Download
 Share
 Print this page
  1. Manuals
  2. Brands
  3. D-Link Manuals
  4. Accessories
  5. DCH-Z122
  6. Manual

D-Link DCH-Z122 Manual

Pir motion sensor
Hide thumbs
   
1
2
3
4
5
6
7
8
9
  • Contents

Advertisement

Quick Links

x
Download this manual
Download this manual
Table of Contents
DCH-122 PIR Motion Sensor
The DCH-122 has PIR motion sensor function in one, based on Z-
Wave
TM
technology.
It is the Z-Wave
TM
plus product, it support the security, ... Those
newest features of the Z-Wave
communication protocol designed for home automation, specifically to
remotely control applications in residential and light commercial
environments. The technology uses a low-power RF radio embedded or
retrofitted into home electronics devices and systems, such as lighting,
home access control, entertainment systems and household appliances.
This product can be included and operated in any Z-Wave
with other Z-Wave
TM
certified devices from other manufacturers and/or
other applications. All non-battery operated nodes within the network
will act as repeaters regardless of vendor to increase reliability of the
network.
The device adopt the Z-Wave
network system is all made by Z-Wave
network system will have the advantages as below.
•
Concurrent multi-channel support reduces external interference.
TM
technology. Z-Wave
TM
TM
500 series chip, when your Z-Wave
TM
500 series devices. The
•
Better RF range, improve about 10 meters in indoor.
•
Support 100 Kbps transmit speed, speed up communication.
Add to/Remove from Z-Wave
There are two tamper keys in the device, one is in the back side,
another is in the front side. Both of them can add, remove, reset or
association from Z-Wave
In the first time, add the device into the Z-Wave
make sure the primary controller is in the add mode. And then power
on the device, just take out the insulation Mylar in the back side of the
device. The device will auto start the NWI (Network Wide Inclusion)
mode. And it should be included in 5 seconds. You will see the LED
light ON one second.
is a wireless
Notice: Including a node ID allocated by Z-Wave
"Add" or "Inclusion". Excluding a node ID allocated by Z-Wave
Controller means "Remove" or "Exclusion".
TM
network
Function
Add
TM
1
TM
Network
TM
network.
Description
1. Have Z-Wave
TM
Controller entered inclusion mode.
2. Pressing tamper key three times within 1.5 seconds
to enter the inclusion mode.
3. After add successful, the device will wake to
receive the setting command from Z-Wave
Controller about 20 seconds.
TM
network. First,
TM
Controller means
TM
TM

Advertisement

loading

  Related Manuals for D-Link DCH-Z122

  Summary of Contents for D-Link DCH-Z122

  • Page 1 • Better RF range, improve about 10 meters in indoor. DCH-122 PIR Motion Sensor • Support 100 Kbps transmit speed, speed up communication. Add to/Remove from Z-Wave Network There are two tamper keys in the device, one is in the back side, another is in the front side.
  • Page 2 1. Have Z-Wave Controller entered exclusion mode. Z-Wave Notification 2. Pressing tamper key three times within 1.5 seconds Remove to enter the exclusion mode. After the device adding to the network, it will wake-up once per day in Node ID has been excluded. default.

  • Page 3: Power Up Procedure

    report except the low battery detection. * Tamper Report: Both the 2 tamper keys are pressed over 5 seconds. The device will Power Up Procedure into the alarm state. In that state, if any one of the tamper keys be released, the device will unsolicited to send the report to the nodes in the group 1.

  • Page 4: Operation Mode

    CC wrapped to communicate, otherwise it will not response. configuration NO. 8. COMMAND_CLASS_BATTERY Notice: When the tamper key of the back side is released, the device COMMAND_CLASS_NOTIFICATION_V4 always in the “Test Mode”, no matter the DIP switch setting. COMMAND_CLASS_ASSOCIATION_V2 COMMAND_CLASS_CONFIGURATION Battery Installation COMMAND_CLASS_SENSOR_BINARY_V2 COMMAND_CLASS_SENSOR_MULTILEVEL_V5...

  • Page 5: Z-Wave Configuration Settings

    of the device. The device will auto start the NWI (Network Wide Inclusion) mode. And it should be included in 5 seconds. You will see the LED light ON one second. 2. Let the controller associate with the device into the first group, any light switch that intend to be turned on when the device trig please associate with the device into the second group.
  • Page 6 Vali Vali Name Description Name Description Def. A B C Def. A B C Setting the BASIC command value to turn on the light. The 0xFF(-1) means Operation mode. Using bit to control. turn on the light. For dimmer Caution: The value is unsigned byte, Basic Set equipment 1 to 100 means the light ...
  • Page 7 Vali Vali Name Description Name Description Def. A B C Def. A B C the range is from 0x00 ~ 0xFF. received the trigger signal too frequently. Also can save the battery    Bit0: Reserve. energy. Bit1: Enable sending motion OFF Notice: If this value bigger than the report.

  • Page 8: Z-Wave Supported Command Class

    Z-Wave Supported Command Class Specifications subject to change without notice due to continuing COMMAND_CLASS_ZWAVEPLUS_INFO_V2 product improvement. COMMAND_CLASS_BATTERY COMMAND_CLASS_NOTIFICATION_V4 COMMAND_CLASS_ASSOCIATION_V2 COMMAND_CLASS_CONFIGURATION COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2 COMMAND_CLASS_VERSION_V2 COMMAND_CLASS_SENSOR_BINARY_V2 FCC ID: KA2CHZ122A1 COMMAND_CLASS_SENSOR_MULTILEVEL_V5 COMMAND_CLASS_WAKE_UP_V2 COMMAND_CLASS_ASSOCIATION_GRP_INFO IC ID: 4216A-CHZ122A1 COMMAND_CLASS_POWERLEVEL COMMAND_CLASS_DEVICE_RESET_LOCALLY COMMAND_CLASS_MULTI_CMD Disposal COMMAND_CLASS_SECURITY This marking indicates that this product should not be COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2 disposed with other household wastes throughout the EU.
  • Page 9 used in accordance with the instructions, may cause harmful your health and well-being. interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If When replacing old appliances with new once, the retailer is legally this equipment does cause harmful interference to radio or television obligated to take back your old appliance for disposal at least for free reception, which can be determined by turning the equipment off and...