Advertisement
INSTALLATION, OPERATION & MAINTENANCE
AVANTCO SERIES 177AG OWNER'S MANUAL
Manual Griddles:
Radiant Charbroilers:
Hot Plates:
All equipment manufactured by Avantco is for use with the type of gas specified on the rating plate
and for installation that will be in accordance with National Fuel Gas Code ANSI Z223.1 (latest edition).
FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors
or liquids in the vicinity of this or any other appliance.
WARNING: Improper installation, adjustment, alteration, service or
maintenance can cause property damage, injury or death. Read the installation,
operating and maintenance instructions thoroughly before installing or
servicing this equipment.
Instructions to be followed in the event the user smells gas must be posted in a prominent
location in the kitchen area. This information shall be obtained from the local gas supplier.
PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE
This equipment is design engineered for commercial use only.
177AG24MG • 177AG36MG • 177AG48MG
177AG24RC • 177AG36RC • 177AG48RC
177AGR212 • 177AGR424 • 177AGR636
02/2019
Page |
1
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Avantco 177AG series
Summary of Contents for Avantco 177AG series
- Page 1 177AGR212 • 177AGR424 • 177AGR636 All equipment manufactured by Avantco is for use with the type of gas specified on the rating plate and for installation that will be in accordance with National Fuel Gas Code ANSI Z223.1 (latest edition).
-
Page 2: Table Of Contents
TABLE OF CONTENTS Installation Instructions............... 2 Operating Instructions . -
Page 3: Operating Instructions
GAS CONNECTION The gas supply (service) line must be the same size or greater than the inlet line of the appliance. Avantco appliances use a ¾” NPT inlet. Sealant on all pipe joints must be resistive to LP gas. MANUAL SHUT OFF VALVE This installer-supplied valve must be in the gas service line ahead of the appliance regulator in the gas stream and in position accessible in the event of an emergency. - Page 4 Avantco appliance. FAILURE TO INSTALL THE PRESSURE REGULATOR WILL VOID THE APPLIANCE WARRANTY The regulators supplied along with Avantco appliances will have ¾” inlet/outlet openings. Prior to connecting the regulator, check the incoming line pressure as these regulators can only withstand a maximum pressure of ½...
-
Page 5: Cleaning & Maintenance Instructions
Check the ventilation system periodically to see that nothing has fallen down into the stub back, high riser, or high shelf exhaust vents. Ensure your Avantco cooking equipment is checked by a qualified technician once a year for efficient and long-lasting operation of the appliance. -
Page 6: Conversion
CONVERSION Instructions are for conversion from Natural Gas to Propane (L.P.) on all models. The conversion should be done before connecting the unit to the gas supply. Units are shipped from the factory equipped for use on natural gas. Orifices necessary for LP (propane) are provided in a bag tied to the valve on the front panel. -
Page 7: Specifications
COUNTERTOP EQUIPMENT SPECIFICATIONS Intake-Tube # of Burners Per BTU Total BTU Model Gas Type Pressure Nozzle & Controls B.T.U./h B.T.U./h (in.W.C.) Natural Gas 35,000 70,000 177AG24RC 2 Independent L.P. Gas 35,000 70,000 Natural Gas 35,000 105,000 177AG36RC 3 Independent L.P. Gas 35,000 105,000 Natural Gas... -
Page 8: Equipment Diagrams
177AGR212 DIAGRAM Page |... - Page 9 177AGR424 DIAGRAM Page |...
- Page 10 177AGR636 DIAGRAM Page |...
- Page 11 177AG24MG DIAGRAM Page |...
- Page 12 177AG36MG DIAGRAM Page |...
- Page 13 177AG48MG DIAGRAM Page |...
- Page 14 177AG24RC DIAGRAM Page |...
- Page 15 177AG36RC DIAGRAM Page |...
- Page 16 177AG48RC DIAGRAM Page |...
-
Page 17: Warranty
Equipment that has been changed, altered, or modified or repaired by other than an Authorized Service Agency. Avantco shall not be held liable for any damages to any person or property which may result from the use of the equipment thereafter.
Need help?
Do you have a question about the 177AG series and is the answer not in the manual?
Questions and answers