Chapter 4 Table 101 - Stratix 5700 and ArmorStratix 5700 System Status Indicators Indicator Status Description Setup The Setup status indicator shows the status of the initial setup of the switch. The behavior of the Setup status indicator varies depending on whether you run single-mode or multi-mode Express Setup. In multi-mode Express Setup, the behavior varies based on whether you run Short Press, Medium Press, or Long Press mode.
Page 288 Chapter 4 Monitor the Switch Table 102 - Stratix 5700 and ArmorStratix 5700 Port Status Indicators Mode Status Description Status In Status mode, the port status indicators show the connection and activity status of the port. Status mode is the default mode. No link is present on the port.
Page 289 Chapter 4 Stratix 5400 Front Panel Along with the View modes on the Dashboard page, the Stratix 5400 switch has a Display Mode button on the physical switch. The Display Mode button changes the behavior of the port status indicators. Select a mode by pressing the Display Mode button on the physical switch.
Page 290 Chapter 4 Monitor the Switch Table 103 - Stratix 5400 System Status Indicators Indicator Status Description Setup The Setup status indicator shows the status of the initial setup of the switch.The Setup status indicator shows the status of the initial setup of the switch.
Page 291 Monitor the Switch Chapter 4 Table 104 - Stratix 5400 Port Status Indicators Mode Status Description Status In Status mode, the port status indicators show the connection and activity status of the port. Status mode is the default mode. You can choose Status mode via the View pull-down menu in Device Manager.
Page 292 Chapter 4 Monitor the Switch Stratix 5410 Front Panel In addition to the View modes on the Dashboard page, the Stratix 5410 switch has a Disp. Mode button on the physical switch that changes the behavior of the port status indicators based on the selected mode. Select a mode by pressing the Disp.
Page 293 Monitor the Switch Chapter 4 Table 105 - Stratix 5410 System Status Indicators Indicator Status Description EIP Mod The EIP Mod status indicator shows the status of the switch. Power to the switch is off or is not properly connected. Solid green The switch is operating properly.
Page 294 Chapter 4 Monitor the Switch Table 105 - Stratix 5410 System Status Indicators (Continued) Indicator Status Description Power is not present on the circuit, or the system is not powered up. Solid green Power output is good. Flashing red Power supply is installed, but power input is bad. Solid red Power output is bad.
Page 295 Monitor the Switch Chapter 4 Stratix 8000/8300 Front Panel Table 107 - Stratix 8000/8300 System Status Indicators Indicator Status Description EIP Mod The EIP Mod status indicator shows the status of the switch. Power to the switch is off or is not properly connected. Solid green The switch is operating properly.
Page 296: Switch Information
Chapter 4 Monitor the Switch Table 108 - Stratix 8000/8300 Port Status Indicators Mode Status Description Status In Status mode, the port status indicators show the status of the ports. Status is the default mode. No link Solid green No activity on link. Flashing green Link activity.
Page 297: Switch Health
Monitor the Switch Chapter 4 Switch Health You can use the health gauges to monitor CPU utilization and temperature. The CPU Utilization gauge shows the percentage of CPU processing power that is in use on the switch. Data is collected at each 60-second system refresh. The gauge changes as the switch experiences the network activity from devices sending data through the network.
Page 298: Port Utilization
Chapter 4 Monitor the Switch Port Utilization You can choose which types of network traffic to display and in what format: • Types of traffic—By default, all traffic is displayed for all interfaces. Click the links above the display area to display all traffic, errors, received traffic, or transmitted traffic.
Page 299: Switch Status Via The Logix Designer Application
Monitor the Switch Chapter 4 Switch Status via the Logix The Switch Status view in the Studio 5000 Logix Designer® application lets you view status parameters for the switch. Designer Application In the navigation pane, click Switch Status. Table 110 - Switch Status Fields Field Description Alarms &...
Page 300 Chapter 4 Monitor the Switch Table 110 - Switch Status Fields (Continued) Field Description SD Card Present Displays whether the SD card is installed. Power Power Present on Terminal A Displays Yes or No to indicate whether power is present on Terminal A. Power Present on Terminal B Displays Yes or No to indicate whether power is present on Terminal B.
Page 301 Monitor the Switch Chapter 4 You can also monitor the switch status on the Module Info view. Table 111 - Module Info Fields Field Description Identification Displays the following switch information: • Vendor • Product type • Product code • Revision •...
Page 302: Port Status
Chapter 4 Monitor the Switch Port Status In the navigation pane, click Port Status. You can monitor alarms, statuses, thresholds, and bandwidth utilization for each switch port. You can also access port and cable diagnostics. Table 112 - Port Status Fields Field Description Unit...
Page 303: System Log Messages
Monitor the Switch Chapter 4 Table 112 - Port Status Fields (Continued) Field Description Threshold Exceeded Displays unusual changes for these types of network traffic: • Unicast—Displays Yes or No to indicate whether the current unicast traffic has exceeded the threshold value. •...
Page 304: Trends
Chapter 4 Monitor the Switch To filter historical events, choose a severity filter or type filter: • Debugging—Debug messages. • Informational—Informational messages. • Notifications—The switch is operating normally but has a significant condition. • Warnings—The switch has a warning condition. •...
Page 305 Monitor the Switch Chapter 4 Table 114 - Trends Graphs Graph Description Bandwidth Utilization The Bandwidth Utilization graph indicates the percentage of the available bandwidth that was used. The graph can show the bandwidth usage patterns over incremental instances in time (by 60 seconds, 60 minutes, 24 hours, or 14 days). This graph also marks the highest peak reached. The default is 60 seconds.
Page 306: Port Statistics
Chapter 4 Monitor the Switch Port Statistics In Device Manager, you can view statistics for data that passes through the switch ports. If you use Parallel Redundancy Protocol (PRP), ports that belong to a PRP channel configured on a RedBox are marked with an asterisk (*). For more information about configuring PRP channels, see page 214.
Page 307: Nat Statistics
• Statistics per instance • Detailed private translations per instance • Detailed public translations per instance From the Monitor menu, choose NAT Statistics. Figure 54 - NAT Statistics for Stratix 5400 and 5700 Switches Rockwell Automation Publication 1783-UM007I-EN-P - December 2017...
Page 308 Figure 55 - NAT Statistics for Stratix 5410 Table 116 - NAT Statistics Field Description Global Statistic s for Stratix 5400 and 5700 Switches Current Active Translations The number of IP addresses that have been translated within the last 90 seconds across all NAT instances. Total Translations The total number of translations across all NAT instances.
Page 309 Monitor the Switch Chapter 4 Table 116 - NAT Statistics (Continued) Field Description Total Translations Attached to Core 0 The total number of translations across all NAT instances for ports 1…6 and 13…18. Total Instances Attached to Core 0 The total number of NAT instances across ports 1…6 and 13…18. Total Translations Attached to Core 1 The total number translations across all NAT instances for ports 7…12, 19…24, and 25…28.
Page 310: Monitor Nat Statistics Via The Logix Designer Application
