Nice Apollo 4300SW Manual page 23

15 - ACCESSORY INPUTS AND OUTPUTS (CONT.)
15.3 - Communication bus
Figure 18 - COMMUNICATION BUS
OVIEW
Programming and diagnostic unit which connects directly to the gate
controller and is part of the Nice "Opera" control system. The unit can be
used in "stand-alone" mode via its front-panel keypad, or it may be accessed
via a Bluetooth or cellular-enabled PDA, PC, or Smartphone when used
with the O-View Software Suite. This unit, when matched with the OVIEW
Bluetooth or GSM modules, enables remote control and management of the
gate controller. Remote control functions include all programming functions
that are available at the front panel LCD on the control board as well as
software updates.
OVBT: Bluetooth module for OVIEW and the "O-View Software Suite"
application for PC, PDA, or Smartphone for localized wireless control of the
gate controller.
OVBTGSM: GSM module that plugs into the OVIEW and provides cellular
phone access through the "O-View Software Suite" application for PC, PDA,
or Smartphone, for wireless local, national, and international controller of the
gate controller.
O-VIEW Software Suite: Provides desktop or Smartphone level control of
the gate controller. Other benefits include software updates that can be made
wirelessly as new versions of software are made available.
BLUEBUS ACCESSORIES
MOTB: Moon Touch programmable keypad with secure codes (up to 9 digits
per code if required) to control gate opening and closing. Connects to the
2-wire BlueBUS connector with inexpensive unshielded twisted-pair wire.
MOMB: Proximity card access control with capacity for up to 255 MOCARD
or MOCARDP transponder cards. Connects to the 2-wire BlueBUS connector
with inexpensive unshielded twisted-pair wire.
MASTER/SLAVE - ONLY USED IN 24V COMMERCIAL OPERATORS
The gate operator includes a two-pin connector designed to link two
separate gate operators together as a Master/Slave pair. The Master/Slave
configuration is enabled by connecting two gate operators with simple,
unshielded twisted-pair wire (Max.100 ft.). All entrapment sensors, switch
inputs, receiver controls, and outputs must be wired to the gate operator
designated as the "Master". The following procedure outlines the process for
configuring the Master/Slave pair.
Perform the "Learn" process to configure open and close limits with the gate
for each operator. See the "Programming Quick Start" procedures in this
manual for a description of the gate learning process.
On the Master operator, select Function -> Adv. Settings -> Remote Mst. Slv.
Then select On -> Master. The red LED associated with the Master/Slave
connector will illuminate.
On the Slave operator, select Function -> Adv. Settings -> Remote Mst. Slv.
Then select On -> Slave. The red LED associated with the Master/Slave
connector will illuminate.
The Master/Slave pair is now configured. The Slave gate operator will perform
identical open/close/stop functions in tandem with the Master gate operator.
15.4 - Programming the plug-in receiver and remote controls
Plugin Receiver: The SMXI/A 433Plug-In Receiver provides up to 15
channels for specific control of individual gate functions. The receiver includes
built-in programming functions for adding or removing Nice FloR/A wireless
remote controls to/from a gate installation. The following procedures detail the
steps to assign a remote control, add a new remote control, delete a single
remote control, or remove all remote controls from the receiver memory.
Programming 2-Button or 4-Button Remote Control with the NICE
Plug-In Receiver.
These procedures apply to the Nice wireless remote control. These procedures
assign factory default controls automatically to the remote control.
1. Have a functioning Nice 2-button or 4-button remote control with a battery
installed prior to programming the remote control.
2. Press and hold the button on the side of the receiver until the led illuminates
green on the receiver, then release the button.
3. Within 10 seconds, press and hold any key on the remote control until the
led in the receiver blinks green 3 times, indicating that the is programmed
to control the receiver.
4. After the led on the receiver blinks green 3 times, another 10 second interval
is started to program another Nice remote control if desired. Repeat Step 3
to program the additional remote control. Step 3 may be repeated as many
times as necessary to program all available Nice remote controls.
5. Verify that the Nice remote control(s) can control the gate by pressing one
or more buttons individually on the remote control(s).
Wirelessly add new remote control to the Nice Plug-In Receiver
A Nice remote control that has been programmed to control a Nice receiver
may be used to create other Nice remote controls for the same receiver. This
procedure needs to be performed within 10 to 20m (30 to 60 feet) of the Nice
receiver, but the Nice receiver does not need to be physically accessed.
1. Press and hold any button on the un-programmed Nice remote control for
at least 5 seconds, then release the button, taking note of the button that
was pressed.
2. Press the same button on the programmed Nice remote control three
times.
3. Press the same button in step 1 on the un-programmed Nice remote
control and release.
4. It is recommended to test the new copy of the Nice remote control with the
assigned gate controller.
NOTE: This procedure will affect all Nice receivers within radio
range.
Deleting a Single Nice Remote Control from the Nice Plug-In Receiver
Memory
A Nice remote control that has been programmed to control a Nice receiver
may be removed from the Nice receiver memory without affecting other
assigned remote controls. This procedure needs to be performed at the Nice
Plug-In Receiver with the affected Nice remote control.
1. Press and hold the button on the side of the Nice receiver until the led on
the Nice receiver illuminates green and keep the button pressed. The led
will illuminate after approximately 4 seconds.
2. Press and hold any button on the Nice remote control until the led on the
Nice receiver blinks 5 green flashes.
3. Release the button on the side of the Nice receiver.
4. It is recommended to verify that the de-programmed Nice remote control
no longer controls the gate.
21