Patton electronics 2701B User Manual
G.703/g.704 ntu with eia-530, v.35, x.21 interfaces
Hide thumbs
Also See for 2701B:
- Specification sheet (2 pages) ,
- User manual (28 pages) ,
- User manual (32 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for Patton electronics 2701B
Summary of Contents for Patton electronics 2701B
- Page 1 USER MANUAL MODEL 2701/B, C, D G.703/G.704 NTU with EIA-530, V.35, X.21 Interfaces SALES OFFICE Part# 07M2701/x-A Doc# 086101UA (301) 975-1000 Revised 02/08/00 TECHNICAL SUPPORT (301) 975-1007 http://www.patton.com...
-
Page 2: Warranty Information
Patton Electronics warrants all Model 2701/I components to be free from defects, and will—at our option—repair or replace the prod- paid and insured to Patton Electronics. All returns must have a Return uct should it fail within one year from the first date of shipment. -
Page 3: General Information
2.0 GENERAL INFORMATION 3.0 CONFIGURATION Thank you for your purchase of this Patton Electronics product. The Model 2701 features configuration capability via hardware DIP This product has been thoroughly inspected and tested and is warrant- switches. This section describes all possible DIP switch configurations ed for One Year parts and labor. -
Page 4: Sw1-6 And Sw1-7 Clock Modes
Switch SW1-1 through SW1-5 OFF ON 1728kbps OFF ON 1792kbps A detailed description of each switch (SW1-1 through SW1-5) setting 1856kbps follows the summary table below. 1920kbps OFF OFF 1984kbps SWITCH SET 1 SUMMARY TABLE OFF OFF Clear Channel 2048kbps Position Function Factory Default... - Page 5 equipment connected to the unit provides a minimally accept- able pulse density. For this reason, there are advantages to SWITCH SET 2 SUMMARY TABLE using HDB3 instead. AMI coding does not inherently account Position Function Factory Default Selected Option for ones density. To meet this requirement, the user should ensure that the data inherently meets pulse density require- SW2-1 Line Coding...
-
Page 6: Switch Sw2-5 Front Panel Switches
4 4 . . 0 0 I I N N S S T T A A L L L L A A T T I I O O N N S2-4 RDL Type Initiate a V.54 RDL loop when selected Once the Model 2701 is properly configured, it is ready to connect Initiate a CSU loopback when selected to the G.703/G.704 interface, to the serial port, and to the power... - Page 7 4.1.3 Connecting the Twisted Pair (120 ohm) to the G.703 4.2 Connecting the Serial Port Network The Model 2701/B, C, D supports RS-530, V.35, X.21 serial port connections. This section describes how to connect the serial ports to The Model 2701 is equipped with a single RJ-48C jack for connec- your terminal equipment.
-
Page 8: Power Connection
TD & RD Glows yellow to indicate an idle condition of Binary “1” data on the respective terminal interface sig- tion, please contact Patton Electronics Technical support at nals. Green indicates Binary “0” data. (301)975-1007, via our web site at http://www.patton.com, or by e-mail at support@patton.com. - Page 9 pattern, the LED will remain lit if the unit does not Activate the “LL” signal on the DTE (2701/B and 2701/C receive the identical pattern. When it receives the only). If you are not sure which lead is the “LL” signal, correct pattern, the LED will turn off.
- Page 10 NOTE: The above V.52 BER tests can be used independent- ly of the Remote Digital Loopback tests. This requires two a. Activate the “RL” signal on the DTE (2701/B and 2701/C operators: one to initiate and monitor the tests at the local only).
- Page 11 A A P P P P E E N N D D I I X X A A A A P P P P E E N N D D I I X X B B PATTON MODEL 2701 PATTON ELECTRONICS MODEL 2701 INTERFACE PIN ASSIGNMENT G.703/G.704 SPECIFICATIONS...
- Page 12 A A P P P P E E N N D D I I X X C C RS-530 TO RS-530 (STRAIGHT- RS-530 TO RS-530 (CROSS OVER THROUGH CABLE) PIN OUT CABLE) PIN OUT PATTON ELECTRONICS MODEL 2701 INTERFACE PIN ASSIGNMENT Pin # Function Pin #...
- Page 13 A A P P P P E E N N D D I I X X D D V.35 TO V.35 (STRAIGHT- V.35 TO V.35 (CROSS OVER THROUGH CABLE) PIN OUT CABLE) PIN OUT PATTON ELECTRONICS MODEL 2701 Function Function INTERFACE PIN ASSIGNMENT Frame Ground Frame Ground A X.21 Interface...
-
Page 14: Factory Replacement Parts And Accessories
A A P P P P E E N N D D I I X X E E PATTON MODEL 2701 FACTORY REPLACEMENT PARTS AND ACCESSORIES Patton Model # Description 2701/B.....G.703/G.704 NTU with RS-530 interface 2701/C.....G.703/G.704 NTU with a V.35 interface 2701/D.....G.703/G.704 NTU with an X.21 interface 2701/I.......G.703/G.704 NTU w/ 10Base-T EN interface 0805US ......American Power Cord...
Need help?
Do you have a question about the 2701B and is the answer not in the manual?
Questions and answers