Chapter 4 Monitor the Switch Monitor NAT Statistics via the Logix Designer Application For each NAT instance, you can monitor these diagnostics: • Diagnostics for both private and public translations • Diagnostics for only private translations • Diagnostics for only public translations In the navigation pane, click NAT, and then click the ellipse in the Diagnostics column.
Page 311 Monitor the Switch Chapter 4 Table 117 - NAT Diagnostics per Instance Field Description Current Active Translations Displays the number of translations that have occurred within the last 90 seconds across all NAT instances. Total NAT Translated Packets Displays the total number of packets that have been translated for this instance. Total Private to Public Address Translations Displays the total number of private-to-public translations for this instance.
Page 312 Chapter 4 Monitor the Switch From the Public to Private Translations dialog box for an instance, you can view a list of IP addresses that have been changed by NAT within the last 90 seconds. Table 119 - Public-to-Private Translation Diagnostics Field Description Public...
Page 313: Rep Status
Monitor the Switch Chapter 4 REP Status In Device Manager, you can review the status of the REP topology for one or all network segments. From the Monitor menu, choose REP. To display an archived REP topology, click the Archived Topology tab and then select the segment ID.
Page 314 Chapter 4 Monitor the Switch From the Monitor menu, choose CIP Status. Table 120 - CIP Status Fields Field Description Overview State The state of the CIP connection (Enabled or Disabled). VLAN The VLAN ID. CIP I/O Connection Owner The IP address of the device to and from which application-specific I/O output data is sent and received. CIP Config Session Owner The IP address of the device controlling the CIP configuration session.
Page 315: Dhcp Clients
Monitor the Switch Chapter 4 DHCP Clients In Device Manager, you can view information about devices connected to a switch with DHCP snooping enabled. These devices are known as DHCP clients. The DHCP snooping feature dynamically builds and maintains entries in the DHCP Clients table shown below.
Page 316: Dlr Status
Logix Designer application. Configuration parameters appear for the number of available rings: • Stratix 5700 and ArmorStratix™ 5700 switches show one ring. • Stratix 5400 switches show three rings. For more information about DLR troubleshooting, see Troubleshoot EtherNet/IP Networks, publication ENET-AT003.
Page 317 Monitor the Switch Chapter 4 Rockwell Automation Publication 1783-UM007I-EN-P - December 2017...
Page 318: Monitor Dlr Status Via The Logix Designer Application
Chapter 4 Monitor the Switch Monitor DLR Status via the Logix Designer Application From the navigation pane, expand Device Level Ring (DLR), expand Ring 1, Ring 2, or Ring 3, and then click one of the following: • To view the status and parameters that are configured for the switch, the redundant gateway, and the active ring supervisor, click Statistics.
Page 319 Monitor the Switch Chapter 4 Rockwell Automation Publication 1783-UM007I-EN-P - December 2017...
Page 320: Prp Status
For more information about PRP, see the following: • Parallel Redundancy Protocol (PRP) on page 210. • Stratix 5400 Display Modes on page 289 • Stratix 5410 Display Modes on page 292 From the Monitor menu, choose PRP. Table 122 - VDAN Table Fields...
Page 321 Monitor the Switch Chapter 4 Table 123 - Node Table Fields Field Description Channel Group 1, 2 The number of the PRP channel group. MAC Count The number of static and dynamic MAC IDs for the channel group. The number of dual attached node (DAN) MAC IDs for the channel group. SAN-A The number of single attached nodes (SANs) on LAN A.
Page 322: Stp Status
Chapter 4 Monitor the Switch STP Status In Device Manager, you can view spanning tree information for Multiple Spanning Tree (MST) or Rapid Spanning Tree Protocol (RSTP). From the Monitor menu, choose STP. On the RSTP tab, choose a VLAN ID to monitor and click Submit. Table 124 - RSTP Tab Fields Field Description...
Page 323 Monitor the Switch Chapter 4 Table 124 - RSTP Tab Fields (Continued) Field Description Role Current 802.1w role: • Boun—Boundary • Desg—Designated • Root • Altn—Alternate • Back—Backup Spanning-tree states: • BLK—Blocked: The port is still sending and listening to BPDU packets but is not forwarding traffic. •...
Page 324: Port Diagnostics
Chapter 4 Monitor the Switch Table 125 - MST Tab Fields Field Description Vlans Mapped The VLANs mapped to the selected instance. Root Priority The priority indicator. Address The MAC ID of the port. Cost The root path cost. Port The root port ID.
Page 325 Monitor the Switch Chapter 4 Rockwell Automation Publication 1783-UM007I-EN-P - December 2017...
Page 326 Chapter 4 Monitor the Switch Table 126 - Port Diagnostics Fields Field Description Unit Indicates where the port resides: • Base (for example, 1783-MS10T). (Stratix 8000/8300 switches) • Expansion module (for example, 1783-MX08T). Port The port that is selected for configuration. The port number includes the port type (Fa for Fast Ethernet and Gi for Gigabit Ethernet), the base or expansion module for Stratix 8000/8300 switches, and the specific port number.
Page 327: Cable Diagnostics
Monitor the Switch Chapter 4 Cable Diagnostics The Cable Diagnostics feature lets you run a test on each switch port to determine the integrity of the cable that is connected to the RJ45 (copper) ports. The test determines the distance to the break from the switch for each cable with a plus or minus error value individually listed.
Page 328: Diagnose Cables Via The Logix Designer Application
Chapter 4 Monitor the Switch Diagnose Cables via the Logix Designer Application In the navigation pane, click Port Status, and then click the button in the Cable Diagnostics column for the corresponding port. Table 127 - Cable Diagnostics Fields Field Description Port The port that is selected for configuration.
Page 329: Troubleshoot The Switch
Chapter Troubleshoot the Switch Topic Page Troubleshoot the Installation Verify Boot Fast Troubleshoot IP Addresses Troubleshoot Device Manager Troubleshoot Switch Performance Restart or Reset the Switch Troubleshoot a Firmware Update Collect System and Configuration Information for Technical Support This chapter helps you resolve issues that are related to Stratix® switches and perform common functions, such as reset the switch.
Page 330: Troubleshoot The Installation
Chapter 5 Troubleshoot the Switch Troubleshoot the Installation The status indicators on the front panel provide troubleshooting information about the switch. They show power-on self-test (POST) failures, port connectivity problems, and overall switch performance. You can also get statistics from the browser interface, the command-line interface (CLI), or a Simple Network Management Protocol (SNMP) workstation.
Page 331: Bad Or Damaged Cable
Troubleshoot the Switch Chapter 5 Bad or Damaged Cable Always make sure that the cable does not have marginal damage or failure. Even if a cable can connect at the physical layer, subtle damage to the wiring or connectors can corrupt packets. This situation is likely when the port has many packet errors or the port constantly loses and regains the link.
Page 332: Link Status
Chapter 5 Troubleshoot the Switch Link Status Verify that both sides have a network link. A broken wire or one shut down port can cause one side to show a link, but not the other side. A Link status indicator does not indicate that the cable is fully functional. The cable can encounter physical stress that causes it to function at a marginal level.
Page 333: Verify Boot Fast
Troubleshoot the Switch Chapter 5 Verify Boot Fast Boot Fast failures are potentially fatal to the switch. Contact your Rockwell Automation representative if your switch does not successfully complete Boot Fast. You can disable Boot Fast and run a power-on self-test (POST) by using the CLI.
Page 334: Troubleshoot Switch Performance
