Advertisement
The telephone numbers M1 and M8 will also receive the GSM
provider's replay.
• If only uu..u follows the CREDIT instruction (no xx yyy zz) then
periodic balance checking will not be performed, but the balance will
be checked immediately and the uu..u checking instruction will be
memorized, so that in future it will be possible to check the balance
just by sending the instruction code CREDIT.
Example: sending the SMS instruction "code credit
causes the credit balance to be checked every 7
has been sent) and if the balance (starting with the first character in
the message from the GSM provider) is lower than 50 currency units it
will be reported.
Warning: the use of prepaid cards in the communicator is risky.
Some GSM providers block cards with enough credit but which are not
topped up frequently enough. We strongly advise the use of tariffed
SIM cards !!!
5.18. Remote programming by the SMS instruction
Instruction PRG can be used to send programming and operating
sequences to the alarm system:
code_PRG_seq,seq,seq...
where:
code
is valid access or service code (e.g. 8080 or 1234)
_
space
seq
programming sequence usually set via the keypad
Note:
• In the sequence can be used characters 0 to 9, ∗ and #)
• When the valid instruction is received, communicator simulates
entering the keys on the keypad, comma in the SMS is taken as a
pause in the sequence entering
• System must be unset and switched to the service mode
• The number of sequences in one SMS is limited by the maximum size of
the SMS in the GSM network.
Example: by sending SMS 8080 PRG
be set to 10s
5.19. Registration code for
If remote access via the Internet is desired, then the system has to be
registered on the web page:
www.GSMLink.cz
Each communicator has its own unique registration code, which is
printed on the label attached to the communicator module. This code
can also be sent by SMS to your mobile phone by the keypad entry:
910 xx...x ∗0 where
xx...x is the tel. number to send the code to
Notes:
• It takes a certain time to receive the registration code (depends on
the current traffic in the network)
• The registration code has the format: xxxxx-xxxxx-xxxx
5.20. Triggering re-registration to the GSM network
After 923 has been entered, the communicator quits the GSM network and
then re-registers itself. This re-registration does not change any settings in
the communicator. It should be used after GSM network faults or data
collisions and in some networks it also has to be used after a blocked SIM
card has been unblocked by the GSM provider.
It is also possible (if the SIM card can still receive) to trigger GSM network
re-registration by sending the SMS instruction: code GSM (code =
master, user or service code).
5.21. Communicator reset
Entering 98080 returns the communicator to its factory default settings and
texts, erases all telephone numbers and disables reporting. The text will
not be changed.
5.22. Memorizing the SIM card's PIN code in the communicator
It is recommended to use a SIM card with disabled PIN protection. If it is
impossible to disable the PIN, then it can still be used by entering the
following sequence (it must be entered after the control panel has been
powered up).
∗
920 PIN
0
Example: if the SIM card PIN is 1234 enter 9201234∗0
Notes:
If the communicator does not register to the GSM network within
1 minute of the PIN being entered (this problem is shown by red
The JA-80Y GSM communicator
∗
101# 7 50 1"
th
day (after the SMS
∗
08080,201,# the exit delay will
www.GSMLink.cz
LED flashes), then you either entered a wrong PIN or the GSM
signal is too weak. In such a case:
enter 920∗0 while in service mode (erases the entered PIN)
o
disconnect the control panel power (mains and battery)
o
take out the SIM card and try it in a mobile phone (it should
o
register to a GSM network when located at the control panel)
if you know the right PIN code and there is a GSM signal
o
strong enough, put the SIM card back into the communicator,
turn on the control panel power and then enter the PIN code
(920 PIN ∗0) – the communicator should then register to the
GSM network (its red LED should turn off within a minute)
The communicator memorizes the PIN and it will use it
automatically whenever it registers to the GSM network.
If you are replacing the SIM card in the communicator with
another one and the former one used a PIN code, first switch the
control panel to service mode and enter 920∗0 to erase the
former PIN code. The SIM card can then be changed.
Note: The PIN code cannot be changed if the ARC settings are locked
Factory default setting: The PIN code is erased
5.23. GPRS log-in parameters
GPRS data communication (wireless Internet via a GSM network) is
used for remote access via the Internet and also for IP reporting to the
ARC. To use GPRS data it must first be enabled (activated) in the SIM
card (contact your GSM provider for details). Then the GSM network's
GPRS parameters must be programmed by sending the following SMS
instruction to the communicator.
code_GPRS_ x..x,y..y,z..z
where:
code
is a valid (master, user or service) access code (e.g.
8080 or 1234)
_
space
x..x
APN (Access Point Name)
,
comma
y..y
username (do not enter if not required)
z..z
password (do not enter if not required)
Notes:
Most public GSM networks only request an APN (do not enter y..y
and z..z parameters in this case)
The GPRS parameters can only be programmed if the system is in
service mode and the ARC settings are not locked
Factory default setting: APN = Internet
5.24. ARC phone numbers / IP addresses
Events can be reported to up to 2 ARCs (which can be independent or
ARC2 can work as ARC1's backup). Each ARC can have its main and
backup phone numbers (or IP addresses) programmed with:
∗
01 a xx....x
0
Main:
∗
02 a xx....x
0
Backup:
where:
a
1=ARC1, 2=ARC2
xxx...x tel. number (max. 20 digits)
or IP address and port – entry format example:
01 2 ∗8 192 168 001 123 08080 ∗0
where ∗8 (auto-converts to #) signifies an IP address
which must have 12 digits and must be followed by the 5
digits of the port number (no separators)
To erase a tel. number / IP address enter: 01p∗0 or 02p∗0
If numbers / IP addresses are erased there will be no reporting to that
particular ARC
Note: the communicator first tries to send data to the main number /
address, if it is not successful it tries the backup.
Factory default setting: all tel. numbers / IP addresses erased
5.25. Installation (alarm system) ID for ARC use
The installation's ID number which is sent to an ARC with every report
can be programmed with:
∗
03 a zz..z
0
where:
a
1=ARC1, 2=ARC2
- 9 -
MFJ55304
Advertisement
