Installation Instructions; Water Connection; Preparations For Installation; Wall Mounting - Siemens DE1518628 Installation Instructions Manual

Hide thumbs

Advertisement

Table of Contents
Congratulations on purchasing this Siemens appliance. You
have acquired a top-quality product, which will give you a lot
of enjoyment.

Installation instructions

These installation instructions describe a continuous-flow
heater with AquaStop.
Install the appliance as shown in the illustrations. The
illustrations can be found in the centre of the instruction
manual. Observe the instructions in the text.
Installation
I.
Unpacking/Removing the cover
Unpack the appliance and check for transport damage. If
any components are damaged, then do not connect the
appliance.
Check that your appliance contains all components in-
cluded in the scope of delivery: appliance, installation
set with supplementary sheets, installation instructions,
operating instructions.
Please dispose of the packaging and the old appliance in
an environmentally-friendly manner.
When removing the cover, please note the following: The
cover is fastened by a central closure behind the service flap.
II.

Preparations for installation

Important: Only use the supplied installation set.
The supplied water connection nozzles must be installed!
Shut off water supply. The electrical connection (connec-
tion cable) must be disconnected from the power supply.
Unscrew the fuse or switch off the circuit breaker.
Install the water connection nozzles according to the in-
structions on the supplementary sheet.
The electrical connection cable can either be guided in at
the top (X) or bottom (Y).
The rear panel must lie against the cold water connection
nozzle in the position provided for such (Fig. II., 8.).
Pay attention to horizontal and perpendicular alignment.
The appliance must not tilt out more than 1° (2 %) in any
direction!
III.

Wall mounting

The grommet must tightly surround the connection cable.
If it is damaged during mounting, the openings must be
provided with watertight sealing.
The electrical supply terminal can be fitted at the top (X)
or bottom (Y). The sheath of the connection cable must
extend for at least 40 mm into the appliance.
The distance to the wall is variable. You can compensate
for any unevenness of the wall's surface. With a distance
to the wall of 8–16 mm, insert the spacer and install the
extender (Fig. III., 3. – 6.).
The appliance must be mounted securely on the wall. If nec-
essary, attach it at the lower adjustable screws (Fig. III., 7.).
6
en

Water connection

IV.
Before connecting the water, guide the AquaStop connec-
tion pipe into the grommet (Fig. IV., 7.). The grommet
must tightly surround the connection pipe.
Connect the water supply, then open the cold water supply.
When tightening the connections, make sure that the
AquaStop is positioned vertically.
Press the grip surfaces together and pull out the transport
protection attachment to the right (Fig. IV., 10.).
The appliance must be vented. To do so, open the
warm water tap fully and flush out the appliance
thoroughly for 1 minute.
V.
Electrical connection/Mounting
Set the power using the power selector switch before
connecting the wires to the mains connection terminal:
Nominal output power left, reduced output right
(Fig. V., 1.) and the set output marked on the ratings plate.
Screw the wires tightly into the mains connection terminal.
Switch on the safety limiter (Fig. V., 3.).
Install the cover (Fig. V., 4. – 7.).
Installation note
The installation of non plug-in ready appliances must
be undertaken by the respective utility operator or by
a qualified specialist company, who can also assist you
when you are requesting the approval of the utility
company for installation of the appliance.
VI.
Startup
The device is compliant to IEC 61000-3-12.
First start-up
Switch on the fuses.
Setting the temperature.
Initial rinsing: Open the warm water tap fully and allow
water to flow for at least 1 minute. Only then (for safety
reasons) will the appliance begin to heat.
Tip: Should the appliance not start because of a reduced
flow-rate, remove the perlator, shower head or similar before
start and repeat the process.
Explain the operation of the appliance to the user.
Additional information
VII.
If the appliance does not have sufficient water flow due
to low water line pressure in your domestic plumbing sys-
tem, remove the flow-rate limiter (Fig. VII., 1. – 3.).
Priority circuit for the combination with electrical storage
heaters:
For operation with a priority circuit, a special load shed-
ding relay BZ 45L21 (special accessory) is required. Other
existing load shedding relays, with the exception of elec-
tronic load shedding relays, may malfunction (Fig. VII.,
Wiring diagram).
The control electronics must be coded when operated
with a load shedding relay. Remove the keying nose on
the electronics (Fig. VII., 4.).

Advertisement

Table of Contents
loading

This manual is also suitable for:

De2427628De2124628