Chapter 5 Troubleshoot the Switch Troubleshoot Switch The following table includes basic troubleshooting for issues that are related to switch performance. Performance Issue Resolution Speed, duplex, and autonegotiation Port statistics that show a large amount of alignment errors, frame check sequence (FCS), or late-collisions errors can indicate a speed or duplex mismatch.
Page 335: Restart Or Reset The Switch
Troubleshoot the Switch Chapter 5 Restart or Reset the Switch If you cannot solve an issue by reconfiguring a feature, you can restart or reset the switch to solve the issue. If the issue exists after you reset the switch to its default settings, it is unlikely that the switch is causing the issue.
Page 336: Reset The Switch Via The Express Setup Button
16…20, and then release. See also Run Multi-mode Express Setup in Long Press Mode on page 15.2(4)EA or earlier Stratix 5400, 5410, 5700, Follow these steps. or ArmorStratix™ 5700 1. Make sure that the switch is fully powered up. 2. Press and hold the Express Setup button for 10 seconds until the EIP Mod status indicator turns red, and then immediately release the Express Setup button.
Page 337: Collect System And Configuration Information For Technical Support
Troubleshoot the Switch Chapter 5 Collect System and The Device Manager online Help provides a link that you can use to collect system and configuration information about the switch. When you click the Configuration Information link, the switch runs the show tech-support command via the command-line for Technical Support interface (CLI).
Page 338 Chapter 5 Troubleshoot the Switch Notes: Rockwell Automation Publication 1783-UM007I-EN-P - December 2017...
Page 339 Appendix Data Types Topic Page Stratix 5400 Data Types Stratix 5410 Data Types Stratix 5700 and ArmorStratix 5700 Data Types Stratix 8000 and 8300 Data Types In the Studio 5000 Logix Designer® application, predefined tags for Input and Output data types have a structure that corresponds to the switch selected when it was added to the I/O tree.
Page 340: Stratix 5400 Data Types
Appendix A Data Types Stratix 5400 Data Types The following tables list module-defined data types for Stratix® 5400 switches. The tables include information for input (I) and output (O). 8-port Switches Catalog number 1783-HMS4C4CGN Table 129 - Input Data Types (8-port switches)
Page 341 Data Types Appendix A Table 129 - Input Data Types (8-port switches) (Continued) AB:STRATIX_5400_8PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortGi1_3Utilization SINT Decimal PortGi1_4Utilization SINT Decimal PortFa1_5Utilization SINT Decimal PortFa1_6Utilization SINT Decimal PortFa1_7Utilization SINT Decimal PortFa1_8Utilization SINT Decimal MajorAlarmRelay BOOL Decimal...
Page 342: 12-Port Switches
Appendix A Data Types 12-port Switches Catalog numbers 1783-HMS8T4CGN,1783-HMS8S4CGN, 1783-HMS4T4E4CGN Table 131 - Input Data Types (12-port switches) AB:STRATIX_5400_12PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style Fault DINT Binary AnyPortConnected BOOL Decimal LinkStatus:0 PortGi1_1Connected BOOL Decimal LinkStatus:1 PortGi1_2Connected BOOL Decimal LinkStatus:2 PortGi1_3Connected...
Page 343 Data Types Appendix A Table 131 - Input Data Types (12-port switches) (Continued) AB:STRATIX_5400_12PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortFa1_7Threshold BOOL Decimal ThresholdExceeded:7 PortFa1_8Threshold BOOL Decimal ThresholdExceeded:8 PortFa1_9Threshold BOOL Decimal ThresholdExceeded:9 PortFa1_10Threshold BOOL Decimal ThresholdExceeded:10 PortFa1_11Threshold BOOL Decimal ThresholdExceeded:11 PortFa1_12Threshold...
Page 344: 12-Port Gigabit Switches
Appendix A Data Types Table 132 - Output Data Type (12-port switches) (Continued) AB:STRATIX_5400_12PORT_MANAGED:O:0 Member Name Type Default Display Valid Values Style PortFa1_10Disable BOOL Decimal DisablePort:10 PortFa1_11Disable BOOL Decimal DisablePort:11 PortFa1_12Disable BOOL Decimal DisablePort:12 12-port Gigabit Switches Catalog numbers 1783-HMS8TG4CGN, 1783-HMS8SG4CGN, 1783-HMS4EG8CGN, 1783-HMS8TG4CGR, 1783-HMS8SG4CGR, 1783-HMS4EG8CGR Table 133 - Input Data Types (12-port Gb switches)
Page 345 Data Types Appendix A Table 133 - Input Data Types (12-port Gb switches) (Continued) AB:STRATIX_5400_12PORT_GB_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortGi1_11UnauthorizedDevice BOOL Decimal UnauthorizedDevice:11 PortGi1_12UnauthorizedDevice BOOL Decimal UnauthorizedDevice:12 AnyPortThreshold BOOL Decimal ThresholdExceeded:0 PortGi1_1Threshold BOOL Decimal ThresholdExceeded:1 PortGi1_2Threshold BOOL Decimal ThresholdExceeded:2...
Page 346: 16-Port Switches
Appendix A Data Types Table 134 - Output Data Type (12-port Gb switches) AB:STRATIX_5400_12PORT_GB_MANAGED:O:0 Member Name Type Default Display Valid Values Style AllPortsDisabled BOOL Decimal DisablePort:0 PortGi1_1Disable BOOL Decimal DisablePort:1 PortGi1_2Disable BOOL Decimal DisablePort:2 PortGi1_3Disable BOOL Decimal DisablePort:3 PortGi1_4Disable BOOL Decimal DisablePort:4 PortGi1_5Disable...
Page 347 Data Types Appendix A Table 135 - Input Data Type (16-port switches) (Continued) AB:STRATIX_5400_16PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortFa1_15Connected BOOL Decimal LinkStatus:15 PortFa1_16Connected BOOL Decimal LinkStatus:16 AnyPortUnauthorizedDevice BOOL Decimal UnauthorizedDevice:0 PortGi1_1UnauthorizedDevice BOOL Decimal UnauthorizedDevice:1 PortGi1_2UnauthorizedDevice BOOL Decimal UnauthorizedDevice:2 PortGi1_3UnauthorizedDevice...
Page 348 Appendix A Data Types Table 135 - Input Data Type (16-port switches) (Continued) AB:STRATIX_5400_16PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortGi1_2Utilization SINT Decimal PortGi1_3Utilization SINT Decimal PortGi1_4Utilization SINT Decimal PortFa1_5Utilization SINT Decimal PortFa1_6Utilization SINT Decimal PortFa1_7Utilization SINT Decimal PortFa1_8Utilization SINT Decimal...
Page 349: 16-Port Gigabit Switches
Data Types Appendix A Table 136 - Output Data Type (16-port switches) (Continued) AB:STRATIX_5400_16PORT_MANAGED:O:0 Member Name Type Default Display Valid Values Style PortFa1_14Disable BOOL Decimal DisablePort:14 PortFa1_15Disable BOOL Decimal DisablePort:15 PortFa1_16Disable BOOL Decimal DisablePort:16 16-port Gigabit Switches Catalog number 1783-HMS4SG8EG4CGN, 1783-HMS4SG8EG4CGR Table 137 - Input Data Type (16-port Gb switches) AB:STRATIX_5400_16PORT_GB_MANAGED:I:0 Member Name...
Page 350 Appendix A Data Types Table 137 - Input Data Type (16-port Gb switches) (Continued) AB:STRATIX_5400_16PORT_GB_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortGi1_8UnauthorizedDevice BOOL Decimal UnauthorizedDevice:8 PortGi1_9UnauthorizedDevice BOOL Decimal UnauthorizedDevice:9 PortGi1_10UnauthorizedDevice BOOL Decimal UnauthorizedDevice:10 PortGi1_11UnauthorizedDevice BOOL Decimal UnauthorizedDevice:11 PortGi1_12UnauthorizedDevice BOOL Decimal UnauthorizedDevice:12...
Page 351 Data Types Appendix A Table 137 - Input Data Type (16-port Gb switches) (Continued) AB:STRATIX_5400_16PORT_GB_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortGi1_12Utilization SINT Decimal PortGi1_13Utilization SINT Decimal PortGi1_14Utilization SINT Decimal PortGi1_15Utilization SINT Decimal PortGi1_16Utilization SINT Decimal MajorAlarmRelay BOOL Decimal AlarmRelay:0 MinorAlarmRelay...
Page 352: 20-Port Switches
Appendix A Data Types 20-port Switches Catalog number 1783-HMS16T4CGN Table 139 - Input Data Type (20-port switches) AB:STRATIX_5400_20PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style Fault DINT Binary AnyPortConnected BOOL Decimal LinkStatus:0 PortGi1_1Connected BOOL Decimal LinkStatus:1 PortGi1_2Connected BOOL Decimal LinkStatus:2 PortGi1_3Connected BOOL...
Page 353 Data Types Appendix A Table 139 - Input Data Type (20-port switches) (Continued) AB:STRATIX_5400_20PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortFa1_13UnauthorizedDevice BOOL Decimal UnauthorizedDevice:13 PortFa1_14UnauthorizedDevice BOOL Decimal UnauthorizedDevice:14 PortFa1_15UnauthorizedDevice BOOL Decimal UnauthorizedDevice:15 PortFa1_16UnauthorizedDevice BOOL Decimal UnauthorizedDevice:16 PortFa1_17UnauthorizedDevice BOOL Decimal UnauthorizedDevice:17 PortFa1_18UnauthorizedDevice...
