Table of Contents
Advertisement
Quick Links
Description
The ATSAMR21B18-MZ210PA is a 19.7mm x 16.3mm wireless module. It
integrates an ATSAMR21E18 IC together with a serial data FLASH. The design
allows a variety of mounting positions with SMT as well as TH mounting. The
extended temperature range with operation up to 125°C is a distinguishing feature.
Features
ATSAMR21 Single-chip ARM® Cortex®-M0+ based 32-bit Microcontroller with
Low Power 2.4GHz Transceiver for IEEE 802.15.4 and ZigBee Applications with
256KB Flash and 16 I/O's
–
Max. operating freq. 48 MHz
–
128-bit AES crypto engine
–
32-bit MAC symbol counter
–
Temperature sensor
–
Automatic transmission modes
MX25L2006EZUK-12G 2-Mbit DataFlash
Lowest cost RF front end design with PCB antenna
FCC / ETSI compliant harmonic filter
Single 2.7V - 3.6V supply
Extended industrial temperature range -40°C to 125°C
Easy access 2mm pin header with several alternative functions
–
5 GPIO
–
1 analog input (12-bit, 350ksps Analog-to-Digital Converter)
–
4 PWM outputs
–
2
TWI (I
C up to 3.4MHz)
–
SPI
–
UART
High precision 16MHz crystal oscillator
Fulfills FCC limits for wearable devices
ATSAMR21B18-MZ210PA
ATSAMR21 Smart Connect Module
PRELIMINARY DATASHEET
Atmel-42486C-ATSAMR21B18-MZ210PA_Datasheet_03/2016
Advertisement
Table of Contents
Related Manuals for Atmel ATSAMR21
Summary of Contents for Atmel ATSAMR21
-
Page 1: Description
SMT as well as TH mounting. The extended temperature range with operation up to 125°C is a distinguishing feature. Features ATSAMR21 Single-chip ARM® Cortex®-M0+ based 32-bit Microcontroller with Low Power 2.4GHz Transceiver for IEEE 802.15.4 and ZigBee Applications with 256KB Flash and 16 I/O’s –... -
Page 2: Table Of Contents
Boot loader ........................ 13 Radio Certification ..................... 14 United States (FCC) ..........................14 Europe (ETSI) ............................. 14 Industry Canada (IC) Compliance statements ..................15 Ordering Information ....................16 References ......................... 17 10 Revision History ......................17 ATSAMR21B18-MZ210PA [PRELIMINARY DATASHEET] Atmel-42486C-ATSAMR21B18-MZ210PA_Datasheet_03/2016... -
Page 3: Integrated Devices And Block Diagram
There are two UART interfaces available for external use. SERCOM2 is available at test points for debug use while SERCOM1 is available at connector X1 for application use. The test points for SERCOM2 are duplicated on the PCB top layer and on the bottom layer. See 0 for detailed information. ATSAMR21B18-MZ210PA [PRELIMINARY DATASHEET] Atmel-42486C-ATSAMR21B18-MZ210PA_Datasheet_03/2016... -
Page 4: Rf Front End
The integrated antenna is the cause of a number of design constraints for the base board. Please regard the drawings and suggestions in section 2.3 when designing the base board. The same section does also contain more information about the ground design. ATSAMR21B18-MZ210PA [PRELIMINARY DATASHEET] Atmel-42486C-ATSAMR21B18-MZ210PA_Datasheet_03/2016... -
Page 5: Mechanical Description
The module length is 19.7mm by design. The edges are created in an automated milling process and have a tolerance of +/- 0.1mm. The module width is 16.3mm by design. The edges are created by separation of a V-cut PCB and have a tolerance of +0.2mm and – 0.1mm. ATSAMR21B18-MZ210PA [PRELIMINARY DATASHEET] Atmel-42486C-ATSAMR21B18-MZ210PA_Datasheet_03/2016... -
Page 6: Footprint Recommendation
The mounting distance in between the module and the base board shall be in between 1mm and 2mm. For lower distances the design rules for the SMT mounting according to Figure 2-3 will apply. ATSAMR21B18-MZ210PA [PRELIMINARY DATASHEET] Atmel-42486C-ATSAMR21B18-MZ210PA_Datasheet_03/2016... -
Page 7: Surface Solder Mounting
The SMT pads in the base board shall exceed the module outline at least by 0.45mm to achieve a controlled solder result. Figure 2-3. Base board design for SMT module mounting ATSAMR21B18-MZ210PA [PRELIMINARY DATASHEET] Atmel-42486C-ATSAMR21B18-MZ210PA_Datasheet_03/2016... -
Page 8: Module Pin Assignment
The module pin assignment is shown in Table 3-1 Table 3-1. The Column “uC pin” is a reference to the ATSAMR21 datasheet (SAMR21). The column “Pin function” shows a selection of alternative IO functions. Please refer to the ATSAMR21 datasheet for the complete IO multiplexer description. -
Page 9: Test Points
UART Tx, GPIO PA15 UART Rx, GPIO Table 3-2. Top layer test points Please refer to the ATSAMR21 datasheet for the complete IO multiplexer description for these port pins. Figure 3-1. Top layer test point locations 3.2.2 Bottom layer test points The bottom layer test points allow the programming interface access as well as the same UART connection as the top layer test points. - Page 10 When the module needs to be operated without a base board e.g. for debugging two 40mm wires can be soldered to the antenna ground pins as a makeshift ground plane. Figure 3-3. Makeshift antenna reference ground for standalone operation ATSAMR21B18-MZ210PA [PRELIMINARY DATASHEET] Atmel-42486C-ATSAMR21B18-MZ210PA_Datasheet_03/2016...
