Page 1
Ver. 4 Please refer to the MODIFICATION NOTICE. SERVICE MANUAL MODEL E2A E1C EUT AVR-4810CI AVR-4810 AV SURROUND RECEIVER ● For purposes of improvement, specifications and design are subject to change without notice. ● Please use this service manual with referring to the operating instructions without fail.
Care is also taken with the positions of the wores omsode amd clamps or other dangerous situations. are used to keep wires away from heating and high voltage parts, so be sure to set everything back as it was originally. AVR-4810CI/AVR-4810...
Page 4
If wire bundles are untied or moved to perform adjustment or parts replacement etc., be sure to rearrange them neatly as they were originally bundled or placed afterward. Otherwise, incorrect arrangement can be a cause of noise generation. Wire arrangement viewed from the top Front Panel side Back Panel side AVR-4810CI/AVR-4810...
Page 5
So make sure to memorize your setting for restoring after the initialization. JIG to use for servicing When you repair the printing board, you can use the following JIG. Please order to Denon Official Service Distributor in your region if necessary.
Page 6
(Ref. No. of EXPLODED VIEW : I-19) Z2 SP UNIT ASSIGN CONNECT-5 UNIT (Ref. No. of EXPLODED VIEW : I-20) Refer to "DISASSEMBLY 9.Z2 SP UNIT and "EXPLODED VIEW" Z2 SP UNIT (Ref. No. of EXPLODED VIEW : I-2) AVR-4810CI/AVR-4810...
Page 7
• Refer to the table below for a description of the direction in which the photos were taken. • Photographs for which no direction is indicated were taken from above the product. The photograph is AVR-4810CI. • The viewpoint of each photograph...
Page 8
(3) Remove the FFC cover and acetate tapes. Disconnect the FFC Cables. FFC Cable FFC Cable FFC Cover Direction of photograph: C Acetate tape (4) Remove the screws. Please refer to "EXPLODED VIEW" for the disassembly method of each P.W.B included in FRONT PANEL ASSY. AVR-4810CI/AVR-4810...
Page 9
BACK PANEL UNIT ASSY (1) Remove the Aluminum Tape, then remove the screws. Aluminum Tape View from bottom (2) Remove the screws. Direction of photograph: A (3) Disconnect the connector wires, then remove the screws. CX055 CX091 CX074 CY052 AVR-4810CI/AVR-4810...
Page 10
(4) Disconnect the connector wire and FFC Cable. FFC Cable FFC Cable CX068 Direction of photograph: C (5) Disconnect the connector wire. CW037 CY878 Direction of photograph: B AVR-4810CI/AVR-4810...
Page 11
(1) Remove the alminium tape. Disconnect the connector wire, FFC Cables, and board to board. MAIN CPU UNIT FFC Cable CX905 FFC Cable CX032 CY124 DIGTAL UNIT ASSY Board to board CY061 CX124 Alminium Tape FFC Cable CX058 (2) Remove the screws. Direction of photograph: A AVR-4810CI/AVR-4810...
Page 12
MAIN CPU UNIT (2) Remove the screws. A.VIDEO UNIT AUDIO UNIT Direction of photograph: A RADIATOR UNIT ASSY (3) Disconnect the connector wires. CX073 CX192 CY635 CX861 CX831 CX852 CY631 CX842 ASSIGN UNIT CX841 CX157 CX075 CY049, CX832, CX904 CY638 AVR-4810CI/AVR-4810...
Page 13
: TOP COVER → → BACK PANEL UNIT ASSY Proceeding DIGITAL UNIT ASSY → A.VIDEO UNIT, ASSIGN UNIT, AUDIO UNIT and RADIATOR UNIT ASSY → REG UNIT (1) Disconnect the board to board. Board to board Direction of photograph: A AVR-4810CI/AVR-4810...
Page 14
→ → REG UNIT AMP UNIT (1) Disconnect the connector wires. CX873 CX877 CX871 CX876 View from Top CX872 CX874 CX875 (2) Disconnect the connector wires and CORD HOLDER. CX847 CX862 CY105 CY832 View from Top CORD HOLDER CX822 AVR-4810CI/AVR-4810...
Page 15
BACK PANEL UNIT ASSY Proceeding DIGITAL UNIT ASSY → A.VIDEO UNIT, ASSIGN UNIT, AUDIO UNIT and RADIATOR UNIT ASSY → → → → REG UNIT AMP UNIT P.AMP JOINT UNIT P.AMP UNIT (1) Remove the screws. Direction of photograph: B AVR-4810CI/AVR-4810...