Page 354 Appendix A Data Types Table 139 - Input Data Type (20-port switches) (Continued) AB:STRATIX_5400_20PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortFa1_9Utilization SINT Decimal PortFa1_10Utilization SINT Decimal PortFa1_11Utilization SINT Decimal PortFa1_12Utilization SINT Decimal PortFa1_13Utilization SINT Decimal PortFa1_14Utilization SINT Decimal PortFa1_15Utilization SINT Decimal...
Page 355: 20-Port Gigabit Switches
Data Types Appendix A Table 140 - Output Data Type (20-port switches) (Continued) AB:STRATIX_5400_20PORT_MANAGED:O:0 Member Name Type Default Display Valid Values Style PortFa1_18Disable BOOL Decimal DisablePort:18 PortFa1_19Disable BOOL Decimal DisablePort:19 PortFa1_20Disable BOOL Decimal DisablePort:20 20-port Gigabit Switches Catalog numbers 1783-HMS16TG4CGN, 1783-HMS8TG8EG4CGN, 1783-HMS16TG4CGR, 1783-HMS8TG8EG4CGR Table 141 - Input Data Type (20-port Gb switches) AB:STRATIX_5400_20PORT_GB_MANAGED:I:0...
Page 356 Appendix A Data Types Table 141 - Input Data Type (20-port Gb switches) (Continued) AB:STRATIX_5400_20PORT_GB_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortGi1_4UnauthorizedDevice BOOL Decimal UnauthorizedDevice:4 PortGi1_5UnauthorizedDevice BOOL Decimal UnauthorizedDevice:5 PortGi1_6UnauthorizedDevice BOOL Decimal UnauthorizedDevice:6 PortGi1_7UnauthorizedDevice BOOL Decimal UnauthorizedDevice:7 PortGi1_8UnauthorizedDevice BOOL Decimal UnauthorizedDevice:8...
Page 357 Data Types Appendix A Table 141 - Input Data Type (20-port Gb switches) (Continued) AB:STRATIX_5400_20PORT_GB_MANAGED:I:0 Member Name Type Default Display Valid Values Style AllPortsUtilization SINT Decimal PortGi1_1Utilization SINT Decimal PortGi1_2Utilization SINT Decimal PortGi1_3Utilization SINT Decimal PortGi1_4Utilization SINT Decimal PortGi1_5Utilization SINT Decimal PortGi1_6Utilization SINT...
Page 358 Appendix A Data Types Table 142 - Output Data Type (20-Gb port switches) (Continued) AB:STRATIX_5400_20PORT_GB_MANAGED:O:0 Member Name Type Default Display Valid Values Style PortGi1_9Disable BOOL Decimal DisablePort:9 PortGi1_10Disable BOOL Decimal DisablePort:10 PortGi1_11Disable BOOL Decimal DisablePort:11 PortGi1_12Disable BOOL Decimal DisablePort:12 PortGi1_13Disable BOOL Decimal DisablePort:13...
Page 359: Stratix 5410 Data Types
Data Types Appendix A Stratix 5410 Data Types The following tables list module-defined data types for Stratix 5410 switches. The tables include information for input (I) and output (O). Table 143 - Input Data Type AB:STRATIX_5410_28PORT_GB_MANAGED:I:0 Member Name Type Default Display Valid Values Style Fault...
Page 360 Appendix A Data Types Table 143 - Input Data Type (Continued) AB:STRATIX_5410_28PORT_GB_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortTe1_27Connected BOOL Decimal LinkStatus:27 PortGi1_27Connected PortTe1_28Connected BOOL Decimal LinkStatus:28 PortGi1_28Connected AnyPortUnauthorizedDevice BOOL Decimal UnauthorizedDevice:0 PortGi1_1UnauthorizedDevice BOOL Decimal UnauthorizedDevice:1 PortGi1_2UnauthorizedDevice BOOL Decimal UnauthorizedDevice:2 PortGi1_3UnauthorizedDevice...
Page 361 Data Types Appendix A Table 143 - Input Data Type (Continued) AB:STRATIX_5410_28PORT_GB_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortTe1_28UnauthorizedDevice BOOL Decimal UnauthorizedDevice:28 PortGi1_28UnauthorizedDevice AnyPortThreshold BOOL Decimal ThresholdExceeded:0 PortGi1_1Threshold BOOL Decimal ThresholdExceeded:1 PortGi1_2Threshold BOOL Decimal ThresholdExceeded:2 PortGi1_3Threshold BOOL Decimal ThresholdExceeded:3 PortGi1_4Threshold BOOL...
Page 362 Appendix A Data Types Table 143 - Input Data Type (Continued) AB:STRATIX_5410_28PORT_GB_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortGi1_1Utilization SINT Decimal PortGi1_2Utilization SINT Decimal PortGi1_3Utilization SINT Decimal PortGi1_4Utilization SINT Decimal PortGi1_5Utilization SINT Decimal PortGi1_6Utilization SINT Decimal PortGi1_7Utilization SINT Decimal PortGi1_8Utilization SINT...
Page 363 Data Types Appendix A Table 144 - Output Data Type AB:STRATIX_5410_28PORT_GB_MANAGED:O:0 Member Name Type Default Display Valid Values Style AllPortsDisabled BOOL Decimal DisablePort:0 PortGi1_1Disable BOOL Decimal DisablePort:1 PortGi1_2Disable BOOL Decimal DisablePort:2 PortGi1_3Disable BOOL Decimal DisablePort:3 PortGi1_4Disable BOOL Decimal DisablePort:4 PortGi1_5Disable BOOL Decimal DisablePort:5...
Page 364: Stratix 5700 And Armorstratix 5700 Data Types
Appendix A Data Types Stratix 5700 and The following tables list module-defined data types for Stratix 5700 and ArmorStratix 5700 switches. The tables include information for input (I) and ArmorStratix 5700 output (O). Data Types 6-port Gb Switches Catalog numbers 1783-BMS4S2SGL, 1783-BMS4S2SGA,1783-BMS06SGL, 1783-BM06SGA, 1783-BMS06TGL, 1783-BMS06TGA Table 145 - Input Data Types (6-port Gb switches) AB:STRATIX_5700_6PORT_GB_MANAGED:I:O...
Page 365: 6-Port Switches
Data Types Appendix A Table 145 - Input Data Types (6-port Gb switches) (Continued) AB:STRATIX_5700_6PORT_GB_MANAGED:I:O Member Name Type Default Display Valid Values Style PortGi1_2Utilization SINT Decimal MajorAlarmRelay BOOL Decimal AlarmRelay:0 MulticastGroupsActive DINT Binary Table 146 - Output Data Type (6-port Gb switches) AB:STRATIX_5700_6PORT_GB_MANAGED:O:0 Member Name Type...
Page 366 Appendix A Data Types Table 147 - Input Data Type (6-port switches) (Continued) AB:STRATIX_5700_6PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortFa1_6UnauthorizedDevice BOOL Decimal UnauthorizedDevice:6 AnyPortThreshold BOOL Decimal ThresholdExceeded:0 PortFa1_1Threshold BOOL Decimal ThresholdExceeded:1 PortFa1_2Threshold BOOL Decimal ThresholdExceeded:2 PortFa1_3Threshold BOOL Decimal ThresholdExceeded:3 PortFa1_4Threshold...
Page 367: 8-Port Switches
Data Types Appendix A 8-port Switches Catalog number 1783-ZMS8TA Table 149 - Input Data Type (8-port switches) AB:STRATIX_5700_8PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style Fault DINT Binary AnyPortConnected BOOL Decimal LinkStatus:0 PortFa1_1Connected BOOL Decimal LinkStatus:1 PortFa1_2Connected BOOL Decimal LinkStatus:2 PortFa1_3Connected BOOL...
Page 368: 10-Port Gb Switches
Appendix A Data Types Table 149 - Input Data Type (8-port switches) (Continued) AB:STRATIX_5700_8PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortFa1_7Utilization SINT Decimal PortFa1_8Utilization SINT Decimal MajorAlarmRelay BOOL Decimal AlarmRelay:0 MulticastGroupsActive DINT Binary Table 150 - Output Data Type (8-port switches) AB:STRATIX_5700_8PORT_MANAGED:O:0 Member Name Type...
Page 369 Data Types Appendix A Table 151 - Input Data Type (10-port Gb switches) (Continued) AB:STRATIX_5700_10PORT_GB_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortGi1_1Connected BOOL Decimal LinkStatus:9 PortGi1_2Connected BOOL Decimal LinkStatus:10 AnyPortUnauthorizedDevice BOOL Decimal UnauthorizedDevice:0 PortFa1_1UnauthorizedDevice BOOL Decimal UnauthorizedDevice:1 PortFa1_2UnauthorizedDevice BOOL Decimal UnauthorizedDevice:2...
Page 370: 10-Port Switches
Appendix A Data Types Table 152 - Output Data Type (10-port Gb switches) AB:STRATIX_5700_10PORT_MANAGED:O:0 Member Name Type Default Display Valid Values Style AllPortsDisabled BOOL Decimal DisablePort:0 PortFa1_1Disable BOOL Decimal DisablePort:1 PortFa1_2Disable BOOL Decimal DisablePort:2 PortFa1_3Disable BOOL Decimal DisablePort:3 PortFa1_4Disable BOOL Decimal DisablePort:4 PortFa1_5Disable...
Page 371 Data Types Appendix A Table 153 - Input Data Type (10-port switches) (Continued) AB:STRATIX_5700_10PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortFa1_6UnauthorizedDevice BOOL Decimal UnauthorizedDevice:6 PortFa1_7UnauthorizedDevice BOOL Decimal UnauthorizedDevice:7 PortFa1_8UnauthorizedDevice BOOL Decimal UnauthorizedDevice:8 PortFa1_9UnauthorizedDevice BOOL Decimal UnauthorizedDevice:9 PortFa1_10UnauthorizedDevice BOOL Decimal UnauthorizedDevice:10 AnyPortThreshold...
