D-Link DCH-112 Manual

D-Link DCH-112 Manual

Door/ window sensor

Advertisement

Quick Links

DCH-112 Door/ Window Sensor
The DCH-112 has door/window sensor function in one, based on Z-
Wave
TM
technology.
It is the Z-Wave
TM
plus product, it support the security, OTA... Those
newest features of the Z-Wave
communication protocol designed for home automation, specifically to
remotely control applications in residential and light commercial
environments. The technology uses a low-power RF radio embedded or
retrofitted into home electronics devices and systems, such as lighting,
home access control, entertainment systems and household appliances.
This product can be included and operated in any Z-Wave
with other Z-Wave
TM
certified devices from other manufacturers and/or
other applications. All non-battery operated nodes within the network
will act as repeaters regardless of vendor to increase reliability of the
network.
The device adopt the Z-Wave
TM
technology. Z-Wave
TM
TM
500 series chip, when your Z-Wave
network system is all made by Z-Wave
network system will have the advantages as below.
Concurrent multi-channel support reduces external interference.
Better RF range, improve about 10 meters in indoor.
Support 100 Kbps transmit speed, speed up communication.
Add to/Remove from Z-Wave
There are two tamper keys in the device, one is in the back side,
another is in the front side. Both of them can add, remove, reset or
association from Z-Wave
In the first time, add the device into the Z-Wave
make sure the primary controller is in the add mode. And then power
on the device, just take out the insulation Mylar in the back side of the
device. The device will auto start the NWI (Network Wide Inclusion)
mode. And it should be included in 5 seconds. You will see the LED
light ON one second.
Notice: Including a node ID allocated by Z-Wave
is a wireless
"Add" or "Inclusion". Excluding a node ID allocated by Z-Wave
Controller means "Remove" or "Exclusion".
TM
network
Function
Add
TM
1
TM
Network
TM
network.
Description
1. Have Z-Wave
TM
Controller entered inclusion mode.
2. Pressing tamper key three times within 1.5 seconds
to enter the inclusion mode.
3. After add successful, the device will wake to
receive the setting command from Z-Wave
TM
500 series devices. The
TM
network. First,
TM
Controller means
TM
TM

Advertisement

Table of Contents
loading

Summary of Contents for D-Link DCH-112

  • Page 1 The device will auto start the NWI (Network Wide Inclusion) mode. And it should be included in 5 seconds. You will see the LED The DCH-112 has door/window sensor function in one, based on Z- light ON one second.
  • Page 2 Notice 2: When the device into NWI mode, the sensor functionality Controller about 20 seconds. will useless. The NWI mode will timeout after 30 seconds. You can press the tamper key 3 times to abort the NWI mode. 1. Have Z-Wave Controller entered exclusion mode.
  • Page 3: Power Up Procedure

    * Door/Window Report: * Timing Report: When the door/window state changed, the device will unsolicited to Beside the event triggered could report message, the device also send the report to the nodes in the group 1. support the timing unsolicited report of the status. •...
  • Page 4: Security Network

    temperature and the illumination level. The user can switch the report * Wake by setting the configuration NO. 5 bit4 (illumination) and bit5 When the device power on, the device will wake about 20 seconds. In (temperature), and the configuration NO. 7 bit6 (battery). this duration, the controller can communicate with the device.
  • Page 5: Choosing A Suitable Location

    1. Put the front cover bottom to 1-1, and press down. mounting the sensor by using tape B. The tamper key will pressed and 2. Push the front cover top to 2-1. let the sensor enter normal mode. Choosing a Suitable Location Z-Wave Configuration Settings 1.
  • Page 6 Vali Vali Name Description Name Description Def. A B C Def. A B C    Setting the BASIC command value to Bit6: Reserve. turn on the light. The 0xFF(-1) means Disable the back key release Bit7: turn on the light. For dimmer ...
  • Page 7: Z-Wave Supported Command Class

    Temperatur temperature. Signal (Frequency): e Time The default value is 12. The tick time DCH-112: 868.40 MHz, 869.85 MHz(EU), can setting by the configuration No.20. DCH-112: 908.40 MHz, 916.00 MHz(US),(Canada) The interval time for auto report each DCH-112: 922~927 MHz(JP/TW), tick.
  • Page 8: Fcc Interference Statement

    interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of...
  • Page 9 appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being. When replacing old appliances with new once, the retailer is legally obligated to take back your old appliance for disposal at least for free of charge.

Table of Contents