Advertisement
Quick Links
Advertisement
Related Manuals for CHIEF OXCM1U
Summary of Contents for CHIEF OXCM1U
- Page 1 I N S T A L L A T I O N I N S T R U C T I O N S Extra Large Outdoor Floor/Ceiling Mount Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description OXCM1U...
-
Page 2: Important Safety Instructions
WARNING: Use this mounting system with other outdoor ACCESSORY: AN ACCESSORY is the secondary Chief product which is attached to a primary Chief product, and may products only. have a component attached or setting on it. WARNING: Always use two people or a mechanical lifting... - Page 3 Installation Instructions OXCM1U DIMENSIONS +5°AND -15° HOLE LOCKOUT 0° HOLE LOCKOUT +7.6° HOLE LOCKOUT -10° HOLE -5° AND -20° LOCKOUT HOLE LOCKOUT 2.48 63.0 - 10° 1.91 48.4 DIMENSIONS: INCHES [MILLIMETERS]...
- Page 4 OXCM1U Installation Instructions LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación...
-
Page 5: Tools Required For Installation
Installation Instructions OXCM1U TOOLS REQUIRED FOR INSTALLATION 5/32” (included) 1/2” 9/16” 3/8" PARTS [Interface Bracket Hardware Kit] [Interface Lockout Bag] - (2) - (qty. per bag) B (4) A (4) C (4) D (4) M6x25mm M8x20mm M8x30mm M6x16mm F (4) -
Page 6: Installation
OXCM1U Installation Instructions INSTALLATION (to floor) IMPORTANT ! : The following procedure assumes that: (U) x 2 • Two UL Listed ODAC Series Floor/Ceiling Columns (not included) has been properly installed following instructions provided with plate and pipe. Attaching Mount to ODAC Series Column... - Page 7 Installation Instructions OXCM1U Slide X-large rail (JJ) onto one of two assemblies (H) Use four 1/4-14 x 3/4" hex flange bolts (AA) to secure two attached to column. (See Figure 4) side covers (GG) to ends of X-large rail (JJ). (See Figure 7)
- Page 8 OXCM1U Installation Instructions Use two 1/4-20 x 5/8" cap screws (Z) and two 1/4" washers (DD) to secure center wind shield (K) to sides of each mount assembly (H). (See Figure 9) (J) x 2 (Z) x 2 teardrop holes...
- Page 9 Installation Instructions OXCM1U Use four 5/16-18 hex nuts (BB) and four 5/16" washers (CC) to secure four wind shield connectors (HH) to side wind shields (J). (See Figure 13) teardrop mounting hole (Center wind shields (CC) x 4 hidden for transparency)
- Page 10 OXCM1U mounts does not exceed 250 lbs (113.4 kg). Ensure that the latch mechanisms on interface brackets (L) are already lowered. (See Figure 17)
- Page 11 Installation Instructions OXCM1U Fasten brackets against ceiling mount extrusion using two If necessary, loosen button head tilt friction bolt (located on #10-24 x 1/2" socket head cap screws (M). (See Figure 20) side of interface bracket). (See Figure 22) Repeat for other interface bracket.
- Page 12 OXCM1U Installation Instructions Level Adjustment Using Bolts/Nuts Adjust level adjustment screws to change roll position.The NOTE: This will keep latch from opening but does not provide roll may be adjusted 1° in either direction. (See Figure 23) additional security for the displays.
- Page 13 Installation Instructions OXCM1U...
- Page 14 OXCM1U Installation Instructions...
- Page 15 Installation Instructions OXCM1U...
- Page 16 Europe A Franklinstraat 14, 6003 DK Weert, Netherlands P +31 (0) 495 580 852 F +31 (0) 495 580 845 Chief, a products division of Asia Pacific A Office No. 918 on 9/F, Shatin Galleria Milestone AV Technologies 18-24 Shan Mei Street...
Need help?
Do you have a question about the OXCM1U and is the answer not in the manual?
Questions and answers