Table of Contents
Advertisement
Quick Links
Features
Ultra Compact size (25.0 x 20.0mm)
Built In Front End Module to boost Output power upto +20dBm with Integrated
LNA for increased Sensitivity
MCU less Tranceiver module with SPI interface
High RX sensitivity (-104dBm)
Outperforming link budget (up to +124dB)
Up to +20.5dBm output power
Very low power consumption:
7.5mA in RX mode
157mA in TX mode
0.7µA in sleep mode
Internal Clock Output
Preassigned Atmel
Capability to use MAC address into the onboard EEPROM
®
IEEE
2.4GHz ISM band
Rapid design-in with built-in Chip Antenna
RF Test point using MS-147 RF connector
Small physical footprint and low profile for optimum fit in very small application
boards
Mesh networking capability
Easy-to-use low cost development kit
Single source of support for HW and SW
Worldwide license-free operation
Note:
1. MCU is in active state with 3V Supply, CPU clock @ 16MHz, RX RPC enabled (for RX current),
PHY_TX_PWR=0x0 (for TX current), All digital outputs pulled high.
2. Controller Sleep Mode – SLEEP_MODE_PWR_DOWN
Note:
ZIGBIT 2.4GHZ WIRELESS MODULES
(1)
(1)
(2)
®
MAC address that can be used on end product
802.15.4 compliant Transceiver
ATZB-RF-233-1-C
DATASHEET
42192AWIRELESS11/2013
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Atmel ZIGBIT ATZB-RF-233-1-C
Summary of Contents for Atmel ZIGBIT ATZB-RF-233-1-C
- Page 1 157mA in TX mode 0.7µA in sleep mode Internal Clock Output ® Preassigned Atmel MAC address that can be used on end product Capability to use MAC address into the onboard EEPROM ® IEEE 802.15.4 compliant Transceiver ...
-
Page 2: Table Of Contents
Table of Contents 1. Introduction ..................3 Summary ......................3 Applications ....................... 3 Abbreviations and Acronyms ................3 Related Documents ................... 5 2. ZigBit Module Overview ..............6 Overview ......................6 3. Specification..................8 Electrical Characteristics ................... 8 3.1.1 Absolute Maximum Ratings ..............8 3.1.2 Power Supply .................. -
Page 3: Introduction
ZigBit reach a very high Link budget of upto +124dB. Based on the innovative mixed-signal hardware platform from Atmel, this module uses the AT86RF233 [4] /2.4GHz ISM band Transceiver with the FEM on a very compact Module design that provides the customer to integrate the module to any of the recommended Atmel’s Microcontrollers that the application fits. - Page 4 ETSI European Telecommunications Standards Institute Federal Communications Commission Front End Module GPIO General Purpose Input/Output High Frequency HVAC Heating, Ventilating, and Air Conditioning Hardware Industry Canada Inter-Integrated Circuit IEEE Institute of Electrical and Electronics Engineers Interrupt Request Industrial, Scientific and Medical radio band JTAG Digital interface for debugging of embedded device, also known as IEEE 1149.1 standard interface...
-
Page 5: Related Documents
[2] IEEE Std 802.15.4-2003 IEEE Standard for Information technology - Part 15.4 Wireless Medium Access Control (MAC) and Physical Layer (PHY) Specifications for Low-Rate Wireless Personal Area Networks (LR-WPANs) [3] ZigBee Specification. ZigBee Document 053474r17, October 19, 2007 [4] AT86RF233 Datasheet in http://www.atmel.com/devices/AT86RF233.aspx?tab=documents ATZB-RF-233-1-C ZigBit 2.4GHz Wireless Modules [DATASHEET] 42192AWIRELESS11/2013... -
Page 6: Zigbit Module Overview
The ATZB-RF-233-1-C ZigBit is a compact, low-power, high sensitivity IEEE 802.15.4/ZigBee OEM module with an integrated FEM built-in. Based on a solid combination of the latest Atmel MCU Wireless hardware platform, 2.4GHz ISM band transceiver and Atmel Studio Wireless Composer - the ZigBit offers an unmatched combination of superior radio performance, ultra-low power consumption and exceptional ease of integration. - Page 7 2-layer PCB with a minimum of required external connection. The ZigBit Module Evaluation kit containing the ZigBit Extension board for the Atmel Xplained PRO HW Evaluation platform can be used to develop FW using the Atmel Studio and evaluate using the Wireless Composer. Compared to a custom RF/MCU solution, a module-based solution offers considerable savings in development time and NRE cost per unit during the HW/FW design, prototyping, and mass production phases of product development.