Page 16
DIGITAL UNIT ASSY → A.VIDEO UNIT, ASSIGN UNIT, AUDIO UNIT and RADIATOR UNIT ASSY → → → → REG UNIT AMP UNIT P.AMP JOINT UNIT P.AMP UNIT → Z2 SP UNIT (1) Remove the screws and disconnect the connector wire. CX834 AVR-4810CI/AVR-4810...
Page 17
DIRECT Access Remote Maintenance mode via the internet.Installer Setup CURSOR is displayed on GUI/Option Menu. Installer Setup mode MENU LEFT ※ Refer to AVR_RemoteMaintenance_.pdf of SDI. PURE DIRECT/ STANDARD DIRECT STEREO ENTER STATUS CURSOR RETURN SIMULATION ON/OFF ZONE2 MENU AVR-4810CI/AVR-4810...
Page 18
* H D D S P : C 0 0 0 2 . 0 0 0 * M u l t E Q P r o A P P ⑭ MultEQ Pro APP * M u l t E Q P r o I C L ⑮ MultEQ Pro ICL AVR-4810CI/AVR-4810...
Page 19
No change to DSP3 FLAG0 port "H" before DSP version read. " □ DSP3 □ ERROR □13□ □ " ⑥ Error appeared in EEPROM checksum.(*** is a block address number.) EEPROM NG "□E2PROM□ERR***□ □" (No error display, version display ⑦ Both SUB/DSP only) /EEPROM OK AVR-4810CI/AVR-4810...
Page 20
(1) ASO/DC PROTECTION : Flashes in cycles of 0.5 seconds (0.25 seconds lit, 0.25 seconds off) (2) THERMAL PROTECTION : Flashes in cycles of 2 seconds (1 second lit, 1 second off) AVR-4810CI/AVR-4810...
Page 21
> 3.Press the "ENTER" button. 4. Press the "ON/OFF" button to turn the power off. 5. Then, press the "ON/OFF" button to turn the power on. NOT : Backup data(Remove settings for Installer Setup) initialization is carried out automatically. AVR-4810CI/AVR-4810...
Page 22
Once updating starts, normal operations on the AVR-4810 cannot be performed until updating is completed. Also, setting items of the GUI menu of AVR-4810 or setting items of the image adjustment may be initialized. Make a note of the settings before updating, and set them again after updating. AVR-4810CI/AVR-4810...
Page 23
1.3. About the error code See the chart below for error codes, details of faults, and coping strategies when firmware updates are performed through DPMS (Denon Product Management Server). Error Details of Error code Display Coping strategies code Reset and update again.
Page 24
* * * m i n Carry out the update in an environment Sub CPU, DSP, FPGA, and PLD. that has little network load. C o n n e c t i o n F a i l 5 3 AVR-4810CI/AVR-4810...
Page 25
Turn the power off then back on. G U I F l a s h * * * m i n and before deleting serial flash. Updating starts automatically. U p d a t i n g f a i l AVR-4810CI/AVR-4810...
Page 26
* * * m i n Mode) IP address before rewriting Carry out the update in an environment DM870 (AutoIP). that has little network load. C o n n e c t i o n F a i l A 8 AVR-4810CI/AVR-4810...
Page 27
E t h e r I M G * * * m i n rewriting DM870 related firmware. Carry out the update in an environment U p d a t i n g f a i l that has little network load. AVR-4810CI/AVR-4810...
Page 28
B0 ∼ B2 U p d a t i n g A0 ∼ AF E t h e r I M G * * * m i n DM870 Image B0 ∼ B2 U p d a t i n g AVR-4810CI/AVR-4810...
(7) Adjust the Variable Resistors of other channels in the same way. (8) After 5 minutes from (6), turn VR101 to set the voltage to 12 mV ± 0.5 mV DC. (9) Adjust the Variable Resistors of other channels in the same way. AVR-4810CI/AVR-4810...
Page 30
VR601 VR401 VR201 VR101 VR501 VR502 CX504 Audio Section Adjustment volume is set for 8U-110049-1 ∼ 7. The test point is at 8U-110067-3, 8U-110074-2. Insert an adjustment driver / connection terminal from an adjustment aperture of 8U-110048-4(POWER SUPPLY Unit)P.W.B.. AVR-4810CI/AVR-4810...