-
Page 11: Electrical Characteristics
Unit Storage Temperature +125 °C STOR Pin voltage with Vcc+0.3V respect to GND and -0.3V Module IO’s routed to ATSAMR21 ESD robustness Human Body Model Charged Device Model Input RF level Level at ATSAMR21 pins Recommended Operating Conditions Symbol Parameter Condition Min. -
Page 12: Module Performance Data
T = 25°C NV memory XTAL_TRIM setting Reference crystal drift over tempera- -40°C <T < +125°C Ref_T ture rx level frequency distribution Rx ED level Figure 4-1. Distribution of average rx levels observed in 50 PER tests with 1000 frames each. ATSAMR21B18-MZ210PA [PRELIMINARY DATASHEET] Atmel-42486C-ATSAMR21B18-MZ210PA_Datasheet_03/2016... -
Page 13: Nv Memory Information
NV Memory Information The ATSAMR21 provides a user readable NV memory space called user row in the data sheet. The base address for the application is 0x804008. Table 5-1Error! Reference source not found. shows the implemented data structure. Addr. offset... -
Page 14: Radio Certification
The CE marking must have a height of at least 5 mm except where this is not possible on account of the nature of the apparatus. The CE marking must be affixed visibly, legibly, and indelibly. ATSAMR21B18-MZ210PA [PRELIMINARY DATASHEET] Atmel-42486C-ATSAMR21B18-MZ210PA_Datasheet_03/2016... -
Page 15: Industry Canada (Ic) Compliance Statements
à l'intérieur d'un autre appareil, l'appareil doit afficher l'étiquette sur le module de référence ci-joint. Dans ce cas, le produit final doit être étiqueté dans un endroit visible par le texte suivant: “Contains Transmitter Module IC: 20266-ATSAMZ210PA0” “Contains IC: 20266-ATSAMZ210PA0” ATSAMR21B18-MZ210PA [PRELIMINARY DATASHEET] Atmel-42486C-ATSAMR21B18-MZ210PA_Datasheet_03/2016... -
Page 16: Ordering Information
Ordering Information Module Type Packaging Ordering Code Package Operational Range Industrial 16.3mm x Tape&Reel ATSAMR21B18-MZ210PA-T ATSAMR21B18-MZ210PA 19.7mm (-40°C to +85°C) Note: 1. MOQ is a reel with 200 modules. ATSAMR21B18-MZ210PA [PRELIMINARY DATASHEET] Atmel-42486C-ATSAMR21B18-MZ210PA_Datasheet_03/2016... -
Page 17: References
References [1 ] Macronix. (n.d.). Macronix International Co., Ltd. Retrieved from MX25L2006E (K-Grade) Datasheet: http://www.macronix.com [2] Atmel SAM R21. (n.d.). www.atmel.com. Retrieved from http://www.atmel.com/Images/Atmel-42223-SAM-R21_Datasheet.pdf Revision History Doc Rev. Date Comments The product now fulfills the FCC limits for wearable devices. Feature list updated. - Page 18 DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, b y estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODU CTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON -INFRINGEMENT.