Table of Contents
Advertisement
2.1 SAFETY PRECAUTIONS
Do not attempt to operate the machine until the safety
precautions and operating instructions in this manual are
read completely and are thoroughly understood.
Take notice of all warning labels on the machine. The la-
bels have been put there to help maintain a safe working
environment. The labels have been designed to withstand
washing and cleaning. All labels must remain legible for
the life of the machine. Labels should be checked periodi-
cally to be sure they can be recognized as warning labels.
If danger, warning or caution labels are needed, indicate
the part number, type of label, location of label, and quantity
required along with your address and mail to:
STOELTING
ATTENTION: Customer Service
502 Hwy. 67
Kiel, Wisconsin 53042
2.2 RECEIVING THE CUSTARD MACHINE
A.
Upon arrival, check the entire machine for any
damage that may have occurred during transit.
With the method of packaging used, the machine
should arrive in excellent condition. The carrier
is responsible for all damage in transit, whether
visible or concealed. Do not pay the freight bill
until the machine has been checked for damage.
Have the carrier note any visible damage on the
freight bill. If concealed damage or a shortage is
found later, advise the carrier within 10 days and
request inspection. The customer must place a
claim for damages and/or shortages in shipment
with the carrier. Stoelting cannot make any claims
against the carrier.
B.
Remove the top of the crate using a hammer or
pry bar.
C.
Remove the eight lag bolts from the machine
using a 1/2" ratchet. Remove the front and rear
crate walls.
D.
Remove the four lag bolts located inside the left
and right crate walls using 1/2" ratchet. Remove
the left and right crate walls.
E.
Remove the plastic wrapping on the machine.
Remove the lower front and back panel on the
machine.
F.
Remove the four lag bolts located inside machine
on the frame with a 9/16" ratchet. Remove the
two lag bolts that hold the skid together with a
9/16" socket.
Owner's Manual #513666
SECTION 2
INSTALLATION INSTRUCTIONS
3
G.
If the machine has the shipping casters or if it is
water-cooled, the casters will be in a box located
in the hopper pan. A set of casters includes two
casters with locks and two casters without locks.
Screw the casters into the threaded holes and
tighten them using a pair of channel locks. After
installing the casters, knock out bottom 4" x 4" of
the machine skid.
If the machine does not come with casters, install
the stainless steel legs. The legs are located in the
hopper pan on top of the machine. After installing
the legs, use a pallet jack to move machine into
place.
H.
Put front and back panels on the machine.
2.3 MACHINE INSTALLATION
The following instructions are intended for a qualifi ed
electrician/refrigeration specialist. Do not attempt these
procedures unless you are qualifi ed.
CAUTION
Installation MUST be completed by a qualifi ed
electrician/refrigeration specialist
Incorrect installation may cause personal injury,
severe damage to the machine and will void fac-
tory warranty.
A. RUNNING LINE SETS
If the machine is water-cooled, proceed to "B. Run-
ning Electrical Connections".
Line sets are not supplied with the machine.
The lines sets can be installed prior to receiving the
custard machine.
1
An air-cooled machine requires a remote
condensing unit and line set for each freezing
cylinder. The line sets must be 3/8" for the liquid
line and 5/8" for the suction line. When running
the line sets, each 10' of vertical rise, install a
p-trap in the suction line. For every horizontal
line set run, pitch the suction line towards the
compressor to assist with oil returning back to
the compressor.
2
After the line set is installed, perform a thorough
leak test. Malfunctions of the equipment due
to leaks in the line set are not covered by the
Stoelting/Ross warranty.
NOTE
NOTE
M202B Model Machines
Advertisement
Table of Contents
Troubleshooting