Page 31
SURROUND MODES AND PARAMETERS AVR-4810CI/AVR-4810...
DVD for the function. (COMPONENT1 input) Checking the video convert ON/OFF settings Video convert ON Video convert OFF Input Input Input Input Input Input CVBS COMPONENT CVBS COMPONENT No output No output Interlace Progressive Interlace Progressive no output AVR-4810CI/AVR-4810...
Page 38
IC108-9pin : L(0V) Check soldering of IC108. Check input/output of AMP. Input : IC112-5pin Check soldering of IC112. Output : IC112-7pin Check cable between main unit and mon- itor or Check monitor. ※ Unless specified, 8U-210063-1 A.VIDEO UNIT part. AVR-4810CI/AVR-4810...
Page 39
IC108-9pin : L(0V) Check soldering of IC108. Check input/output of AMP. Input : IC112-5pin Check soldering of IC112. Output : IC112-7pin Check cable between main unit and mon- itor or Check monitor. ※ Unless specified, 8U-210063-1 A.VIDEO UNIT part. AVR-4810CI/AVR-4810...
Page 40
IC108-9pin : L(0V) Check soldering of IC108. Check input/output of AMP. Input : IC112-5pin Check soldering of IC112. Output : IC112-7pin Check cable between main unit and mon- itor or Check monitor. ※ Unless specified, 8U-210063-1 A.VIDEO UNIT part. AVR-4810CI/AVR-4810...
Page 41
Output : IC108-13pin Check soldering of IC108. Check input/output of AMP. Input : IC112-5pin Check soldering of IC112. Output : IC112-7pin Check cable between main unit and mon- itor or Check monitor. ※ Unless specified, 8U-210063-1 A.VIDEO UNIT part. AVR-4810CI/AVR-4810...
Page 42
2.2. ZONE2 MONITOR OUT (CVBS) Output NG ZONE2 MONITOR OUT (CVBS) Output NG. ※ When checking operation, select DVD for the function. Turn on ZONE2 and check Check ZONE2 is power on. again. Input Input Input CVBS COMPONENT No output AVR-4810CI/AVR-4810...
Page 43
IC105-10pin : H(+5V) Check soldering of IC105. Check input/output of AMP. Input : IC112-3pin Check soldering of IC112. Output : IC112-1pin Check cable between main unit and mon- itor or Check monitor. ※ Unless specified, 8U-210063-1 A.VIDEO UNIT part. AVR-4810CI/AVR-4810...
Page 44
IC105-10pin : H(+5V) Check soldering of IC105. Check input/output of AMP. Input : IC112-3pin Check soldering of IC112. Output : IC112-1pin Check cable between main unit and mon- itor or Check monitor. ※ Unless specified, 8U-210063-1 A.VIDEO UNIT part. AVR-4810CI/AVR-4810...
Page 45
2.3. VCR/DVR MONITOR OUT(CVBS) Output NG VCR/DVR MONITOR OUT(CVBS) Output NG. When checking operation, select DVD for the function. Input Input Input CVBS COMPONENT No output No output VCR : G DVR : H AVR-4810CI/AVR-4810...
Page 46
Check IC303 and CX141 solder- Input : IC101-12pin IC101-16pin : H(5V) ing, or DIGITAL UNIT flaw. Output : IC101-24pin Check soldering of IC101. Check cable between main unit and mon- itor or Check monitor. Unless specified, 8U-210063-1 A.VIDEO UNIT part. AVR-4810CI/AVR-4810...
Page 47
Check IC303 and CX141 solder- Input : IC101-3pin IC101-7pin : H(5V) ing, or DIGITAL UNIT flaw. Output :IC101-33pin Check soldering of IC101. Check cable between main unit and mon- itor or Check monitor. Unless specified, 8U-210063-1 A.VIDEO UNIT part. AVR-4810CI/AVR-4810...
Page 48
DVD for the function. (COMPONENT1 Input) Checking the video convert ON/OFF settings Video convert ON Video convert OFF Input Input Input Input Input Input CVBS COMPONENT CVBS COMPONENT No output No output Interlace Progressive Interlace Progressive No output AVR-4810CI/AVR-4810...
