Page 1
User Manual Installation Dragon PTN Interface Module PTN-4-2/4WEM Installation PTN-4-2/4WEM Technical support Release 01 02/2018 https://hirschmann-support.belden.com...
Page 2
In addition, we refer to the conditions of use specified in the license contract. You can get the latest version of this manual on the Internet at the Hirschmann product site (www.hirschmann.com). Hirschmann Automation and Control GmbH Stuttgarter Str.
A general 4Wire Voice example can be found in the figure below: MPLS-TP Dragon PTN Network Dragon PTN Node WAN (via SFP on fiber) 4-2/4WEM Module PABX Packetized Voice via Voice Voice CESoPSN Links Links Leased Line LAN2 LAN1 Modem Figure 1 General 4Wire Voice Example Installation PTN-4-2/4WEM Release 01 02/2018...
Service programmed but no data received on backplane (=network) side S<n> (=future) Not lit, dark E wire (from E&M) on the front side (LAN) is not active (=E&M Signaling) Lit, Green E wire (from E&M) on the front side (LAN) is active Installation PTN-4-2/4WEM Release 01 02/2018...
A) converts this Ethernet traffic into packetized Voice MPLS-TP and transmits it via an Ethernet IFM (e.g. 4-GC-LW) onto the Dragon PTN MPLS-TP network. The packetizing of the voice input occurs via CES: CESoPSN (see §2.2.3) technique. Installation PTN-4-2/4WEM Release 01 02/2018...
The destination module will receive the transported timeslots from the Dragon PTN network and regenerate the voice data and the E&M signaling (=future) from it to finally output it on its voice port. Each end-point or port must be located in a different node. Installation PTN-4-2/4WEM Release 01 02/2018...
Hitless Switching = disabled Hitless Switching = enabled at switch-over possible data loss no data or synchronization loss total delay less than hitless switching more than protection switching Installation PTN-4-2/4WEM Release 01 02/2018...
Single Path ENABLED: no CES ONE link required MPLS-TP Dragon PTN already with one link up CES starts Voice data Voice data data MPLS-TP Dragon PTN data Figure 6 Single Path Enabled Installation PTN-4-2/4WEM Release 01 02/2018...
/ network timing per CES. The CSM synchronizes all the included IFMs in the node. The application endpoints in a 'Circuit Emulation: 2W4W Voice' service can communicate in a synchronized way. Which method can be used depends on: Installation PTN-4-2/4WEM Release 01 02/2018...
Selftests can be performed via test tone generation/level metering in CESes, e.g. when configuring or troubleshooting a CES. CAUTION: enabling selftests disables or disturbs normal service traffic on a port! For more information and configuration settings, see 'Test and Loopback' in Ref.[1] in Table 1. Installation PTN-4-2/4WEM Release 01 02/2018...
S2 to S3 (=most significant). It can be read out as well via HiProvision. This edition has been factory set and MUST NOT BE CHANGED! Example: Setting S3=’0’ and S2=’5’ indicates Hardware Edition ‘5’ (dec). Figure 10 Hardware Edition Installation PTN-4-2/4WEM Release 01 02/2018...
DP (=Depacketization Delay): Delay to decode MPLS-TP packets into Serial output; DPh: Extra Depacketizing Delay due to hitless switching; Total Delay = Total Network delay between two Serial applications; Total Delay = (Packetization + Path + Depacketization + Hitless Switching) Delay; Installation PTN-4-2/4WEM Release 01 02/2018...
MaxNetwPathDelayDiff = 9*10 + 250 = 340 µs; 3.3.3 Estimated Delay Calculation and Formulas Table 8 shows formulas to calculate an estimated delay. Once you have the desired estimated delay, fill out the parameter values in HiProvision, which shows the calculated ‘P+DP+DPh’. Installation PTN-4-2/4WEM Release 01 02/2018...
→ 1-6 TDM frames/packet; if less bandwidth is required and delay is not important → at least 8 TDM frames/packet; if less bandwidth and a small delay are wanted → 8 .. 10 TDM frames/packet. Installation PTN-4-2/4WEM Release 01 02/2018...
Need help?
Do you have a question about the PTN-4-2/4WEM and is the answer not in the manual?
Questions and answers