Allen-Bradley C Series Installation Instructions Manual
Hide thumbs
Also See for C Series:
- Installation instructions manual (26 pages) ,
- Nstallation instructions (20 pages) ,
- Installation instructions (4 pages)
Table of Contents
Advertisement
POINT I/O Input Module
(Cat. No. 1734-IB2, -IB4 and -IB8, Series C)
4
3
Description
1
Mounting Base
2
Mechanical Keying (orange)
3
Module Wiring Diagram
4
Module Locking Mechanism
5
Insertable I/O Module
1
Wiring Base Assembly consists of item 1) mounting base, 1734-MB and item 7) removable
terminal block, 1734-RTB or -RTBS.
POINT I/O is a trademark of Rockwell
DeviceNet is a trademark of ODVA, Inc.
9
2
8
10
1
1
Automation1
Installation Instructions
5
6
7
Description
6
RTB Removal Handle
7
Removable Terminal Block (RTB)
8
DIN Rail Locking Screw (orange)
9
Slide-in Writable Label
10
Interlocking Side Pieces
Publication 1734-IN051D-EN-P - April 2004
1
Advertisement
Table of Contents
Related Manuals for Allen-Bradley C Series
Summary of Contents for Allen-Bradley C Series
- Page 1 Installation Instructions POINT I/O Input Module (Cat. No. 1734-IB2, -IB4 and -IB8, Series C) Description Description RTB Removal Handle Mounting Base Mechanical Keying (orange) Removable Terminal Block (RTB) Module Wiring Diagram DIN Rail Locking Screw (orange) Module Locking Mechanism Slide-in Writable Label Insertable I/O Module Interlocking Side Pieces Wiring Base Assembly consists of item 1) mounting base, 1734-MB and item 7) removable...
- Page 2 POINT I/O Input Module This Series C product can be used with DeviceNet and PROFIBUS adapters. It can be used with ControlNet and Ethernet adapters using RSLogix 5000, version 11 (or higher) software. Important User Information Solid state equipment has operational characteristics differing from those of electromechanical equipment.
- Page 3 POINT I/O Input Module Important User Information Identifies information about practices or circumstances that WARNING can cause an explosion in a hazardous environment, which may lead to personal injury or death, property damage, or economic loss. Identifies information about practices or circumstances that ATTENTION can lead to personal injury or death, property damage, or economic loss.
- Page 4 60529, as applicable, for explanations of the degrees of protection provided by different types of enclosure. Also, see the appropriate sections in this publication, as well as the Allen-Bradley publication 1770-4.1 ("Industrial Automation Wiring and Grounding Guidelines"), for additional installation requirements pertaining to this equipment.
-
Page 5: Explosion Hazard
POINT I/O Input Module EXPLOSION HAZARD WARNING • Do not disconnect equipment unless power has been removed or the area is known to be nonhazardous. • Do not disconnect connections to this equipment unless power has been removed or the area is known to be nonhazardous. -
Page 6: Installing The Mounting Base
POINT I/O Input Module POINT I/O is grounded through the DIN rail to chassis ATTENTION ground. Use zinc plated, yellow chromated steel DIN rail to assure proper grounding. Using other DIN rail materials (e.g. aluminum, plastic, etc.) which can corrode, oxidize or are poor conductors can result in improper or intermittent platform grounding. -
Page 7: Installing The Removable Terminal Block (Rtb)
POINT I/O Input Module 1. Using a bladed screwdriver, rotate the keyswitch (2) on the mounting base clockwise until the number required for the type of module being installed aligns with the notch in the base. 2. Make certain the DIN rail locking screw is in the horizontal position. (You cannot insert the module if the locking mechanism is unlocked.) 3. -
Page 8: Removing A Mounting Base
POINT I/O Input Module Removing a Mounting Base To remove a mounting base, you must remove any installed module, and the module installed in the base to the right. Remove the removable terminal block (if wired). 1. Unlatch the RTB handle on the I/O module. 2. - Page 9 POINT I/O Input Module Communicating with Your Module I/O messages are sent to (consumed) and received from (produced) the POINT I/O modules. These messages are mapped into the processor’s memory. This POINT I/O input module produces 1 byte of input data (scanner Rx).