Page 49
Check input/output of AMP. Input Y: IC111-3pin Input C: IC111-5pin Check soldering of IC111. Output Y : IC111-1pin Output C : IC111-7pin Check cable between main unit and mon- itor or Check monitor. Unless specified, 8U-210063-1 A.VIDEO UNIT part. AVR-4810CI/AVR-4810...
Page 50
Check input/output of AMP. Input Y : IC111-3pin Input C : IC111-5pin Check soldering of IC111. Output Y : IC111-1pin Output C : IC111-7pin Check cable between main unit and mon- itor or Check monitor. ※ Unless specified, 8U-210063-1 A.VIDEO UNIT part. AVR-4810CI/AVR-4810...
Page 51
Input Y : IC111-3pin Input C : IC111-5pin Check soldering of IC111. Output Y : IC111-1pin Output C : IC111-7pin Check cable between main unit and mon- itor or Check monitor . ※ Unless specified, 8U-210063-1 A.VIDEO UNIT part. AVR-4810CI/AVR-4810...
Page 52
Input Y : IC111-3pin Input C : IC111-5pin Check soldering of IC111. Output Y : IC111-1pin Output C : IC111-7pin Check cable between main unit and mon- itor or Check monitor . ※ Unless specified, 8U-210063-1 A.VIDEO UNIT part. AVR-4810CI/AVR-4810...
Page 53
2.5. VCR/DVR MONITOR OUT(S) Output NG VCR/DVR MONITOR OUT(S) Output NG. ※ When checking operation, select DVD for the function. Input Input Input CVBS COMPONENT No output No output VCR : M DVR : N AVR-4810CI/AVR-4810...
Page 54
IC101-16pin : H(+5V) ing, or DIGITAL UNIT flaw. Output Y : IC101-20pin Output C : IC101-22pin Check soldering of IC101. Check cable between main unit and mon- itor or Check monitor . ※ Unless specified, 8U-210063-1 A.VIDEO UNIT part. AVR-4810CI/AVR-4810...
Page 55
Input C : IC101-6pin IC101-7pin : H(+5V) ing, or DIGITAL UNIT flaw. Output Y : IC101-29pin Output C : IC101-31pin Check soldering of IC101. Check cable between main unit and mon- itor or Check monitor. ※ Unless specified, 8U-210063-1 A.VIDEO UNIT part. AVR-4810CI/AVR-4810...
Page 56
COMPONENT OUT Output NG. When checking operation, select DVD for the function. (COMPONENT1 Input) Checking the video convert ON/OFF settings. Video convert ON Video convert OFF Input Input Input Input Input Input CVBS COMPONENT CVBS COMPONENT No output No output AVR-4810CI/AVR-4810...
Page 57
IC504-7pin : H(5V) TAL UNIT flaw. Output Y : IC504-13pin Output Cb : IC504-11pin Output Cr : IC504-9pin Check soldering of IC504. Check cable between main unit and mon- itor or Check monitor. Unless specified, 8U-210063-1 A.VIDEO UNIT part. AVR-4810CI/AVR-4810...
Page 58
IC504-7pin : H(5V) TAL UNIT flaw. Output Y : IC504-13pin Output Cb : IC504-11pin Output Cr : IC504-9pin Check soldering of IC504. Check cable between main unit and mon- itor or Check monitor. ※ Unless specified, 8U-210063-1 A.VIDEO UNIT part. AVR-4810CI/AVR-4810...
Page 59
TAL UNIT flaw. Output Y : IC504-13pin Output Cb : IC504-11pin Output Cr : IC504-9pin Check soldering of IC504. Check Output of cable between main unit and monitor or Check monitor . ※ Unless specified, 8U-210063-1 A.VIDEO UNIT part. AVR-4810CI/AVR-4810...
Page 60
IC504-7pin : H(5V) TAL UNIT flaw. Output Y : IC504-13pin Output Cb : IC504-11pin Output Cr : IC504-9pin Check soldering of IC504. Check cable between main unit and mon- itor or Check monitor. Unless specified, 8U-210063-1 A.VIDEO UNIT part. AVR-4810CI/AVR-4810...
Page 61
2.7. ZONE2 MONITOR OUT (COMPONENT) Output NG ZONE2 MONITOR OUT (COMPONENT) Output NG. When checking operation, select DVD for the function. Turn on ZONE2 and check Check ZONE2 is power on. again. Input Input Input CVBS COMPONENT No output No output AVR-4810CI/AVR-4810...
