Table of Contents
Advertisement
UHF
WALL FAN HEATER
THANK YOU FOR YOUR PURCHASE!
QUESTION? PROBLEM? CONTACT STELPRO CUSTOMER SERVICE.
WWW.UNIWATT.CA
CONTACT@STELPRO.COM
450-441-6020
1-866-766-6020
UNIWATT is a line of products manufactured by STELPRO.
For more information, please contact customer service.
TM
UHF1002WCW
UHF1002TTW
OWNER'S MANUAL
THIS UNIT
COMPLIES WITH
CSA STANDARDS
Advertisement
Table of Contents
Related Manuals for uniwatt UHF1002WCW
Summary of Contents for uniwatt UHF1002WCW
- Page 1 WALL FAN HEATER UHF1002TTW THANK YOU FOR YOUR PURCHASE! QUESTION? PROBLEM? CONTACT STELPRO CUSTOMER SERVICE. WWW.UNIWATT.CA CONTACT@STELPRO.COM 450-441-6020 1-866-766-6020 THIS UNIT UNIWATT is a line of products manufactured by STELPRO. COMPLIES WITH For more information, please contact customer service. CSA STANDARDS...
-
Page 2: Important Instructions
“Ressources/ for some time after shut down. Heating Calculator” section of the UNIWATT website. Do not insert or allow foreign objects to enter any air vent as this If the unit capacity is insufficient for the size of the room, it will be may cause electric shocks, fires or damages to the unit. -
Page 3: Tools Required
(model UHF1002TTW) directly to a stud. CONTROL AND COMPATIBILITY You can control your UHF fan heater in multiple ways: UHF1002WCW UHF1002TTW With a compatible wall thermostat that: • Has a fan heater mode With its integrated mechanical thermostat and timer •... - Page 4 WHERE TO INSTALL YOUR FAN HEATER Make sure that objects or furniture near the heater can Install your fan heater in an unobstructed location at least withstand the heat it gives off. 6 in. (15 cm) off the ground. Do not install the heater on a wall behind a door. TIP: You can access the fan heater’s controls more easily If a piece of furniture is nearby, make sure the fan heater will if you install it 12 in.
- Page 5 WARNING: This product must be installed by a certified electrician according to the electrical and building codes effective in your region. CUTTING THE POWER SUPPLY To protect yourself from the risk of electric shock, turn off the power to the lead wires from the electrical panel. PREPARING THE SURFACE FOR INSTALLATION...
- Page 6 PREPARING THE FAN HEATER 1. Pivot the fan heater’s front 2. Remove the two screws. 3. Lift the top [3] of the mecha- panel toward the top of the Keep the screws with the nical housing [A] and slide it unit [1] and slide it up.
- Page 7 6. Insert the power cable 7. Attach the self-adhering 5. Place the wire clamp [E] through the wire clamp and spacer [F] to one of the four in the hole. secure it. specially identified spots on the external side of the back box that will rest against the stud.
-
Page 8: Connecting The Wiring
Warning: Use copper or aluminium wires only. Use CONNECTING THE WIRING supply wires suitable for 194 °F. 1. If needed, strip the power cable wires with a wire stripper. 2. Connect the fan heater and power supply wires with the CONNECTION DIAGRAM supplied connection caps [A] according to the connection diagram. -
Page 9: Attaching The Front Panel
ATTACHING THE FRONT PANEL 1. Press the top of the front panel against the wall, keeping it slightly tilted [A] and centered with respect to the mechanical housing. 2. Carefully slide the front panel down until the hooks behind the front panel [B] are engaged and then pivot it toward the wall. - Page 10 CONTROLING THE FAN HEATER According on your model, see the table below for how to control your fan heater. With a compatible wall thermostat to adjust the room’s temperature UHF1002WCW setpoint With its integrated mechanical thermostat and timer • The temperature setpoint is controlled with the knob with settings from...
- Page 11 TROUBLESHOOTING THE FAN HEATER The following table outlines the most common issues and alerts you could WWW.STELPRO.COM experience with your fan heater. CONTACT@STELPRO.COM If your problem is not listed in the table below or the proposed solution 450-441-6020 does not solve the problem, turn the power off and contact our customer 1-866-766-6020 service team.
-
Page 12: Claim Procedure
STELPRO LIMITED WARRANTY This limited warranty is offered by STELPRO Design inc. (“STELPRO”) and applies to the following product made by STELPRO: UFH model. Please read this limited warranty carefully. Subject to the terms of this warranty, STELPRO warrants its products and their components against defects in workmanship and/or materials for the following periods from the date of purchase: 2 years.
Need help?
Do you have a question about the UHF1002WCW and is the answer not in the manual?
Questions and answers