Page 372: 16-Port Switches
Appendix A Data Types Table 154 - Output Data Type (10-port switches) AB:STRATIX_5700_10PORT_MANAGED:O:0 Member Name Type Default Display Valid Values Style AllPortsDisabled BOOL Decimal DisablePort:0 PortFa1_1Disable BOOL Decimal DisablePort:1 PortFa1_2Disable BOOL Decimal DisablePort:2 PortFa1_3Disable BOOL Decimal DisablePort:3 PortFa1_4Disable BOOL Decimal DisablePort:4 PortFa1_5Disable BOOL...
Page 373 Data Types Appendix A Table 155 - Input Data Type (16-port switches) (Continued) AB:STRATIX_5700_16PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style AnyPortUnauthorizedDevice BOOL Decimal UnauthorizedDevice:0 PortFa1_1UnauthorizedDevice BOOL Decimal UnauthorizedDevice:1 PortFa1_2UnauthorizedDevice BOOL Decimal UnauthorizedDevice:2 PortFa1_3UnauthorizedDevice BOOL Decimal UnauthorizedDevice:3 PortFa1_4UnauthorizedDevice BOOL Decimal UnauthorizedDevice:4 PortFa1_5UnauthorizedDevice...
Page 374 Appendix A Data Types Table 155 - Input Data Type (16-port switches) (Continued) AB:STRATIX_5700_16PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortFa1_4Utilization SINT Decimal PortFa1_5Utilization SINT Decimal PortFa1_6Utilization SINT Decimal PortFa1_7Utilization SINT Decimal PortFa1_8Utilization SINT Decimal PortFa1_9Utilization SINT Decimal PortFa1_10Utilization SINT Decimal...
Page 375: 20-Port Gb Switches
Data Types Appendix A 20-port Gb Switches Catalog numbers 1783-BMS20CGL, 1783-BMS20CGN, 1783-BMS20CGP, 1783-BMS20CGPK Table 157 - Input Data Type (20-port Gb switches) AB:STRATIX_5700_20PORT_GB_MANAGED:I:0 Member Name Type Default Valid Values Display Style Fault DINT Binary AnyPortConnected BOOL Decimal LinkStatus:0 PortFa1_1Connected BOOL Decimal LinkStatus:1 PortFa1_2Connected...
Page 376 Appendix A Data Types Table 157 - Input Data Type (20-port Gb switches) (Continued) AB:STRATIX_5700_20PORT_GB_MANAGED:I:0 Member Name Type Default Valid Values Display Style PortFa1_12UnauthorizedDevice BOOL Decimal UnauthorizedDevice:12 PortFa1_13UnauthorizedDevice BOOL Decimal UnauthorizedDevice:13 PortFa1_14UnauthorizedDevice BOOL Decimal UnauthorizedDevice:14 PortFa1_15UnauthorizedDevice BOOL Decimal UnauthorizedDevice:15 PortFa1_16UnauthorizedDevice BOOL Decimal UnauthorizedDevice:16...
Page 377: 18-Port Gb Switches
Data Types Appendix A Table 157 - Input Data Type (20-port Gb switches) (Continued) AB:STRATIX_5700_20PORT_GB_MANAGED:I:0 Member Name Type Default Valid Values Display Style PortFa1_8Utilization SINT Decimal PortFa1_9Utilization SINT Decimal PortFa1_10Utilization SINT Decimal PortFa1_11Utilization SINT Decimal PortFa1_12Utilization SINT Decimal PortFa1_13Utilization SINT Decimal PortFa1_14Utilization SINT...
Page 378 Appendix A Data Types Table 158 - Input Data Type (18-port Gb switches) (Continued) AB:STRATIX_5700_18PORT_GB_MANAGED:I:0 Member Name Type Default Valid Values Display Style PortFa1_13Connected BOOL Decimal LinkStatus:13 PortFa1_14Connected BOOL Decimal LinkStatus:14 PortFa1_15Connected BOOL Decimal LinkStatus:15 PortFa1_16Connected BOOL Decimal LinkStatus:16 PortGi1_1Connected BOOL Decimal LinkStatus:19...
Page 379 Data Types Appendix A Table 158 - Input Data Type (18-port Gb switches) (Continued) AB:STRATIX_5700_18PORT_GB_MANAGED:I:0 Member Name Type Default Valid Values Display Style PortFa1_13Threshold BOOL Decimal ThresholdExceeded:13 PortFa1_14Threshold BOOL Decimal ThresholdExceeded:14 PortFa1_15Threshold BOOL Decimal ThresholdExceeded:15 PortFa1_16Threshold BOOL Decimal ThresholdExceeded:16 PortGi1_1Threshold BOOL Decimal ThresholdExceeded:19...
Page 380 Appendix A Data Types Table 159 - Output Data Type (18-port Gb switches) (Continued) AB:STRATIX_5700_20PORT_GB_MANAGED:O:0 Member Name Type Default Display Valid Values Style PortFa1_6Disable BOOL Decimal DisablePort:6 PortFa1_7Disable BOOL Decimal DisablePort:7 PortFa1_8Disable BOOL Decimal DisablePort:8 PortFa1_9Disable BOOL Decimal DisablePort:9 PortFa1_10Disable BOOL Decimal DisablePort:10...
Page 381: 20-Port Gb Switches
Data Types Appendix A 20-port Gb Switches Catalog numbers 1783-BMS20CGL, 1783-BMS20CGN, 1783-BMS20CGP, 1783-BMS20CGPK Table 160 - Input Data Type (20-port Gb switches) AB:STRATIX_5700_20PORT_GB_MANAGED:I:0 Member Name Type Default Valid Values Display Style Fault DINT Binary AnyPortConnected BOOL Decimal LinkStatus:0 PortFa1_1Connected BOOL Decimal LinkStatus:1 PortFa1_2Connected...
Page 382 Appendix A Data Types Table 160 - Input Data Type (20-port Gb switches) (Continued) AB:STRATIX_5700_20PORT_GB_MANAGED:I:0 Member Name Type Default Valid Values Display Style PortFa1_12UnauthorizedDevice BOOL Decimal UnauthorizedDevice:12 PortFa1_13UnauthorizedDevice BOOL Decimal UnauthorizedDevice:13 PortFa1_14UnauthorizedDevice BOOL Decimal UnauthorizedDevice:14 PortFa1_15UnauthorizedDevice BOOL Decimal UnauthorizedDevice:15 PortFa1_16UnauthorizedDevice BOOL Decimal UnauthorizedDevice:16...
Page 383 Data Types Appendix A Table 160 - Input Data Type (20-port Gb switches) (Continued) AB:STRATIX_5700_20PORT_GB_MANAGED:I:0 Member Name Type Default Valid Values Display Style PortFa1_8Utilization SINT Decimal PortFa1_9Utilization SINT Decimal PortFa1_10Utilization SINT Decimal PortFa1_11Utilization SINT Decimal PortFa1_12Utilization SINT Decimal PortFa1_13Utilization SINT Decimal PortFa1_14Utilization SINT...
Page 384: 20-Port Switches
Appendix A Data Types Table 161 - Output Data Type (20-port Gb switches) (Continued) AB:STRATIX_5700_20PORT_GB_MANAGED:O:0 Member Name Type Default Valid Values Display Style PortFa1_18Disable BOOL Decimal DisablePort:18 PortGi1_1Disable BOOL Decimal DisablePort:19 PortGi1_2Disable BOOL Decimal DisablePort:20 20-port Switches Catalog numbers 1783-BMS20CL, 1783-BMS20CA Table 162 - Input Data Type (20-port switches) AB:STRATIX_5700_20PORT_MANAGED:I:0 Member Name...
Page 385 Data Types Appendix A Table 162 - Input Data Type (20-port switches) (Continued) AB:STRATIX_5700_20PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortFa1_4UnauthorizedDevice BOOL Decimal UnauthorizedDevice:4 PortFa1_5UnauthorizedDevice BOOL Decimal UnauthorizedDevice:5 PortFa1_6UnauthorizedDevice BOOL Decimal UnauthorizedDevice:6 PortFa1_7UnauthorizedDevice BOOL Decimal UnauthorizedDevice:7 PortFa1_8UnauthorizedDevice BOOL Decimal UnauthorizedDevice:8 PortFa1_9UnauthorizedDevice...
Page 386 Appendix A Data Types Table 162 - Input Data Type (20-port switches) (Continued) AB:STRATIX_5700_20PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style AllPortsUtilization SINT Decimal PortFa1_1Utilization SINT Decimal PortFa1_2Utilization SINT Decimal PortFa1_3Utilization SINT Decimal PortFa1_4Utilization SINT Decimal PortFa1_5Utilization SINT Decimal PortFa1_6Utilization SINT Decimal...
Page 387: 24-Port Switches
Data Types Appendix A Table 163 - Output Data Type (20-port switches) (Continued) AB:STRATIX_5700_20PORT_MANAGED:O:0 Member Name Type Default Display Valid Values Style PortFa1_10Disable BOOL Decimal DisablePort:10 PortFa1_11Disable BOOL Decimal DisablePort:11 PortFa1_12Disable BOOL Decimal DisablePort:12 PortFa1_13Disable BOOL Decimal DisablePort:13 PortFa1_14Disable BOOL Decimal DisablePort:14 PortFa1_15Disable...
Page 388 Appendix A Data Types Table 164 - Input Data Type (24-port switches) (Continued) AB:STRATIX_5700_24PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortFa1_17Connected BOOL Decimal LinkStatus:17 PortFa1_18Connected BOOL Decimal LinkStatus:18 PortFa1_19Connected BOOL Decimal LinkStatus:19 PortFa1_20Connected BOOL Decimal LinkStatus:20 PortFa1_21Connected BOOL Decimal LinkStatus:21 PortFa1_22Connected...