Page 62
IC401-7pin : H(5V) soldering, or DIGITAL UNIT flaw. Output Y : IC401-13pin Output Cb : IC401-11pin Output Cr : IC401-9pin Check soldering of IC401. Check cable between main unit and mon- itor or Check monitor. Unless specified, 8U-210063-1 A.VIDEO UNIT part. AVR-4810CI/AVR-4810...
Page 63
When checking operation, select DVD for the function. (COMPONENT1 Input) Checking the video convert ON/OFF settings. Video convert ON Video convert OFF Input Input Input Input Input Input Input Input CVBS COMPONENT HDMI CVBS COMPONENT HDMI No output To troubleshooting 3.HDMI/DVI. AVR-4810CI/AVR-4810...
Page 64
Check input/output of AMP. Check soldering of IC115 and Input : IC115-5pin surrounding parts. Output : IC115-7pin Check output to 8U-310030 DIGITAL UNIT. Check soldering of CX111. Output V : CX111-1pin To troubleshooting 3.HDMI/DVI. Unless specified, 8U-210063-1 A.VIDEO UNIT part. AVR-4810CI/AVR-4810...
Page 65
Input C : IC114-5pin and surrounding parts. Output Y : IC113-7pin Output C : IC114-7pin Check output to 8U-310030 DIGITAL UNIT. Check soldering of CX111. Output Y : CX111-9pin Output C : CX111-11pin To troubleshooting 3.HDMI/DVI. Unless specified, 8U-210063-1 A.VIDEO UNIT part. AVR-4810CI/AVR-4810...
Page 66
Output Cr : IC503-9pin Check soldering of IC503 and surrounding parts. Check output to 8U-310030 DIGITAL UNIT. Output Y : CX111-7pin Check soldering of CX111. Output Cb : CX111-5pin Output Cr : CX111-3pin To troubleshooting 3.HDMI/DVI. Unless specified, 8U-210063-1 A.VIDEO UNIT part. AVR-4810CI/AVR-4810...
Page 67
Is the DVD player's HDMI referring to the DVD player's output setting correct? operating instructions. When using a DENON DVD player, is the fluorescent display tube's "HDMI" indicator lit? If using a non-DENON DVD player, proceed to "YES". Are the picture and sound...
Page 68
TV's operating instructions. Are the picture and sound output when a different TV is used? The TV is defective. Check the set (AVR-4810CI) Check the set's input setting, Is the set's input set to HDMI? referring to the set's operating instructions.
Page 69
Is other transistor trouble? Replace the transistor. Is other resistance trouble? Replace the resistance. Turn on power, check that voltage of the section is normal and that idling electric current is flowing. AVR-4810CI/AVR-4810...
IC514/ IC515) transmitted to 8U-310045 CX505? Check IC513, IC514 and IC515 Connect the connectors properly. soldering. Once more, checking the connection of the connector. When can specify the trouble of the channel and function, check the signal route where it corresponds. AVR-4810CI/AVR-4810...
Page 71
Set the IP address and other parameters properly. For a fixed IP setting, check whether the IP address is redundant with that of Are the AVR-4810CI network settings correct? other devices, and check whether the subnet mask setting is correct.
Page 72
Checking the set (AVR-4810CI) Is the antenna cable con- Connect the antenna cable nected to the network mod- to X1 on the network mod- ule? ule. Is the network module properly connected to CX304? Connect the network module properly into CX304 .
Page 73
Is the USB device compatible with the set? compatible devices and iPod (Remove some models) are sup- ported. Checking the set (AVR-4810CI) Is the wire properly connected between CX052 and CY052? Connect the wire properly. Is a voltage (5V) being supplied between pins 1 and 4 of JK451 (back panel USB connector) and JK981 on the 8U-210063-3 cir- The TR452 and TR453 periphery circuitry is defective.
Page 74
6.3. No picture or sound is output If no picture is output Checking the set (AVR-4810CI):( Is the wire properly connected between CX061 and CY061? Connect the wire properly. The circuit from CX304 to IC457 or network module is defec- Are video signals output from CY061 pin 4 (Y) and pin 6 (C)? tive.
Page 89
1. Pin names in brackets [ ] represent a functional signal as a whole and should not be considered as two separate pins. 2. The position of pin number 1 varies by product. Refer to the index mark in attached “Package Dimensions”. AVR-4810CI/AVR-4810...
