Advertisement
Factory-default SMS report and instruction texts
n
Factory text
0
Report from your
44
alarm:
45
1
Device
46
2
Device
47
3
Device
48
4
Device
49
5
Device
50
6
Device
201
7
Device
202
8
Device
203
9
Device
204
10
Device
205
11
Device
206
12
Device
300
13
Device
301
14
Device
302
15
Device
303
16
Device
304
17
Device
305
18
Device
306
19
Device
307
20
Device
308
21
Device
309
22
Device
310
23
Device
311
24
Device
312
25
Device
313
26
Device
314
27
Device
315
28
Device
316
29
Device
317
30
Device
318
31
Device
319
32
Device
320
33
Device
321
34
Device
322
35
Device
323
36
Device
324
37
Device
325
38
Device
326
39
Device
327
40
Device
328
41
Device
329
42
Device
330
43
Device
331
• The communicator always automatically puts numbers from 01: to 50: in front of Device or Code names.
• Texts 0 to 532 are used to create SMS event reports
• Texts 601 and 611 are SMS instructions (to control the system remotely by SMS)
• Text 419 is for the internal use of the communicator, never edit it !
5.6.
Enabling reporting to phones
Event reports can be enabled as follows:
800
all SMS and call reports disabled
801
all SMS and call reports enabled
802
all reports enabled except reports of setting and
unsetting by users 41 to 50 (i.e. their codes, cards and
key fobs). This allows setting and unsetting done by report
recipients (owners, bosses, etc.) not to be reported.
Factory default setting: 801 all reports enabled
5.7.
Remote access
Remote access (by phone or Internet) can be enabled or disabled:
9030
disabled
9031
enabled
Factory default setting: enabled
5.8.
Forwarding of incoming SMS messages
This feature enables the automatic forwarding of incoming SMS
messages which contain no valid instructions to the system:
The JA-80Y GSM communicator
n
Factory text
Device
Device
Device
Device
Device
Device
Device
Control panel
Service code
Annual inspection request
Communicator
Keypad
ARC code
Master code
Code
Code
Code
Code
Code
Code
Code
Code
Code
Code
Code
Code
Code
Code
Code
Code
Code
Code
Code
Code
Code
Code
Code
Code
Code
Code
Code
Code
Code
Code
Code
n
Factory text
332
Code
333
Code
334
Code
335
Code
336
Code
337
Code
338
Code
339
Code
340
Code
341
Code
342
Code
343
Code
344
Code
345
Code
346
Code
347
Code
348
Code
349
Code
350
Code
400
System status
401
Set
402
Unset
403
Exit delay
404
Entrance delay
405
Alarm
406
Service mode
407
Maintenance mode
408
Partial setting
409
Discharged battery
410
Tamper alarm
411
Alarm memory
412
Fault
413
Power fault
414
Unknown status
415
Time:
416
Last event:
417
Credit unknown
418
Credit:
419
(internal use only)
420
Error while processing command
421
Output turned on
422
Output turned off
501
Instant alarm
502
Delayed alarm
503
Fire
9260
messages are not forwarded, but the communicator sends
them by CLIP protocol to the simulated phone line
9261
messages are forwarded to the first programmed tel.
number in memories M1 to M8 (e.g. if numbers are only
programmed in M5 and M6, then messages will be
forwarded to M5). The tel. number from which the SMS
was received will be shown at the beginning of the
forwarded text.
Factory default setting: messages are forwarded
5.9.
SMS instruction confirmation
If the communicator receives a valid SMS instruction, the instruction
sender will be made aware of its successful execution by the reception
of a conformation SMS sent by the communicator. This confirmation
can be disabled as follows:
9270
9271
Factory default setting: enabled
5.10. Reaction to incoming calls
The communicator's reaction to incoming phone calls can be set by:
904 x
- 7 -
n
504
Panic alarm
505
Invalid code-entries exceeded
506
Alarm when power turned on
507
Tamper alarm
508
End of tamper alarm
509
End of alarm indication
510
Alarm cancelled by user
511
Setting
512
Unsetting
513
Partial setting
514
Codeless setting
515
External communication fault
516
External comm. restored
517
Fault
518
Fault no longer present
519
Mains dropout over 30 minutes
520
Mains dropout
521
Mains recovery
522
Discharged battery
523
Battery OK
524
Switching to Service Mode
525
Leaving Service Mode
526
PGX
527
PGY
528
Radio jamming present
529
Internal communication fault
530
Internal comm. restored
531
Communication test
532
Unconfirmed alarm
601
SET
602
UNSET
603
STATUS
604
MEMORY
605
PGX ON
606
PGX OFF
607
PGY ON
608
PGY OFF
609
AUX ON
610
AUX OFF
611
CREDIT
Numbers 01 to 50 for devices and
codes are automatically generated by the
communicator so it is unnecessary to
enter them in the text
disabled
enabled
Factory text
MFJ55304
Advertisement
