Advertisement

EAC 10 Control unit
Instruction manual
Valid for: from serial no. 905-xxx-xxxx
0463 609 101 GB 20200110

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EAC 10 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for ESAB EAC 10

  • Page 1 EAC 10 Control unit Instruction manual Valid for: from serial no. 905-xxx-xxxx 0463 609 101 GB 20200110...
  • Page 3: Table Of Contents

    USB connection ..................5.3.1 Insert the USB memory ................ MAINTENANCE ................... Inspection and cleaning ................. ORDERING SPARE PARTS ................ DIAGRAM ......................ORDERING NUMBERS ..................20 ACCESSORIES ....................21 Rights reserved to alter specifications without notice. 0463 609 101 © ESAB AB 2020...
  • Page 4: Safety

    Safety Data Sheets (SDSs). Safety precautions Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who works on or near the equipment observes all the relevant safety precautions. Safety precautions must meet the requirements that apply to this type of equipment. The following recommendations should be observed in addition to the standard regulations that apply to the workplace.
  • Page 5 Protect your eyes and body. Use the correct welding screen and filter lens and wear protective clothing. • Protect bystanders with suitable screens or curtains. NOISE - Excessive noise can damage hearing Protect your ears. Use earmuffs or other hearing protection. 0463 609 101 - 5 - © ESAB AB 2020...
  • Page 6 For further information contact the nearest ESAB dealer. ESAB has an assortment of welding accessories and personal protection equipment for purchase. For ordering information contact your local ESAB dealer or visit us on our website. 0463 609 101 - 6 - ©...
  • Page 7: Introduction

    (GMAW). The control unit is included in Versotrac EWT 1000 and can be used to control automated welding equipment, for example welding portals, column and booms. The control unit can be used with the following ESAB CAN based power sources: LAF, TAF and Aristo® 1000.
  • Page 8: Technical Data

    3 TECHNICAL DATA TECHNICAL DATA EAC 10, from serial no. 841-xxx-xxxx and 905-xxx-xxxx Supply voltage 60 V DC or 42 V AC, 50/60 Hz Supply voltage to control 12 V DC pendant Power requirement Max 900 VA Motor connections adapted 6 A 100% for ESAB motors Speed control Feedback from pulse encoder Operating temperature -10 to +40 °C (-14 to +104 °F)
  • Page 9: Installation

    4 INSTALLATION INSTALLATION The installation must be executed by a professional. 0463 609 101 - 9 - © ESAB AB 2020...
  • Page 10: Operation

    Manual travel motion direction OK / Setting menu Memory 1, 2, 3 / Soft keys Back Travel speed / frequency* Manual wire feed upwards USB connection *Only with Aristo® 1000 in AC mode. 0463 609 101 - 10 - © ESAB AB 2020...
  • Page 11: Connections

    Connection work piece voltage reference Connection anlogue power source brush Accessory cable entries Cable to control pendant Connection welding head NOTE! Connect only digital power source or analogue power source at a time. 0463 609 101 - 11 - © ESAB AB 2020...
  • Page 12: Connecting To Digital Power Source

    Connecting to digital power source Connect the interconnection cable to connector marked with I. Interconnection cable between CAN based ESAB power source and EAC 10 are available as accessories in different lengths. ESAB CAN based power sources are LAF xxx1, TAF xxx1 and Aristo® 1000.
  • Page 13: Connecting To Compatible Dc Analogue Power Source

    Connecting to compatible DC analogue power source Connect the interconnection cable to connector marked with II. Interconnection cable between analogue based ESAB power source and EAC 10 control unit are available as accessories in different lengths. Always use the dust cover on the connections where no cable is connected.
  • Page 14: Usb Connection

    Contact closure to pin S / trigger common. For non-ESAB power sources. Reserved for future use. To connect EAC 10 with non-ESAB SAW analogue power source, an analogue power source interface box and control cables are available as accessories. See chapter "ACCESSORIES".
  • Page 15: Maintenance

    • arc time • location of the unit • surrounding environment Usually it will be sufficient to blow the unit clean once a year, using dry compressed air (reduced pressure). 0463 609 101 - 15 - © ESAB AB 2020...
  • Page 16: Ordering Spare Parts

    Spare parts and wear parts can be ordered through your nearest ESAB dealer, see esab.com. When ordering, please state product type, serial number, designation and spare part number in accordance with the spare parts list.
  • Page 17: Diagram

    Connector for work piece voltage reference CAUTION! STATIC ELECTRICITY can damage circuit boards and electronic components. • Observe precautions for handling electrostatic sensitive devices. • Use proper static-proof bags and boxes. 0463 609 101 - 17 - © ESAB AB 2020...
  • Page 18 DIAGRAM Digital power source 0463 609 101 - 18 - © ESAB AB 2020...
  • Page 19 DIAGRAM Analogue power source 0463 609 101 - 19 - © ESAB AB 2020...
  • Page 20: Ordering Numbers

    Notes 0446 225 880 Control unit EAC 10 0463 612 * Control panel, instruction manual 0463 611 001 Spare parts list Technical documentation is available on the Internet at: www.esab.com 0463 609 101 - 20 - © ESAB AB 2020...
  • Page 21: Accessories

    0460 910 884 50 m (164 ft) 0460 910 885 75 m (246 ft) 0460 910 886 100 m (328 ft) Control cable EAC 10 - digital power source and work piece voltage reference brush 0446 146 880 5 m (16 ft) 0446 146 881 15 m (49 ft) 0446 146 882 25 m (82 ft)
  • Page 22 ACCESSORIES Welding power source interface Control cable EAC 10 - Welding power source interface 0446 179 880 15 m (49 ft) 0446 179 881 25 m (82 ft) 0446 179 882 35 m (115 ft) 0446 179 883 50 m (164 ft)
  • Page 23 ACCESSORIES 0463 609 101 - 23 - © ESAB AB 2020...
  • Page 24 For contact information visit esab.com ESAB AB, Lindholmsallén 9, Box 8004, 402 77 Gothenburg, Sweden, Phone +46 (0) 31 50 90 00 http://manuals.esab.com...

This manual is also suitable for:

0446 225 880

Table of Contents