Table of Contents
Advertisement
Quick Links
AIR ROUTER - 1/4"
SET Up And OpERATIng InSTRUcTIOnS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
distributed exclusively by Harbor Freight Tools
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MAnUAl.
©
Copyright
2008 by Harbor Freight Tools
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
Model
3491 Mission Oaks Blvd., Camarillo, CA 93011
97728
®
. All rights reserved. No portion of this
®
.
Advertisement
Table of Contents
Related Manuals for Harbor Freight Tools Central Pneumatic 97728
Summary of Contents for Harbor Freight Tools Central Pneumatic 97728
- Page 1 . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions or replacement parts, please call 1-800-444-3353.
-
Page 2: Safety Alert Symbol And Signal Words
SAVE THIS MAnUAl nOTIcE is used to address practices Keep this manual for the safety not related to personal injury. warnings and precautions, assembly, cAUTIOn, without operating, inspection, maintenance and the safety alert cleaning procedures. Write the product’s symbol, is used to address serial number in the back of the manual near practices not related to the assembly diagram (or month and year of... -
Page 3: Personal Safety
tool. Distractions may result in the conditions. Wear heavy-duty work loss of control of the tool. gloves during use. personal safety Always wear eye protection. Wear ANSI- Stay alert. Watch what you are approved safety goggles. doing and use common sense Always wear hearing when operating the tool. -
Page 4: Air Source
Service do not use the tool if the Trigger does not turn the tool on or off. Tool service must be performed Any tool that cannot be controlled only by qualified repair personnel. with the Trigger (3) is dangerous and must be repaired. -
Page 5: Symbols And Specific Safety Instructions
SYMbOlS And factors which cannot be built into this product, but must be supplied by the SpEcIFIc SAFETY operator. InSTRUcTIOnS WARnIng: Some dust created by power sanding, sawing, grinding, Symbol Definitions drilling, and other construction activities, contains chemicals property or statement known [to the State of California] to No-load speed cause cancer, birth defects or other... -
Page 6: Vibration Precautions
Refer to the manual for the air Wear suitable gloves to reduce the compressor used to power this tool. vibration effects on the user. Install an in-line shutoff valve to allow Use tools with the lowest vibration immediate control over the air supply when there is a choice between in an emergency, even if a hose is different processes. -
Page 7: Components And Controls
When unpacking, check to make sure FIgURE b that the item is intact and undamaged. If 3/4” any parts are missing or broken, please SpAnnER WREncH call Harbor Freight Tools at the number (34) shown throughout the manual as soon as 9/16”” SpAnnER possible. WREncH (35) •... -
Page 8: Air Supply
• Place the Housing Cap (30) over note: If an automatic oiler system is not the Housing (1) and turn clockwise used, add a few drops of Pneumatic to tighten securely. At least two full Tool Oil dAIlY into the tool’s male threads of the Router Base should Quick Coupler before operation. -
Page 9: General Operating Instructions
but the output will not exceed the allow access by children or pets to tool’s maximum air pressure at any prevent injury and distraction. time. Adjust the pressure gradually, Route the air hose along a safe while checking the air output gauge route to reach the work area without until the required pressure valve is creating a tripping hazard or exposing... -
Page 10: Maintenance Instructions
(32) should be smooth and free of cloth, and apply a thin coat of tool oil. debris. Then remove the bit and store the tool indoors out of children’s reach Place the Router Base (32) of the Air and other unauthorized people. Router on the work piece, but avoid contacting the Router Bit with the MAInTEnAncE... - Page 11 TO pREVEnT ExplOSIOn: lubricate the tool only with specified lubricants. lubricate the air inlet using only pneumatic tool oil. lubricate the internal mechanism using only white lithium grease. Other lubricants may damage the mechanism and may be highly flammable, causing an explosion.
-
Page 12: Troubleshooting
Troubleshooting problem possible causes likely Solutions Decreased output. Not enough air pressure and/ Check for loose connections and make sure or air flow. that air supply is providing enough air flow (CFM) at required pressure (PSI) to the tool’s air inlet. do not exceed maximum air pressure. -
Page 13: Parts List & Assembly Diagram
pARTS lIST & ASSEMblY dIAgRAM SKU 97728 For technical questions, please call 1-800-444-3353. Page 13... -
Page 14: Limited 1-Year Warranty
1 YEAR WARRAnTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of one year from the date of purchase (90 days if used by a professional contractor or if used as rental equipment).