Page 90
External memory access pin(NC) P55/HOLD/ HOLD/FRASH EPM M3VPu External memory access pin(NC,Pup)/Rewrite boot program start : L input set P54/HLDA HLDA External memory access pin(NC) P133 MUTE POWER/ For MUTE +B control pin/For extended ROM 3.3V control pin ROM POWER AVR-4810CI/AVR-4810...
Page 92
M3VPu Button input2 136 P104/AN4/ KEY1 M3VPu Button input1 137 P103/AN3 SUB UPDATE SUB UPDATE mode control(DPMS/DENON WRITTER) (MAIN: L/ SIB:H) 138 P102/AN2 MIC DET/H/P DET/X2 SW3VPu MIC detect pin/Headphone/voltage-doubler detect pin/LIMIT PROT/LIMIT judge signal detect input (A/D detect )
Page 93
DIR CE4 DIR control pin (LC89058W-VF4A) RESET SUBRESET SCPU3VPu Reset input XOUT Oscillator connection Oscillator connection +3.3V P85/NMI/(CEC) NMI/(CEC_IN) Fixed to H P84/INT2 CEC_IN SCPU3VPu CEC-D signal input pin E↓&L P83/INT1 ACK SIMO E↓&L MAIN-SUB μcom comm. control input pin AVR-4810CI/AVR-4810...
Page 94
GUI ROM rewrite control (ACTIVE"L") P77/(CLK5) /TDO /PLDrewrite control (JTAG) P76/(TXD5) A PLD CS /TMS/ A PLD control pin /PLD rewrite (JTAG)/DENON WRITTER/For MITSUBISHI rewrite distinction "D/M" (DW="L") A PLD DATA/TDI A PLD control pin /PLDrewrite control (JTAG) A PLD CLK/MTCK...
Page 95
AD +3.3V P97/(SIN4) Tx EN AD8195 ENABLE pin for Front HDMI control P96/(SOUT4) DSP1 FLAG0/ DSP1 control pin (ADSP-21367)/FPGA rewrite SUBCONF_DONE control (MAIN FPGA & GUI FPGAcombined use) 100 P95/(CLK4) VEXP DIN VIDEO expander control DATA output (MCI 4094) AVR-4810CI/AVR-4810...
Page 103
SBCK cloc k output ter minal (32fs , 64fs , 128fs) SLRCK SLRCK cloc k output ter minal (fs/2, fs , 2fs) SDIN Ser ial audio data input ter minal DGND Digital GND DVDD Digital power XMCK Osc. amp output ter minal AVR-4810CI/AVR-4810...
Page 104
Ser ial audio data input f or modulation/Gener al I/O in/output ter minal TXO/PIOEN Modulation data output/ Gener al I/O enab le input ter minal * For latch-up countermeasure, perform each power supply ON/OFF in the same timing. BU9450KV-E2 (DI : IC106) Lot No. 1PIN AVR-4810CI/AVR-4810...
Page 105
BU9450KV-E2 Terminal Function AVR-4810CI/AVR-4810...
Page 107
V SSA1 32, 33 C-bus V SSA2 control 1, 20, 22, 5, 18, 38 6, 17, 39 23, 26, 29 MBH787 res. RTCI V SSD1, V DDD1, V SSD2 , V DDD2 , V SSD3 V DDD3 AVR-4810CI/AVR-4810...
Page 116
Chip select data input Input/Output Parallel data input/output — Power supply — Functional Block Diagram Chip-select C Bus transceiver Shift register Output data Input/output I/O setting Input data Output data data latch latch latch Input data Power-on I/O port reset AVR-4810CI/AVR-4810...
Page 117
FAN2 FLAG "H", Unusual: "L") MA : IC704 EXPE 5 Not used EXPE 6 Not used EXPE 7 Not used FAN drive voltage detect pin (Observe it only at FAN ON1=H. Normal: "H", EXPE 8 FAN DET Unusual: "L") AVR-4810CI/AVR-4810...
Page 118
MA : IC505 EXP29 PRE Z2 MUTE PRE OUT MUTE control EXP30 PRE Z3 MUTE PRE OUT MUTE control EXP31 232C CONTROL SUB LOG MODE 232C course switching control EXP32 XM BUS POWER XM ANTENNA BUS Power supply control pin AVR-4810CI/AVR-4810...
Page 123
PRINTED WIRING BOARDS 8U-110047 FRONT P.W.B. UNIT (1/2) COMPONENT SIDE AVR-4810CI/AVR-4810...