Page 389 Data Types Appendix A Table 164 - Input Data Type (24-port switches) (Continued) AB:STRATIX_5700_24PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortFa1_5Threshold BOOL Decimal ThresholdExceeded:5 PortFa1_6Threshold BOOL Decimal ThresholdExceeded:6 PortFa1_7Threshold BOOL Decimal ThresholdExceeded:7 PortFa1_8Threshold BOOL Decimal ThresholdExceeded:8 PortFa1_9Threshold BOOL Decimal ThresholdExceeded:9 PortFa1_10Threshold...
Page 390 Appendix A Data Types Table 164 - Input Data Type (24-port switches) (Continued) AB:STRATIX_5700_24PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortFa1_18Utilization SINT Decimal PortFa1_19Utilization SINT Decimal PortFa1_20Utilization SINT Decimal PortFa1_21Utilization SINT Decimal PortFa1_22Utilization SINT Decimal PortFa1_23Utilization SINT Decimal PortFa1_24Utilization SINT Decimal...
Page 391: Stratix 8000 And 8300 Data Types
Data Types Appendix A Table 165 - Output Data Type (24-port switches) (Continued) AB:STRATIX_5700_24PORT_MANAGED:O:0 Member Name Type Default Display Valid Values Style PortFa1_22Disable BOOL Decimal DisablePort:22 PortFa1_23Disable BOOL Decimal DisablePort:23 PortFa1_24Disable BOOL Decimal DisablePort:24 The following tables show input and output data types for all 26 ports of the Stratix 8000 and 8300 switch, as well as port assignments for data types.
Page 392 Appendix A Data Types Table 166 - Input Data Types (Continued) Tag Name Type Description AnyPortUnauthorizedDevice BOOL Indicates that an unauthorized MAC ID has attempted to communicate on any port. PortGi1_1UnauthorizedDevice BOOL Indicates that an unauthorized MAC ID has attempted to communicate on a particular port.
Page 393 Data Types Appendix A Table 166 - Input Data Types (Continued) Tag Name Type Description PortGi1_1Threshold BOOL Indicates that unicast, multicast, or broadcast threshold limit has been exceeded on a particular port. PortGi1_2Threshold BOOL 0 = OK 1 = Threshold exceeded PortFa1_1Threshold BOOL PortFa1_2Threshold...
Page 394 Appendix A Data Types Table 166 - Input Data Types (Continued) Tag Name Type Description PortGi1_1Utilization; SINT The percentage of the bandwidth utilized on a particular port. PortGi1_2Utilization; SINT PortFa1_1Utilization; SINT PortFa1_2Utilization; SINT PortFa1_3Utilization; SINT PortFa1_4Utilization; SINT PortFa1_5Utilization; SINT PortFa1_6Utilization; SINT PortFa1_7Utilization;...
Page 395 Data Types Appendix A Table 167 - Output Data Types Tag Name Type Description AllPortsDisable BOOL Setting this bit disables all ports on the switch. 0 = Enable 1 = Disable PortGi1_1Disable BOOL Setting a particular bit disables that particular port. 0 = Enable PortGi1_2Disable BOOL...
Page 396 Appendix A Data Types Notes: Rockwell Automation Publication 1783-UM007I-EN-P - December 2017...
Page 397 Appendix Port Assignments for CIP Data Topic Page Stratix 5400 Port Assignments Stratix 5410 Port Assignments Stratix 5700 Port Assignments ArmorStratix 5700 Port Assignments Stratix 8000 and 8300 Port Assignments The following tables identify the instance numbers of the Ethernet link objects that are associated with each port on the switch.
Page 398: Stratix 5400 Port Assignments
Appendix B Port Assignments for CIP Data Stratix 5400 Port Assignments Table 168 - 8- and 12-port Switches 1783-HMS4C4CGN 1783-HMS8T4CGN 1783-HMS8S4CGN 1783-HMS4T4E4CGN 1783-HMS8TG4CGN 1783-HMS8SG4CGN 1783-HMS4EG8CGN 1783-HMS8TG4CGR 1783-HMS8SG4CGR 1783-HMS4EG8CGR 0 Any/All ports Any/All ports Any/All ports Any/All ports Any/All ports Any/All ports...
Page 399 Port Assignments for CIP Data Appendix B Table 169 - 16- and 20-port Switches 1783-HMS4S8E4CGN 1783-HMS4SG8EG4CGN 1783-HMS16T4CGN 1783-HMS16TG4CGN 1783-HMS8TG8EG4CGN 1783-HMS4SG8EG4CGR 1783-HMS16TG4CGR 1783-HMS8TG8EG4CGR 0 Any/All ports Any/All ports Any/All ports Any/All ports Any/All ports 1 Gi1/1 Gi1/1 Gi1/1 Gi1/1 Gi1/1 2 Gi1/2 Gi1/2 Gi1/2 Gi1/2...
Page 400: Stratix 5410 Port Assignments
Appendix B Port Assignments for CIP Data Stratix 5410 1783-IMS28NDC, 1783-IMS28NAC, 1783-IMS28GNDC, 1783-IMS28GNAC, 1783-IMS28RDC, 1783-IMS28RAC, 1783-IMS28GRDC, 1783-IMS28GRAC Port Assignments 0 Any/All ports 1 Gi1/1 2 Gi1/2 3 Gi1/3 4 Gi1/4 5 Gi1/5 6 Gi1/6 7 Gi1/7 8 Gi1/8 9 Gi1/9 10 Gi1/10 11 Gi1/11 12 Gi1/12...
Page 401: Stratix 5700 Port Assignments
Port Assignments for CIP Data Appendix B Stratix 5700 Port Assignments Table 170 - 6- and 10-port Switches 1783-BMS4S2SGL, 1783-BMS4S2SGA, 1783-BMS06TGL, 1783-BMS10CL, 1783-BMS10CGL, 1783-BMS10CGA, 1783-BMS06SL, 1783-BMS06SA, 1783-BMS10CGP, 1783-BMS10CGN 1783-BMS06TGA 1783-BMS10CA 1783-BMS06TL, 1783-BMS06TA, 1783-BMS06SGL, 1783-BMS06SGA 0 Any/All ports Any/All ports Any/All ports Any/All ports 1 Fa1/1 Fa/1...
Page 402: Armorstratix 5700 Port Assignments
Appendix B Port Assignments for CIP Data Table 171 - 18- and 20-port Switches (Continued) 1783-BMS12T4E2CGL, 1783-BMS12T4E2CGP, 1783-BMS20CL, 1783-BMS20CA 1783-BMS20CGL, 1783-BMS20CGN, 1783-BMS12T4E2CGNK 1783-BMS20CGP, 1783-BMS20CGPK Fa1/19 Gi1/1 Fa1/20 Gi1/2 27 SVI1 SVI1 SVI1 ArmorStratix 5700 Port Assignments 1783-ZMS8TA 1783-ZMS4T4E2TGP, 1783-ZMS16TA 1783-ZMS8T8E2TGP, 1783-ZMS24TA 1783-ZMS4T4E2TGN 1783-ZMS8T8E2TGN...
Page 403: Stratix 8000 And 8300 Port Assignments
Port Assignments for CIP Data Appendix B Stratix 8000 and 8300 Port Assignments 6-port Managed 10-port Managed 10-port Managed 14-port Managed 14-port Managed 14-port Managed 18-port Managed Ethernet Switch Ethernet Switch Ethernet Switch Ethernet Switch Ethernet Switch Ethernet Switch Ethernet Switch 0 Any/All ports Any/All ports Any/All ports...
Page 404 Appendix B Port Assignments for CIP Data Notes: Rockwell Automation Publication 1783-UM007I-EN-P - December 2017...
Page 405 Appendix Port Numbering Topic Page Stratix 5400 Port Numbering Stratix 5410 Port Numbering Stratix 5700 Port Numbering ArmorStratix 5700 Port Numbering Stratix 8000 and 8300 Port Numbering Rockwell Automation Publication 1783-UM007I-EN-P - December 2017...
Page 406: Stratix 5400 Port Numbering
• Unit number (always 1) • Port number (1…20, depending on the catalog number) Gigabit Ethernet is abbreviated as Gi and Fast Ethernet as Fa. Table 172 - Stratix 5400 Port Numbering Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.txt Text File...
Page 407 Port Numbering Appendix C Table 172 - Stratix 5400 Port Numbering (Continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.txt Text File 1783-HMS4T4E4CGN 12-port (4 combo Gigabit ports; 4 Ethernet ports; Gi1/1 4 PoE/PoE+ ports) managed switch; Layer 2 firmware...
Page 408 Appendix C Port Numbering Table 172 - Stratix 5400 Port Numbering (Continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.txt Text File 1783-HMS4S8E4CGN 16-port (4 combo Gigabit ports; 8 PoE/PoE+ ports; Gi1/1 4 SFP ports) managed switch; Layer 2 firmware...
Page 409 Port Numbering Appendix C Table 172 - Stratix 5400 Port Numbering (Continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.txt Text File 1783-HMS16T4CGN 20-port (4 combo Gigabit ports; 16 Ethernet ports) Gi1/1 managed switch; Layer 2 firmware...
Page 410 Appendix C Port Numbering Table 172 - Stratix 5400 Port Numbering (Continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.txt Text File 1783-HMS8TG8EG4CGN 20-port (8 Gigabit ports; 4 Gigabit combo ports; 8 Gigabit Gi1/1 PoE/PoE+ ports) managed switch; Layer 2 firmware...
Page 411 Port Numbering Appendix C Table 172 - Stratix 5400 Port Numbering (Continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.txt Text File 1783-HMS4EG8CGR 12-port (4 Gigabit ports; 4 Gigabit combo ports; 4 Gigabit Gi1/1 PoE/PoE+ ports) managed switch; Layer 3 firmware...
Page 412 Appendix C Port Numbering Table 172 - Stratix 5400 Port Numbering (Continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.txt Text File 1783-HMS4SG8EG4CGR 16-port (4 Gigabit combo ports; 8 Gigabit PoE/PoE+ ports; Gi1/1 4 Gigabit SFP ports) managed switch; Layer 3 firmware...
Page 413 Port Numbering Appendix C Table 172 - Stratix 5400 Port Numbering (Continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.txt Text File 1783-HMS8TG8EG4CGR 20-port (8 Gigabit ports; 4 Gigabit combo ports; 8 Gigabit Gi1/1 PoE/PoE+ ports) managed switch; Layer 3 firmware...