-
Page 10: Wiring The Input Modules
POINT I/O Input Module Wiring the Input Modules 1734-IB4 1734-IB8 1734-IB2 Module Status Module Module Module Status Status Status Network Status Network Network Network Status Status Status NODE: NODE: NODE: 24VDC 24VDC 24VDC Sink Sink Sink Input Input Input Status - Input 0 & 4 Status of Input 0 Status - Input 1 &... - Page 11 POINT I/O Input Module Wiring for 1734-IB2 Sink Input In 0 In 1 Prox Prox 2-wire 3-wire V = 12/24V dc 41966 C = Common Channel Input Common Voltage Connect common on 3-wire proximity switches. 12/24V dc is supplied through the internal power bus. Publication 1734-IN051D-EN-P - April 2004...
- Page 12 POINT I/O Input Module Wiring for 1734-IB4 Sink Input In 0 In 1 2-wire 3-wire In 2 In 3 Prox Prox Prox Prox 41967 V = 12/24V dc C = Common Channel Input Common Voltage Connect common on 3-wire proximity switches. 12/24V dc is supplied through the internal power bus.
-
Page 13: Wiring For 1734-Ib8
POINT I/O Input Module Wiring for 1734-IB8 Sink Input 3-wire 3-wire Prox Prox In 0 In 1 2-wire 2-wire Prox Prox In 2 In 3 3-wire 3-wire Prox Prox In 4 In 5 2-wire 2-wire Prox In 6 Prox In 7 V = 12/24V dc 41967 C = Common... -
Page 14: Troubleshooting With The Indicators
POINT I/O Input Module 4V dc 2 Input Sink Module Cat. No. 1734-IB2 Troubleshooting with the Indicators 1734-IB4 1734-IB2 1734-IB8 Module Status Module Status Module Module Module Status Status Status Network Status Network Status Network Network Network Status Status Status NODE: NODE: NODE:... - Page 15 POINT I/O Input Module Indication Probable Cause Network Status Device is not on-line - Device has not completed dup_MAC_id test. - Device not powered - check module status indicator Flashing Green Device is on-line but has no connections in the established state.
- Page 16 POINT I/O Input Module Safety Approvals North American Hazardous Location Approval The following modules are North American Hazardous Location approved: 1734-IB2, 1734-IB4 and 1734-IB8. The following information applies when Informations sur l’utilisation de cet équipement operating this equipment in hazardous en environnements dangereux: locations: Products marked “CL I, DIV 2, GP A, B, C, D”...
-
Page 17: European Hazardous Location Approval
Class I, Zone 2 environments. • This equipment shall be used within its specified ratings defined by Allen-Bradley. • Provision shall be made to prevent the rated voltage from being exceeded by transient disturbances of more than 40%... - Page 18 POINT I/O Input Module OFF-State Current 1.5mA minimum Input Impedance 4.7KΩ maximum, 3.6KΩ nominal Input Filter Time 0.5ms hardware plus 0-63ms (user selectable) OFF to ON 0.5ms hardware plus 0-63ms (user selectable) ON to OFF Indicators 1 green/red network status indicator, logic side 1 green/red module status indicator, logic side 1734-IB2 - 2 yellow input status indicators, logic side 1734-IB4 - 4 yellow input status indicators, logic side...
- Page 19 POINT I/O Input Module Shock IEC 60068-2-27 (Test Ea, Unpackaged Shock) Operating 30g peak acceleration Non-operating 50g peak acceleration Vibration IEC 60068-2-6, (Test Fc, Operating) Tested 5g @ 10-500Hz ESD Immunity IEC 61000-4-2: 6kV contact discharges 8kV air discharges Radiated RF Immunity IEC 61000-4-3: 10V/m with 200Hz 50% Pulse 100%AM at 1890Mhz 10V/m with 200Hz 50% Pulse 100%AM at 900Mhz...
- Page 20 Field Wiring Terminations 1734-IB2 0 - Input 0 1 - Input 1 2 - No Connection 3 - No Connection 4 - Common 5 - Common 6 - User Supply 7 - User Supply 1734-IB4 0 - Input 0 1 - Input 1 2 - Input 2 3 - Input 3 4 - Common...