Download Table of Contents Print this page
D-Link DCH-Z120 Manual

D-Link DCH-Z120 Manual


Quick Links

The sensor DCH-Z110/Z120 have PIR or door/window integrated with,
temperature and illumination, which are 3 sensors function in one,
based on Z-Wave
It is the Z-Wave
plus product, it supports the security, OTA... Those
newest features of the Z-Wave
communication protocol designed for home automation, specifically to
remotely control applications in residential and light commercial
environments. The technology uses a low-power RF radio embedded or
retrofitted into home electronics devices and systems, such as lighting,
home access control, entertainment systems and household appliances.
This product can be included and operated in any Z-Wave
with other Z-Wave
certified devices from other manufacturers and/or
other applications. All non-battery operated nodes within the network
will act as repeaters regardless of vendor to increase reliability of the
technology. Z-Wave
is a wireless
The device adopt the Z-Wave
network system is all made by Z-Wave
network system will have the advantages as below.
•Concurrent multi-channel support reduces external interference.
•Better RF range, improve about 10 meters in indoor.
•Support 100 Kbps transmit speed, speed up communication.
Function Compare DCH-Z110/DCH-Z120
Add to/Remove from Z-Wave
There are two tamper keys in the device, one is in the back side,
another is in the front side. Both of them can add, remove, reset or
association from Z-Wave
In the first time, add the device into the Z-Wave
make sure the primary controller is in the add mode. And then power
on the device, just take out the insulation Mylar in the back side of the
device. The device will auto start the NWI (Network Wide Inclusion)
mode. And it should be included in 5 seconds. You will see the LED
light ON one second.
500 series chip, when your Z-Wave
500 series devices. The
Temperature Illumination
network. First,


Table of Contents

Summary of Contents for D-Link DCH-Z120

  • Page 1 500 series devices. The network system will have the advantages as below. •Concurrent multi-channel support reduces external interference. •Better RF range, improve about 10 meters in indoor. •Support 100 Kbps transmit speed, speed up communication. Function Compare DCH-Z110/DCH-Z120 Temperature Illumination Door/Window DCH-Z110 DCH-Z120...
  • Page 2: Function Description

    receiving the report message, like triggered event, temperature, illumination etc. The group 2 is for light control, the device will send the “Basic Set” command to this group. And each group support 8 nodes Notice: Including a node ID allocated by Z-Wave Controller means maximum.
  • Page 3 Event: Tampering. Product covering removed (0x03) * Motion Report: Sensor Binary Report (V2) When the PIR motion detected, the device will unsolicited to send the report to the nodes in the group 1. Sensor Type: Tamper (0x08) Sensor Value: 0xFF Notification Report (V4) * Temperature Report: When the PIR motion detected or the door/window state changed, the...
  • Page 4: Power Up Procedure

    This function default is disabled, to enable this function by setting the configuration NO.22 not to zero. Power Up Procedure Enable this functionality, the device will measure the illumination in every one minute. And if the illumination is changed to plus or minus the value (setting by the configuration NO.22), the device will report * Battery Power Check illumination information to the nodes in the group 1.
  • Page 5: Security Network

    After finish the firmware download, the LED will start flash in every 0.5 temperature and the illumination level. The user can switch the report second. At that time, please don't remove the battery , otherwise it by setting the configuration NO. 5 bit4 (illumination) and bit5 will cause the firmware broken, and the device will no function.
  • Page 7: Battery Installation

    3.Hold the front cover and pull up Choosing a Suitable Location 1.The recommended mounting height is 160cm for DCH-Z120. 2.Don't let the device facing the window or the sunlight. 3.Don't let the device facing the source of heat. For instance the heater Replace the new battery and install the cover back.
  • Page 8: Installation

    After finish the test and decide to fix, then you can remove tape A, and Installation mounting the sensor by using tape B. The tamper key will pressed and let the sensor enter normal mode. 1. In the first time, add the device into the Z-Wave network.
  • Page 9 Name Description Name Description Def. Def. Valid Valid Setting the BASIC command value to Operation mode. Using bit to control. turn on the light. The 0xFF(-1) means   Bit0: Reserve. Basic Set turn on the light. For dimmer   0xFF Bit1: 1 means test mode, Level...
  • Page 10 Name Description Def. useless. Valid Notice: If the configuration No.9 is Mult- Multisensor function switch. Using bit zero, this setting is useless. Sensor to control.   Function Bit6: Reserve. Bit0: Disable magnetic integrate Switch   illumination to turn ON the lighting Bit7: Reserve.
  • Page 11 0:Enable) can setting by the configuration No.20.   Name Description Def. Bit7: Reserve. Valid Name Description Name Description Def. Def. Valid Valid In the normal mode, after the PIR The interval time for auto report the motion detected, setting the re-detect illumination.
  • Page 12: Specifications

    “Illumination Report” section. 869.00 MHz(RU), 865.20 MHz(IN), 916.00 MHz(IL), Name Description Def. Valid Note: Refer A as DCH-Z110, B as DCH-Z120 Z-Wave Supported Command Class Range: Minimum 30 meters indoor, COMMAND_CLASS_ZWAVEPLUS_INFO_V2 70 meters outdoor line of sight. COMMAND_CLASS_BATTERY Operating Temperature: -10...
  • Page 13: Fcc Interference Statement

    FCC Interference Statement Warning This equipment has been tested and found to comply with the limits for Do not dispose of electrical appliances as unsorted municipal waste, a Class B digital device, pursuant to Part 15 of the FCC Rules. These use separate collection facilities.

This manual is also suitable for:


Table of Contents