Page 414: Stratix 5410 Port Numbering
Appendix C Port Numbering Stratix 5410 Port Numbering The port ID consists of the following: • Port type (Gigabit Ethernet or 10 Gigabit Ethernet) • Unit number (always 1)) • Port number (1…28) Gigabit Ethernet is abbreviated as Gi and 10 Gigabit Ethernet as Te. Table 173 - Stratix 5410 Port Numbering Cat.
Page 415: Stratix 5700 Port Numbering
Port Numbering Appendix C Stratix 5700 Port Numbering The port ID consists of the following: • Port type (Gigabit Ethernet for Gigabit ports and Fast Ethernet for 10/100 Mbps ports) • Unit number (always 1) • Port number (1…2 for Gigabit ports, 1…18 for all others, depending on the catalog number) Gigabit Ethernet is abbreviated as Gi and Fast Ethernet as Fa.
Page 416 Appendix C Port Numbering Table 174 - Stratix 5700 Port Numbering (Continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.text File 1783-BM06SGA 6-port (4 Ethernet ports; 2 SFP Gigabit slots) managed switch; Fa1/1 full firmware Fa1/2 Fa1/3 Fa1/4 Gi1/1...
Page 417 Port Numbering Appendix C Table 174 - Stratix 5700 Port Numbering (Continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.text File 1783-BMS10CGA 10-port (8 Ethernet ports; 2 combo Gigabit ports) managed switch; Fa1/1 full firmware Fa1/2 Fa1/3 Fa1/4 Fa1/5...
Page 418 Appendix C Port Numbering Table 174 - Stratix 5700 Port Numbering (Continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.text File 1783-BMS12T4E2CGP 18-port (12 Ethernet ports; 4 PoE/PoE+ ports; 2 combo Gigabit ports) Fa1/1 managed switch; full firmware; PTP Fa1/2 Fa1/3 Fa1/4...
Page 419 Port Numbering Appendix C Table 174 - Stratix 5700 Port Numbering (Continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.text File 1783-BMS20CA 20-port (16 Ethernet ports; 2 SFP slots; 2 combo ports) managed Fa1/1 switch; full firmware Fa1/2 Fa1/3 Fa1/4...
Page 420 Appendix C Port Numbering Table 174 - Stratix 5700 Port Numbering (Continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.text File 1783-BMS20CGN 20-port (16 Ethernet ports; 2 SFP slots; 2 combo Gigabit ports) Fa1/1 managed switch; full firmware; PTP; NAT Fa1/2 Fa1/3 Fa1/4...
Page 421 Port Numbering Appendix C Table 174 - Stratix 5700 Port Numbering (Continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.text File 1783-BMS20CGPK 20-port (16 Ethernet ports; 2 SFP slots; 2 combo Gigabit ports) Fa1/1 managed switch; full firmware; PTP; conformal coating Fa1/2 Fa1/3 Fa1/4...
Page 422: Armorstratix 5700 Port Numbering
Appendix C Port Numbering ArmorStratix 5700 The port ID consists of the following: • Port type (Gigabit Ethernet for Gigabit ports and Fast Ethernet for Port Numbering 10/100 Mbps ports) • Unit number (always 1) • Port number (1…2 for Gigabit ports, 1…18 for all others, depending on the catalog number) Gigabit Ethernet is abbreviated as Gi and Fast Ethernet as Fa.
Page 423 Port Numbering Appendix C Table 175 - ArmorStratix 5700 Port Numbering (Continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.text File 1783-ZMS8T8E2TGP 18-port (2 Gigabit ports; 8 Ethernet ports; 8 PoE/PoE+ ports) GE-1 Gi1/1 managed switch; full firmware; PTP GE-2 Gi1/2 Fa1/1...
Page 424 Appendix C Port Numbering Table 175 - ArmorStratix 5700 Port Numbering (Continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.text File 1783-ZMS24TA 24-port (24 Ethernet ports) managed switch; full firmware Fa1/1 Fa1/2 Fa1/3 Fa1/4 Fa1/5 Fa1/6 Fa1/7 Fa1/8 Fa1/9...
Page 425: Stratix 8000 And 8300 Port Numbering
Port Numbering Appendix C Stratix 8000 and 8300 The port ID consists of the following: • Port type (Gigabit Ethernet for Gigabit ports and Fast Ethernet for Port Numbering 10/100 Mbps ports) • Unit number (1, 2, or 3) • Port number (1…2 for Gigabits, 1…4 for the 6-port base and 1…8 for all others) Gigabit Ethernet is abbreviated as Gi and Fast Ethernet as Fa.
Page 426 Appendix C Port Numbering Table 176 - Stratix 8000/8300 Switch and Expansion Module Port Numbering (Continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.txt Text File 1783-MX04E 4-port (4 PoE ports) expansion module Fa#/1 Fa#/2 Fa#/3 Fa#/4 1783-MX04T04E 8-port(4 Ethernet ports;...
Page 427: Stratix 5410 Cables And Connectors
Cables and Connectors Topic Page Stratix 5410 Cables and Connectors Stratix 5400 and 5700 Cables and Connectors ArmorStratix 5700 Cables and Connectors Stratix 8000/8300 Cables and Connectors For recommended cables and SFP modules, see the Stratix Ethernet Device Specifications Technical Data, publication 1783-TD001.
Page 428: Connect To 10Base-T- And 100Base-Tx-Compatible Devices
Appendix D Cables and Connectors Connect to 10BASE-T- and 100BASE-TX-Compatible Devices The auto-MDIX feature is enabled by default. Follow these cabling guidelines when the auto-MDIX feature has been disabled. When connecting the ports to 10BASE-T- and 100BASE-TX-compatible devices, such as servers and routers, you can use a two or four twisted-pair, straight-through cable that is wired for 10BASE-T and 100BASE-TX.
Page 429 Cables and Connectors Appendix D You can use Category 3, 4, or 5 cabling when connecting to 10BASE-T- compatible devices. You must use Category 5 cabling when connecting to 100BASE-TX-compatible devices. IMPORTANT Use a four twisted-pair, Category 5 cable when connecting to a 1000BASE-T- compatible device or PoE port.
Page 430: Console Ports
Appendix D Cables and Connectors Console Ports Console ports enable you to connect a switch to a computer if you use the Command-line interface (CLI) to configure and monitor a switch. Stratix 5410 switches have these console ports: • A USB 5-pin mini-Type B port on the front panel •...
Page 431 Cables and Connectors Appendix D The following table lists the pinouts for the console port, the RJ45-to-DB-9 adapter cable, and the console device. Table 177 - Pinouts with DB-9 Pin Switch Console Port (DTE) RJ45-to-DB-9 Terminal Adapter Console Device Signal DB-9 Pin Signal The following table lists the pinouts for the console port, RJ45-to-DB-25...
Page 432: Alarm Port
Appendix D Cables and Connectors Alarm Port The front panel alarm port uses an RJ45 connector. Figure 61 - Front Panel Alarm Connector Figure 62 - Alarm Connector Pinout Label 4 5 6 7 8 Alarm 1 input Alarm 2 input Alarm output normally closed Alarm 3 input Alarm 4 input...
Page 433: Stratix 5400 And 5700 Cables And Connectors
Cables and Connectors Appendix D Stratix 5400 and 5700 This section describes how to connect to ports on Stratix 5400 and Stratix 5700 switches. Cables and Connectors 10/100 and 10/100/1000 Ports The 10/100 and 10/100/1000 Ethernet ports use standard RJ45 connectors and Ethernet pinouts with internal crossovers.
Page 434: Connect To 10Base-T- And 100Base-Tx-Compatible Devices
Appendix D Cables and Connectors Connect to 10BASE-T- and 100BASE-TX-Compatible Devices The auto-MDIX feature is enabled by default. Follow these cabling guidelines when the auto-MDIX feature has been disabled. When connecting the ports to 10BASE-T- and 100BASE-TX-compatible devices, such as servers and routers, you can use a two or four twisted-pair, straight-through cable that is wired for 10BASE-T and 100BASE-TX.
Page 435: Dual-Purpose Ports (Combo Ports)
Cables and Connectors Appendix D You can use Category 3, 4, or 5 cabling when connecting to 10BASE-T- compatible devices. You must use Category 5 cabling when connecting to 100BASE-TX-compatible devices. IMPORTANT Use a four twisted-pair, Category 5 cable when connecting to a 1000BASE-T- compatible device or PoE port.
Page 436: Console Ports
Appendix D Cables and Connectors Console Ports Console ports enable you to connect a switch to a computer if you use the Command-line interface (CLI) to configure and monitor a switch. Stratix 5700 switches have these console ports: • A USB 5-pin mini-Type B port on the front panel The USB console port uses a USB Type A to 5-pin mini-Type B cable.
