Options - Backrest; Options - Sideguard - Sunrise Medical Breezy BasiX2 Directions For Use Manual

Options – Castor adapter
NOTE:
You can change the angle of the castor axle by altering the position
of the castor/rear wheel. This should always be approx. 90°.
ADJUSTING THE CASTOR AXLE ANGLE:
Release the screws (1), pull the castor adaptor outwards, set a 90°
angle and then re-tighten the screws (Fig. 17-18).
Fig. 17
90°
CAUTION!
The castor axle angle must be set the same on both sides (check by
marking).
HORIZONTAL AXLE POSITION
The axle plate can be adjusted
forwards to give greater
manoeuvrability or to the rear to give
greater stability (Fig. 19).
The larger the wheelbase the greater
the security against your wheelchair
tipping over

Options - Backrest

HEIGHT-ADJUSTABLE
BACKREST
The height of the backrest can be set
to 2 or 3 different positions
(depending on the model) (41 cm,
43.5 cm and 46 cm). Release and
remove the bolts (1)+(2), and push
the backrest tube to the desired
position. Tighten up the bolts again
(Fig. 20).
ADJUSTABLE BACKREST
ANGLE
The angle of the backrest can be set
to 6 different positions (-5° forwards,
0°, 5°, 10°, 15° and 20° backwards).
To adjust the angle, remove the
screw (1), set the desired angle and
then re-tighten the screw (Fig. 21).
ADJUSTABLE BACKREST
ANGLE
(7° - 30°)
By pulling both levers together (1),
you can release the backrest and
then move it to the desired position.
On releasing the two levers (1) the
backrest will automatically lock into
place (Fig. 22).
Fig. 18
1
Fig. 19
Fig. 20
1
Fig. 21
1
Fig. 22
1
CAUTION!
• It is recommended that the angle-adjustable backrest is used
in conjunction with the wheelbase extension.
• It is recommended that the angle-adjustable backrest is used
in conjunction with anti-tip tubes (maximum ground clearance
3 - 5 cm).
• We recommend that the angle-adjustable backrest is used in
conjunction with a stabilising bar.
HALF FOLDING BACK
Unfolding the backrest:
To put the backrest in the upright
position, push the handles upwards
and forwards until they lock in.
WARNING!
Keep fingers and other items away
from the folding mechanism when
the backrest is being folded to
prevent injury or damage to
property.
Folding the backrest:
The backrest can be folded to make
storage of the wheelchair easier.
CAUTION!
Do not operate under load as this
may cause lever to break.
To fold the backrest, stand behind
the wheelchair, press the two small
levers (Fig. 23 - 24) positioned on
each side of the backrest (just above the armrests). Fold the
backrest down.
ADJUSTABLE BACK-SLING
The adjustable back-sling
can be adjusted for tension
by using several straps (Fig. 25).
CAUTION!
Do not pull the tension belt too tight,
otherwise this could interfere with the
folding mechanism of the chair.
Options – sideguard
STANDARD SIDEGUARD,
FLIP-UP, REMOVABLE
WITH SHORT OR LONG
ARMRESTS
The sideguard with rounded off front
edges will allow you to get up close to
a table. To flip the armrest up, push
the lever (1), so that the sideguard is
released (Fig. 26 + 27).
The height of the armrest (2) can
be adjusted by fitting the
spacer bracket in various positions.
To do this release the screws, move
the spacer bracket and re-tighten the
screws. The length of the armrest can
be adjusted by releasing the screws
(3), then move the armrest to the
desired position and re-tighten the
screws (Fig. 27).
Fig. 23
Fig. 24
Fig. 25
Fig. 26
2
1
Fig. 27
3
BasiX 15
2