Specifications - Alpine MRV-M500 Service Manual

Specifications

Power Output
T.H.D. (Gain VR Min Position)
Residual Noise (Input Short)
S/N Ratio (Input Short)
Frequency Response
Output Offset Voltage at 4ohm (No Signal)
Input Sensitivity
(Ref.Output 300W/4ohm, 100Hz)
LPF Characteristic
(Ref.Output 1W/4ohm, 100Hz)
BASS-EQ Characteristic (VR Min = 0dB Setting)
(Ref.Output 1W/4ohm, 100Hz)
Pre-Out Level
(Ref. RCA-INPUT 1Vrms,100Hz)
Remote Bass Control
(Ref.Output 1W/4ohm, 100Hz)
Remote On Voltage
Current Drain
Input Impedance (Reference)
Fuse Requirement
Power Source
Dimensions (W x H x D)
Weight
NOTE : Due to Continuing product improvement, specifications and designs are subject to change without notice.
(1) 20Hz, 4ohm, 1.0% T.H.D. (14.4V)
100Hz, 4ohm, 1.0% T.H.D. (14.4V)
(2) 20Hz, 2ohm, 1.0% T.H.D. (14.4V)
100Hz, 2ohm, 1.0% T.H.D. (14.4V)
(1) 10W/4ohm at 20Hz / 100Hz (14.4V)
300W/4ohm at 20Hz / 100Hz (14.4V)
(2) 10W/2ohm at 20Hz / 100Hz (14.4V)
500W/2ohm at 20Hz / 100Hz (14.4V)
(3) 350W/1ohm at 20Hz / 100Hz (14.4V)
(1) NON-FILTER + AUX-0025
(2) 20KHz LPF + IHF-A
(1) Ref.Output 1W/4ohm, CEA-2006-A
(2) Ref.Output 300W/4ohm
(1) Ref.Output 1W/4ohm, 100Hz
* Volume Position : MAX
* Volume Position : MIN
(1) 400Hz (VR Max Position)
(2) 50Hz (VR Min Position)
(1) 50Hz (VR Max Position)
(1) Level
(2) Frequency Response
(1) VOL MAX Position
(2) VOL MIN Position
(1) No Signal
(2) 1.0% T.H.D. at 2ohm, 100Hz
(3) Remote Current Drain
(4) Back Up Current Drain (after 5min.)
300W
300W
500W
500W
0.01% / 0.02%
0.20%
0.025% / 0.03%
0.30%
1.00%
2mV
Vol max : 560uV
Vol cent : 210uV
Vol min : 112uV
85dB
110dB
10Hz : -1.0±2dB
400Hz : -3.0±2dB
±30mV
SP-IN : <0.2V
RCA-IN : <0.09V
SP-IN : 10V±2dB
RCA-IN : 4V±2dB
-3.0±2dB
-3.0±2dB
12dB±2dB
0dB±2dB
10Hz : -3.0±2dB
60kHz : -3.0±2dB
0dBV±2dB
-20dB±2dB
6V~7V
1.5A
60A
< 0.53mA
< 0.1mA
10kohm<Zin<30kohm
30A(Peak) x 2 (For Battery Line)
DC14.4V (11~16V)
199.1 x 55 x 199.9mm
1.8kg