Advertisement
Automatic SIM card credit
interrogation
Programming by SMS
Triggering re-registration to the
GSM network
Communicator reset
Memorizing the SIM card's PIN
code in the communicator
Configuring the GPRS log-in
parameters*
ARC main tel. number/IP address
ARC backup tel. number/IP
address
Installation (alarm system) ID for
ARC use
Selecting the ARC protocol
Selection of events to report to
ARCs
Defining the delay before data is
resent to an ARC
ARC communication checking
period
(The time to wait after the last report
before performing an ARC
communication check)
Enable ARC reporting (ARC2
backs up ARC1)
Recording reports sent to ARCs in
the control panel memory
Indicate an ARC communication
fault if a report is not successfully
received by an ARC within 110
sec of transmission.
IP address for data transmission
Locking the ARC settings
Unlocking the ARC settings
These parameters effect reporting to the ARC and it is impossible to change them if the ARC settings are locked.
* These parameters cannot be programmed from the system keypad, but they can be programmed by sending SMS instructions or by Comlink software.
The JA-80Y GSM communicator
Credit balance checking is set by SMS instruction code_CREDIT_uu..u_xx_yyy_zz where uu..u =
instruction for the GSM network (e.g. ∗101# etc.), xx= period in days, yyy=minimum balance, zz=
the position in which the number showing the balance starts, If the reported credit balance is lower
than the set limit (yyy), the credit balance message from the provider will be forwarded to phone
System can be programmed remotely via SMS instruction code PRG seq, seq,... where seq is
programming sequence set also from the keypad (e.g. 8080 PRG ∗08080,201,# set the 10s exit
The communicator will unregister from the GSM network and then re-register. Also possible via
923
the SMS instruction: code GSM. Code = master, user or service code
98080
Resets to the factory default settings and erases all phone numbers, text will not be changed
xx..x = new PIN, sequence 920∗0 erases the
920 xx..x ∗0
PIN (to use a SIM card with a disabled PIN)
by SMS instruction to the alarm system: code GPRS x..x,y..y,z..z where code = master or service code, x..x =
the APN, y..y = name, z..z = password (only enter the APN if the name and password are not required by the
GSM provider)
01 a xx..x ∗0
a=1=ARC1, a=2=ARC2, xx..x = tel. number
(max.20 digits) or IP address & port – for
example: 01 2 ∗8 192 168 001 123 08080 ∗0
(∗8= signifies an IP address, it must have 12
02 a xx..x ∗0
digits followed by a 5 digit port number).
Entering 01p∗0 or 02p∗0 will erase the
number/address
a=1=ARC1, a=2=ARC2, zz..z = ID number
03 a zz..z ∗0
max. 8 digits 0 to 9 and ∗1=A to ∗6=F
(hexadecimal number)
a=1 ARC1, a=2 ARC2
04 a x
x=0 CID, x=1 SMS CID, x=2 IP CID
a=1 ARC1, a=2 ARC2
05 a ec x
ec event code (see 5.27)
x=1 report, x=0 no report
a=1 ARC1, a=2 ARC2
06 a x
x=0 to 9 min. (0=immediately, without delay)
a=1 ARC1, a=2 ARC2
07 a hhmm
hhmm = hours and minutes after last report
a=1 ARC1, a=2 ARC2
00 a x
x=0 reports disabled, x=1 reports enabled, x=2
(only for ARC2) = ARC2 backs up ARC1
x=0 no (only records ARC communication
faults, if communication checks are enabled)
08 x
x=1 yes (all reports except communication
checks)
x=0 no
09 x
x=1 yes
IP address and port in format – e.g..: 013
∗8 192 168 021 123 08080 ∗0 (∗8 mark IP
013 xx..x ∗0
address which must contain 12 digits, followed by
5 digits for the port.. Entering 013∗0 IP erase the
setting
xx..x = an installer-defined locking code (4 to 8
digits). Entering this code and then exiting
901 xx..x ∗0
service mode will lock the ARC settings
901∗0 will erase the code (= permanently
unlocked)
xx..x = the locking code used by sequence
900 xx..x ∗0
901
numbers M1 and M8
delay)
ARC programming can be temporarily
enabled in service mode by entering this
sequence. It will then relock on exiting service
mode.
- 4 -
erased
erased
0000
CID
all events are reported
1 minute
2400 (24 hours after last report)
ARC reporting disabled
yes
no
77.104.220.129 7070
(img.jablotron.com)
Unlocked
MFJ55304
Advertisement
