Download Print this page

HES K100-620 Aperio Series Installation Instructions Manual

Cabinet lock

Advertisement

Quick Links

Aperio Cabinet Lock Components
Antenna/Reader
Strike Plate
Quick Installation Summary
1. Mark
4. Install
Part Number 3080006.001, Rev. D
K100-620 Aperio
Cabinet Lock Series
Installation Instructions
Installation Hardware
Lock
Body
Machine
screw with
Mounting
washer
Templates
1X
1X
1X
2. Drill
©2012, HES, Inc.
HES, Inc.
Phoenix, AZ
1.800.626.7590
www.hesinnovations.com
Card Reader Template
Key Override Paddle
1X
2-56x3/8"
6 x 1/2"
0-80x½"
2X
3X
1X
5/16"
1X
1"
2X
Battery
1X
3. Configure
5. Connect
Aperio Hub
Battery Cover
Washer
1X
1X
Shaft Extension
1X
2-56x1-1/4"
1X
6-32 screws
1-1/4"
1-5/8"
1-3/4"
2X
1X
1-7/8"
2-1/2"
2X
2X
2X
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the K100-620 Aperio Series and is the answer not in the manual?

Questions and answers

Summary of Contents for HES K100-620 Aperio Series

  • Page 1 Mounting 2-56x1-1/4” washer Templates 6-32 screws Strike Plate 5/16” 1” 1-1/4” 1-5/8” Battery 1-3/4” 1-7/8” 2-1/2” Quick Installation Summary 1. Mark 2. Drill 3. Configure 4. Install 5. Connect Aperio Hub Part Number 3080006.001, Rev. D ©2012, HES, Inc.
  • Page 2 2c. Next, transfer this centerline to the inside of the cabinet or the second door on a double-door cabinet. 2a. Mark cabinet at centerline notch Latch centerline notch 2c. Transfer latch centerline 2b. Draw latch centerline Part Number 3080006.001, Rev. D ©2012, HES, Inc.
  • Page 3 5b. Drill only one hole of the three override function. For example, in the door handing shown here, possible antenna/reader orientations manual override cannot be used in orientation “A”, but it can be used in orientations “B” and “C”. Part Number 3080006.001, Rev. D ©2012, HES, Inc.
  • Page 4 8b. Calculate the distance from the lock instructions. features based on the image to the right. 8c. Drill a hole in the door based on the Key Override cam lock installation instructions. Paddle Latch centerline Part Number 3080006.001, Rev. D ©2012, HES, Inc.
  • Page 5 10b. Using two 6-32 lock mount screws (see table 2 for length), attach the lock to the antenna/reader. Tighten the screws. Thread the cable through the hole in the lock. 10a. Place the lock and thread cable. 10b. Attach the lock to the antenna reader. Part Number 3080006.001, Rev. D ©2012, HES, Inc.
  • Page 6 13a. Peel off the protective layer of the Strike Plate Template and align it to both the latch centerline and the edge of cabinet. 13b. Drill two pilot holes as shown. 13c. Remove the template. Part Number 3080006.001, Rev. D ©2012, HES, Inc.
  • Page 7 16c. After adjusting, insert and tighten the lock-down screw on the strike plate. lock-down screw. Note: Do not install the lock- down screw until the strike plate is 16.a-b. correctly Place the strike plate adjusted. and adjust. Part Number 3080006.001, Rev. D ©2012, HES, Inc.
  • Page 8: Led Indications

    17b. Lock maintenance LED indication Some special LED indication schemes are used during lock maintenance actions: Five yellow flashes Enter configuration mode (.125 seconds each) Fig. Lock Normal operation LED indication Part Number 3080006.001, Rev. D ©2012, HES, Inc.
  • Page 9 Secure area memory corrupt 0x0400 Secure area sensor or motor error 0x0800 Radio modem communication error 0x1000 Radio modem memory corrupt 0x2000 Radio modem configuration error 0x4000 Radio modem RF circuit error 0x8000 Part Number 3080006.001, Rev. D ©2012, HES, Inc.
  • Page 10 Son fonctionnement est souimes aux deux conditions suivantes: (1) cet appareil ne peut causer d’interférences, et (2) cet appareil doit accepter toute interference, y compris des interférences qui peuvent provoquer un fonctionnement indésirable du périphérique. Part Number 3080006.001, Rev. D ©2012, HES, Inc.