Table of Contents
Advertisement
Quick Links
USER MANUAL
SPEED DOME CAMERA SD-Dxxx Series II
Page: 1
Page: 1
SERIES SD-Dxx
Cameras
High Speed D ome AHD /
analog
INTRODUCTION
cameras
The
Fully remote controllable. They allow an operator to rotate the camera in all directions and
zoom in pleasure on the scenes of most interest.
Can
automatic pre-programmed according to specific monitoring requirements.
What is PTZ
The cameras controlled remotely are also defined PTZ, which stands for PAN / TILT /
ZOOM. PAN is the movement in horizontal, TILT movement in vertical and ZOOM control of
the lens focal length.
Controlling the speed dome
The speed-dome cameras are controlled with special console
of
DSE digital video recorders. Digital video recorders also allow control of remote cameras via
network or Internet, using both PC and smart phone or tablet. The command of the cameras
is carried out on twisted pair with Pelco D Protocol today
consolidated in the sector.
WWW.DSE.EU
speed domes
I'm
also perform movements
command
or
through
cameras
the
standard
Advertisement
Table of Contents
Related Manuals for DSE SD-D Series
Summary of Contents for DSE SD-D Series
-
Page 1: User Manual
DSE digital video recorders. Digital video recorders also allow control of remote cameras via network or Internet, using both PC and smart phone or tablet. The command of the cameras is carried out on twisted pair with Pelco D Protocol today standard consolidated in the sector. -
Page 2: Main Specifications
USER MANUAL SPEED DOME CAMERA SD-Dxxx Series II Page: 2 Page: 2 MAIN SPECIFICATIONS www.dseitalia.it/dati_speed-dome.htm WWW.DSE.EU... -
Page 3: Installation Of Camera
0.5 mm, while if it is From a Speed D ome SD-D series camera protrudes a cable fitted with the following necessary to reach considerable distances (max. 1200 m.) Should be used upper sections of connections: 1 mm or even 2.5 mm. -
Page 4: Set Protocol
The camera is set with address 1 Factory. E 'can set any address between 1 and 255 as long as different for each camera. On the camera motherboard there are 2 blocks of microswitches: one from 4:01 to 8 switches. WWW.DSE.EU... - Page 5 USER MANUAL SPEED DOME CAMERA SD-Dxxx Series II Page: 5 Page: 5 ADDRESS SW.1 sw.2 sw.3 sw.4 sw.5 sw.6 sw.7 Sw.8 WWW.DSE.EU...
- Page 6 USER MANUAL SPEED DOME CAMERA SD-Dxxx Series II Page: 6 Page: 6 ..WWW.DSE.EU...
-
Page 7: Ceiling Mount
Cameras 4 in 1 AHD / CVI / TVI and CVBS The models 4 in 1 (RE ---- 4) are able to support all analog video formats available today, including those used by other manufacturers. In addition to traditional analog CVBS video and the format described AHD WWW.DSE.EU... -
Page 8: Wall Mounting
Connect the camera and fasten it to the bracket with the supplied screws. Fasten the wall bracket by plugs, taking care to leave the cable outlet at the center between the fixing holes. Other types of bracket are optionally available. WWW.DSE.EU... -
Page 9: Basic Operations
The controls of the opening IRIS +/- Aperture are not normally below. The initiation of these movements is carried out with the organ of control commands allowed by the cameras factory settings. or by using the system presets. WWW.DSE.EU... -
Page 10: System Preset
Recalling the preset 64, the main camera position (IDLE see above) will be scanning the panoramic 360 ° CALL Opens OSD room Recalling the preset 70 opens the menu screen (OSD) for the configuration of the camera module TOUR MANAGEMENT (CRUISE) WWW.DSE.EU... - Page 11 The panning is set using preset listed above. These presets set the scan speed: 65 = 3 ° / sec 66 = between limit switch 360 °) 6 ° / sec 67 = 9 ° / 68 sec = 15 ° / 69 sec = 40 ° / sec WWW.DSE.EU...
- Page 12 USER MANUAL SPEED DOME CAMERA SD-Dxxx Series II Page: 12 Page: 12 WWW.DSE.EU...
- Page 13 To move within the general OSD menu using the joystick or navigation arrows. To select a menu item or exit using the IRIS + button (ENTER) and IRIS - (EXIT) Access to the OSD menu of the camera module only WWW.DSE.EU...
-
Page 14: System Info
If after set a software address is changed the position of the dip-switch board room, the camera will resume the address hardware. This way you avoid losing the communication with the camera because of WWW.DSE.EU... -
Page 15: Special Function
Preset Function This section allows you to set the camera presets via the programming menu, although this is also possible via the controls keyboard described such as from already WWW.DSE.EU... -
Page 16: Display Information
System default This section allows you to restore the factory configuration. For each program you set the start time and end time, then you choose the automatic function to be executed (preset, tour, etc.) and the number of the function. WWW.DSE.EU... - Page 17 Page: 17 Page: 17 OSD Camera set-up This section contains the settings of the camera module which has its own independent configuration from the mechanical movement of the dome. The camera module options are described in the next chapter. WWW.DSE.EU...
- Page 18 ADDRESS DISP - Not available • D & N - Sets the operation day night AUTO, COLOR, B / W, CDS (sensor) • D & N LV - passage Threshold Day-Night • N & D LV - Threshold crossing Night-Day WWW.DSE.EU...
- Page 19 F-RANGE - Adjusts the depth of field of the focus of the autofocus function • ZDISP-POS - Rule the position of the superimpose zoom value (RD = Bottom right, LD = Bottom left, LU = top left, RU = Upper Right • RESET - Restores the factory settings • SAVE EXIT WWW.DSE.EU...
- Page 20 DAY & NIGHT - Defines the day / night changeover mode: AGC (automatic based on the image brightness) CDS (automatic based on sensor) COLOR (always color image) BK (still picture B / N • FOCUS - Defines the management of fire (AUTO / MANUAL) • BAUD RATE - not editable WWW.DSE.EU...
Need help?
Do you have a question about the SD-D Series and is the answer not in the manual?
Questions and answers