Page 124
8U-110047 FRONT P.W.B. UNIT (2/2) FOIL SIDE AVR-4810CI/AVR-4810...
Page 125
8U-110048 POWER SUPPLY P.W.B. UNIT (1/2) COMPONENT SIDE AVR-4810CI/AVR-4810...
Page 126
8U-110048 POWER SUPPLY P.W.B. UNIT (2/2) FOIL SIDE AVR-4810CI/AVR-4810...
Page 127
8U-110049 P.AMP P.W.B. UNIT (1/2) COMPONENT SIDE AVR-4810CI/AVR-4810...
Page 128
8U-110049 P.AMP P.W.B. UNIT (2/2) FOIL SIDE AVR-4810CI/AVR-4810...
Page 129
8U-110067 SPEAKER P.W.B. UNIT (1/2) COMPONENT SIDE AVR-4810CI/AVR-4810...
Page 130
8U-110067 SPEAKER SUPPLY P.W.B. UNIT (2/2) COMPONENT SIDE AVR-4810CI/AVR-4810...
Page 131
8U-110074 SPEAKER P.W.B. UNIT COMPONENT SIDE FOIL SIDE AVR-4810CI/AVR-4810...
Page 132
8U-210063 A.AUDIO/ VIDEO P.W.B. UNIT (1/2) CX671, CX672, CX611: Insert the connector to reverse with the screenprinting. COMPONENT SIDE AVR-4810CI/AVR-4810...
Page 133
8U-210063 A.AUDIO/ VIDEO P.W.B. UNIT (2/2) FOIL SIDE AVR-4810CI/AVR-4810...
Page 134
8U-210064 MAIN CPU P.W.B. UNIT COMPONENT SIDE FOIL SIDE AVR-4810CI/AVR-4810...
Page 135
8U-310030 DIGITAL P.W.B. UNIT (1/4) COMPONENT SIDE AVR-4810CI/AVR-4810...
Page 136
8U-310030 DIGITAL P.W.B. UNIT (2/4) COMPONENT SIDE AVR-4810CI/AVR-4810...
Page 137
8U-310030 DIGITAL P.W.B. UNIT (3/4) FOIL SIDE AVR-4810CI/AVR-4810...
Page 138
8U-310030 DIGITAL P.W.B. UNIT (4/4) FOIL SIDE AVR-4810CI/AVR-4810...
Page 139
8U-310045 DSP3/ ASSIGN P.W.B. UNIT (1/2) COMPONENT SIDE AVR-4810CI/AVR-4810...
Page 140
8U-310045 DSP3/ ASSIGN P.W.B. UNIT (2/2) FOIL SIDE AVR-4810CI/AVR-4810...
Page 141
Indicates number of zeros after efective number. (0 or 1) (More than 2) 2-digit effective number. 2-digit effective number. ・ Units:pF ・ Units:pF ・ When the dielectric strength is indicated in AC,"AC" is included after the dieelectric strength value. AVR-4810CI/AVR-4810...
Page 194
EXPLODED VIEW s EU,EC model This Illustration is AVR-4810CI model Digital Unit Sub Assy EU,EC model EU,EC model I-10 E2 model I-20 A-15 I-19 I-17 I-16 C-11 C-10 I-18 A-14 C-3 7 BK model SP model I-14 I-15 C-1 2...
Page 195
FRONT USB UNIT FRONT HDMI UNIT HD RADIO CON. UNIT EU, EC MAIN CPU UNIT 8S6331003000D DIGITAL UNIT SUB ASSY(AVR4810E3) EU, EC 8S6331003001D DIGITAL UNIT SUB ASSY(AVR4810E2) E2 8U-310045 DSP3/ASSIGN UNIT ASSIGN UNIT DSP3 UNIT CD/PHONO UNIT FAN DRIVE UNIT AVR-4810CI/AVR-4810...
Page 196
BKE2 8S4151002102D DOOR SUB ASSY SPE2 00D4010195202 HINGE (L) 00D4010195231 HINGE (L) 00D4010196201 HINGE (R) 00D4010196230 HINGE (R) 00D1310169038 DENON BADGE 00D1310169041 DENON BADGE 412010016001D KNOB(F) ASSY 412010016018D KNOB(F) ASSY 00D1140203009 KNOB RING(F) 00D1140203025 KNOB RING(F) 412010017004D KNOB(M) ASSY 412010017011D...