H3C S5560X-EI Series Configuration Manual page 51

Hide thumbs Also See for S5560X-EI Series:

Installation manual (89 pages)

Command reference manual (59 pages)

Installation manual (55 pages)

Table Of Contents

Table of Contents

# Create VSI vpnb and VXLAN 20.

[SwitchA] vsi vpnb

[SwitchA-vsi-vpnb] vxlan 20

[SwitchA-vsi-vpnb-vxlan-20] quit

[SwitchA-vsi-vpnb] quit

# Assign an IP address to Loopback 0. The IP address will be used as the source IP address of

the VXLAN tunnels to Switch B and Switch C.

[SwitchA] interface loopback 0

[SwitchA-Loopback0] ip address 1.1.1.1 255.255.255.255

[SwitchA-Loopback0] quit

# Create a VXLAN tunnel to Switch B. The tunnel interface name is Tunnel 1.

[SwitchA] interface tunnel 1 mode vxlan

[SwitchA-Tunnel1] source 1.1.1.1

[SwitchA-Tunnel1] destination 2.2.2.2

[SwitchA-Tunnel1] quit

# Create a VXLAN tunnel to Switch C. The tunnel interface name is Tunnel 2.

[SwitchA] interface tunnel 2 mode vxlan

[SwitchA-Tunnel2] source 1.1.1.1

[SwitchA-Tunnel2] destination 3.3.3.3

[SwitchA-Tunnel2] quit

# Assign Tunnel 1 and Tunnel 2 to VXLAN 10.

[SwitchA] vsi vpna

[SwitchA-vsi-vpna] vxlan 10

[SwitchA-vsi-vpna-vxlan-10] tunnel 1

[SwitchA-vsi-vpna-vxlan-10] tunnel 2

[SwitchA-vsi-vpna-vxlan-10] quit

[SwitchA-vsi-vpna] quit

# Assign Tunnel 1 and Tunnel 2 to VXLAN 20.

[SwitchA] vsi vpnb

[SwitchA-vsi-vpnb] vxlan 20

[SwitchA-vsi-vpnb-vxlan-20] tunnel 1

[SwitchA-vsi-vpnb-vxlan-20] tunnel 2

[SwitchA-vsi-vpnb-vxlan-20] quit

[SwitchA-vsi-vpnb] quit

# On GigabitEthernet 1/0/1, create Ethernet service instance 1000 to match VLAN 2.

[SwitchA] interface gigabitethernet 1/0/1

[SwitchA-GigabitEthernet1/0/1] port link-type trunk

[SwitchA-GigabitEthernet1/0/1] port trunk permit vlan 2

[SwitchA-GigabitEthernet1/0/1] service-instance 1000

[SwitchA-GigabitEthernet1/0/1-srv1000] encapsulation s-vid 2

# Map Ethernet service instance 1000 to VSI vpna.

[SwitchA-GigabitEthernet1/0/1-srv1000] xconnect vsi vpna

[SwitchA-GigabitEthernet1/0/1-srv1000] quit

[SwitchA-GigabitEthernet1/0/1] quit

# Enable dynamic ND entry synchronization for distributed VXLAN IP gateways.

[SwitchA] ipv6 nd distributed-gateway dynamic-entry synchronize

# Create VSI-interface 1 and assign the interface an IPv6 anycast address. The IP address will

be used as the gateway address for VXLAN 10.

Table of Contents

Need help?

Do you have a question about the S5560X-EI Series and is the answer not in the manual?

H3C S5560X-EI Series Configuration Manual page 51

Need help?

Related Manuals for H3C S5560X-EI Series

Related Products for H3C S5560X-EI Series

Table of Contents