4.12.2 Parameters Expert Level, Diagnostics & Test - Siemens RDG400 Basic Documentation

Name
Expert level
P30 P-band / Switching differential in heating mode
P31 P-band / Switching differential in cooling mode
P32 P-band / Switching differential for radiator
P33 Dead zone in Comfort mode
P34 Setpoint differential (w
P35 Integral time
P36 Heating / cooling changeover switching point
cooling (X1/X2)
P37 Heating / cooling changeover switching point
heating (X1/X2)
P38 Functionality of X1
P39 Operating action of X1 if digital input
P40 Functionality of X2
P41 Operating action of X2 if digital input
P42 Functionality of D1
P43 Operating action of D1 if digital input
P44 Running time of Y1/Y2 output
(only when modulating PI control)
P46 Output Y1/Y2 (if not parameterized as 3-pos.)
P51 Floor heating limit temperature
P63 Minimum output limitation air flow signal
P64 Maximum output limitation air flow signal
P65 Protection heating setpoint
P66 Protection cooling setpoint
P68 Prolong Comfort period
P69 Temporary setpoint Comfort
(see also Comfort setpoint P08)
P71 Reload factory settings
Note
30 / 42
Siemens
Building Technologies
4.12.2 Parameters Expert level, diagnostics & test
Factory setting
2 K
1 K
2 K
2 K
) 2 K
D
5 min
16 °C
28 °C
1: = Ext. sensor
0 (N.O.)
2 = H/C changeover 0 = --- (no function)
0 (N.O.)
3 = Op. mode
changeover
0 (N.O.)
150 s
ON/OFF (1)
OFF
0%
100%
8 °C
OFF
OFF
OFF
OFF
P46: Setting to 2-position or 3-position is done with DIP 4
RDG100.../RDG110.../RDG140.../RDG160... Basic Documentation
Functions
Range
0.5 ... 6 K
0.5 ... 6 K
0.5 ... 6 K
0.5 ... 5 K
0.5 ... 5 K
0...10 min
10...25 °C
27...40 °C
0 = --- (no function)
1 = Room temp ext / Return temp (AI)
2 = H/C changeover (AI/DI)
3 = Operating mode contact [DI)
4 = Dew point sen. (DI)
5 = Enable electric heater (DI)
6 = Fault input (DI)
0 = Normally open / Open
1 = Normally closed / Closed
1 = Room temp ext / Return temp (AI)
2 = H/C changeover (AI/DI)
3 = Operating mode contact [DI)
4 = Dew point sen. (DI)
5 = Enable electric heater (DI)
6 = Fault input (DI)
0 = Normally open / Open
1 = Normally closed / Closed
0 = --- (no function)
2 = H/C changeover (DI)
3 = Operating mode contact [DI)
4 = Dew point sen. (DI)
5 = Enable electric heater (DI)
6 = Fault input (DI)
0 = Normally open / Open
1 = Normally closed / Closed
20...300 sec
1 = 2-position
2 = PWM
OFF, 10..50 °C
0...P64 (%)
P63...100 (%)
OFF, 5 ... W Cool Prot;
(W Cool Prot = 40 °C max)
OFF, W Heat Prot ... 40;
(W Heat Prot = 5 °C min.)
OFF; 15 ... 360 min
OFF = Disabled
ON = Enable
OFF = Disabled
ON = Reload start
0..6
0..6
0..6
CE1P3182en
28 May 2009