-
Page 8: Specification
Specification Electrical Characteristics 3.1.1 Absolute Maximum Ratings (1)(2) Table 3-1. Absolute Maximum Ratings Parameter Minimum Maximum Voltage on any pin, except RESET with respect to ground -0.3V 3.6V (V DD max Input RF level +10dBm Current into Vcc pins 200mA Absolute Maximum Ratings are the values beyond which damage to the device may occur. -
Page 9: Rf Characteristics
3.1.3 RF Characteristics Table 3-3. RF Characteristics Parameter Condition Range Unit Frequency band 2.4000 to 2.4835 Numbers of channels (North American) Channel spacing Transmitter output power Adjusted in 7 steps +2.6 to + 19.9 Receiver sensitivity PER = 1% -105 On-air data rate 250, upto 2000 Kbps... -
Page 10: Physical/Environmental Characteristics And Outline
+21.3 +21.3 +21.3 +21.3 +21.3 +21.2 +21.1 +13.0 0xE or less Restricted - Do not use in North America and Canada Restricted – Refer Note 2 for Europe Physical/Environmental Characteristics and Outline Table 3-6. Physical characteristics. Parameters Value Comments Size 25.0 x 20.0mm Operating temperature range -40°C to +85°C... -
Page 11: Antenna Orientation Recommendation
Pin Out Function descriptions TWI- EEPROM TWI- EEPROM FEM_CPS Front end module select for RF_TX_RX CLKM Master Clock out put Interrupt request signal output DVSS Digital Ground DVSS Digital Ground Antenna Orientation Recommendation The Antenna in this module is designed to provide the best possible LoS range in the direction indicated in this illustration. - Page 12 Figure 3-1. ATZB-RF-233-1-C Dimensions Figure 3-2. ATZB-RF-233-1-C Pinout ATZB-RF-233-1-C ZigBit 2.4GHz Wireless Modules [DATASHEET] 42192AWIRELESS11/2013...
- Page 13 Figure 3-3. ATZB-RF-233-1-C Foot Pring Dimensions Figure 3-4. ATZB-RF-233-1-C Mounting Information The ZigBit’s location and orientation on the carrier board is illustrated in the above PCB Land pattern and Mounting information drawing. The Recommended placement of ZigBit on Carrier Board needs to be accurately followed to ensure performance on the end application ATZB-RF-233-1-C ZigBit 2.4GHz Wireless Modules [DATASHEET] 42192AWIRELESS11/2013...
-
Page 14: Soldering Profile
Soldering Profile The J-STD-020C-compliant soldering profile is recommended according to Table 3-8. Table 3-8. Soldering profile Profile feature Green package Average ramp-up rate (217°C to peak) 3°C/s max Preheat temperature 175°C ±25°C 180s max Temperature maintained above 217°C 60s to 150s Time within 5°C of actual peak temperature 20s to 40s Peak temperature range... -
Page 15: Handling Instructions
Handling Instructions The ZigBit Modules are fixed with an EMI Shield to ensure compliance to Emission and Immunity rules. This shield is galvanic and NOT air tight. So cleaning of the module with IPA / other similar agents is not advised. Humidity protection coating (conformal) will cause deviated RF behavior and coating material being trapped inside EMI Shield. -
Page 16: Agency Certifications
Agency Certifications United States (FCC) This equipment complies with Part 15 of the FCC rules and regulations. To fulfill FCC Certification requirements, an OEM manufacturer must comply with the following regulations: The ATZB-RF-233-1-C modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. -
Page 17: Canada (Ic)
IMPORTANT: The 'CE' marking must be affixed to a visible location on the OEM product. The CE mark shall consist of the initials "CE" taking the following form: The CE marking must have a height of at least 5mm except where this is not possible on account of the nature of the apparatus. -
Page 18: Revision History
Revision History Doc. Rev. Date Comments 42192A 11/2013 Initial revision. ATZB-RF-233-1-C ZigBit 2.4GHz Wireless Modules [DATASHEET] 42192AWIRELESS11/2013... - Page 19 Corporation or its subsidiaries. Other terms and product names may be trademarks of others. Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products.
Need help?
Do you have a question about the ZIGBIT ATZB-RF-233-1-C and is the answer not in the manual?
Questions and answers