Page 437 Cables and Connectors Appendix D The following table lists the pinouts for the console port, the RJ45-to-DB-9 adapter cable, and the console device. Table 179 - Pinouts with DB-9 Pin Switch Console Port (DTE) RJ45-to-DB-9 Terminal Adapter Console Device Signal DB-9 Pin Signal The following table lists the pinouts for the console port, RJ45-to-DB-25...
Page 438: Alarm Ports
Appendix D Cables and Connectors Alarm Ports The front-panel alarm-relay connector ports are described in the following illustration and table. Figure 71 - Wiring Example for Alarm Inputs and Outputs Alarms Connector To Alarm Input Alarm +24V DC from User Relay Coil To Alarm Input...
Page 439: Armorstratix 5700 Cables And Connectors
Cables and Connectors Appendix D ArmorStratix 5700 This section describes how to connect to ports on ArmorStratix 5700 switches. Cables and Connectors 10/100 Ports The 10/100 Ethernet ports use M12 D-coded 4-pin connectors and Ethernet pinouts with twisted-pair crossovers or straight-through cables. Figure 72 - 10/100 Connector Pinouts 100/1000 Ports The 100/1000 Ethernet ports use M12 X-coded 8-pin connectors and...
Page 440: Connect To 10Base-T- And 100Base-Tx-Compatible Devices
Appendix D Cables and Connectors Connect to 10BASE-T- and 100BASE-TX-Compatible Devices The auto-MDIX feature is enabled by default. Follow these cabling guidelines when the auto-MDIX feature has been disabled. When connecting the ports to 10BASE-T- and 100BASE-TX-compatible devices, such as servers and routers, you can use a two or four twisted-pair, straight-through cable that is wired for 10BASE-T and 100BASE-TX.
Page 441 Cables and Connectors Appendix D When connecting the ports to 10BASE-T- and 100BASE-TX-compatible devices, such as switches or repeaters, you can use a two or four twisted-pair, crossover cable. Use a straight-through cable to connect two ports when only one port is designated with an X.
Page 442: Console Port
Connect to the console port with an M12-to-DB-9 cable (Figure 78): • Obtain a male 5-pin DC Micro-style (M12) connector configuration cordset, such as Allen-Bradley Bulletin 889D. • Obtain a DB-9 connector and attach it to one end of the cable. Figure 78 - M12-to-DB-9 Cable 32552-M...
Page 443: Alarm Ports
Alarm ports are included only on ArmorStratix 5700 switches with PoE. Figure 81 shows the front-panel alarm relay connector and ports. The alarm connector uses a male 5-pin DC Micro-style (M12) connector configuration cordset, such as Allen-Bradley Bulletin 889D. Figure 81 - Alarm Connector Pinout Unconnected Unconnected...
Page 444: Poe Port Cable Specifications
Appendix D Cables and Connectors PoE Port Cable Specifications For PoE ports, use a Category 5 (Cat 5) cable with a distance of up to 100 m (328 ft). Stratix 8000/8300 This section describes how to connect to ports on Stratix 8000/8300 switches. Cables and Connectors 10/100 and 10/100/1000 Ports The 10/100 and 10/100/1000 Ethernet ports use standard RJ45 connectors...
Page 445: Connect To 10Base-T- And 100Base-Tx-Compatible Devices
Cables and Connectors Appendix D The PoE ports on the PoE expansion modules integrate power and data signals on the same wires. The ports use standard RJ45 connectors and Ethernet pinouts with internal crossovers. Figure 85 - 10/100 PoE Connector Pinouts and Power Sourcing Equipment (PSE) Voltage Label Alternative A (MDI) 4 5 6 7 8...
Page 446 Appendix D Cables and Connectors When connecting the ports to 10BASE-T- and 100BASE-TX-compatible devices, such as switches or repeaters, you can use a two or four twisted-pair, crossover cable. Use a straight-through cable to connect two ports only when one port is designated with an X.
Page 447: 100Base-Fx Ports
Cables and Connectors Appendix D 100Base-FX Ports The 100Base-FX ports use the following: • LC connectors, as shown in the following figure • 50/125- or 62.5 /125-micron multimode fiber-optic cables Figure 90 - Fiber-optic SFP Module LC Connector ATTENTION: Invisible laser radiation can be emitted from disconnected fibers or connectors.
Page 448: Console Port
Appendix D Cables and Connectors Console Port The console port enables you to connect the switch to a computer if you use the Command-line interface (CLI) to configure and monitor the switch. The console port uses an 8-pin RJ45 connector. The supplied RJ45-to-DB-9 adapter cable connects the console port of the switch to a computer.
Page 449: Poe Port Cable Specifications
Cables and Connectors Appendix D The following table lists the pinouts for the console port, RJ45-to-DB-25 female DTE adapter, and the console device. The RJ45-to-DB-25 female DTE adapter is not supplied with the switch. Table 182 - Pinouts with DB-25 Pin Switch Console Port (DTE) RJ45-to-DB-25 Terminal Adapter Console Device...
Page 450 Appendix D Cables and Connectors Notes: Rockwell Automation Publication 1783-UM007I-EN-P - December 2017...
Page 451: Index
Index access via console port 70 access Device Manager 46 access via SSH 38 access management 71 access via Telnet 70 access port clock modes choose 51 Boundary 84 VLAN 0 priority tagging 244 End to End Transparent 85 … ACLs 74 Forward 85 NTP-PTP 85...
Page 452 Index active DHCP server IP address 117 global macros compatible switches 16 for CIP traffic 42 configure via Device Manager 115 for motion traffic 42 configure via Logix Designer application 119 global navigation satellite system. See GNSS considerations 105 GNSS 20 DHCP 111 enable CIP 117 GNSS status 293...
Page 453 Index locate switch Multi-mode Express Setup via Device Manager 286 overview 30 via Logix Designer application 300 requirements 26 logout 46 Multiple Spanning Tree Protocol (MSTP) 272 Long Press mode Express Setup multiple VLANs for DLR 103 overview 30 run 33 low priority PoE ports 232 configuration considerations 167 configuration overview 160...
Page 454 Index cable specifications 449 compatible switches 16 compatible switches 17 configure via Device Manager 86 configure via Device Manager Web interface configure via Logix Designer application 94 overview 84 … features 232 PTP modes initial power allocation 233 Boundary 84 pinouts 433 End to End Transparent 85 power management modes 234...
Page 455 153 port 229 Static mode, PoE 235 traffic level 227 status indicators time synchronization Stratix 5400 290 configure via Device Manager 86 Stratix 5410 293 configure via Logix Designer application 94 Stratix 8000/8300 295 timing message settings 86...
Page 456 Index troubleshoot Device Manager display 333 DHCP 333 firmware upgrade 68 IP address problems 333 PRP 218 reset switch 336 speed, duplex, and autonegotiation 334 switch 329 switch performance 334 wrong IP address 333 trunk port choose 51 VLAN 0 priority tagging 244 unicast storm 227 upgrade firmware 68 VLAN 0 priority tagging...
Page 458: Documentation Feedback
Rockwell Automation maintains current product environmental information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page. Allen-Bradley, ArmorStratix, Rockwell Automation, Rockwell Software, RSLogix 5000, RSNetWorx, Stratix, Studio 5000, and Studio 5000 Logix Designer are trademarks of RockwellAutomation, Inc. Trademarks not belonging to Rockwell Automation are property of their respective companies.

This manual is also suitable for:

Stratix 8000 Stratix 8300 Stratix 5410 Armorstratix 5700 Stratix 5700

Allen-Bradley Stratix 5400 User Manual

Preface

About the Switches

Chapter 1 Stratix Managed Switches

Get Started

Chapter 2 Express Setup Overview

Configure Switch Features

Chapter 3 Access Control Lists (Acls)

Monitor the Switch

Chapter 4 Switch Status Via Device Manager

Troubleshoot the Switch

Chapter 5 Troubleshoot the Installation

Appendix A Stratix 5400 Data Types

Stratix 5400 Port Assignments

Appendix B

Appendix C Stratix 5400 Port Numbering

Appendix D

Stratix 5410 Cables and Connectors

Index

Quick Links

Related Manuals for Allen-Bradley Stratix 5400

Summary of Contents for Allen-Bradley Stratix 5400