Advertisement
Entering the Vehicle While it is Running via Remote Start
1.
Unlock the vehicle's doors using the remote keyless entry system. If the vehicle's doors are unlocked manually
using the mechanical key, the vehicle's security system will trigger (if the security system is armed prior to
activating the remote start system) and the engine will turn off. Turning on the ignition or pressing the unlock
button on the remote keyless entry transmitter will disarm the security system.
2.
Enter the vehicle.
3.
The engine will shut down upon opening any vehicle door, trunk, hatch or rear gate on 5-door / wagon vehicles.
4.
Using the factory ignition key (Turn start models) or Access key (Push start models), re-start the engine.
Remote Start Confi rmation Feature
Your remote start transmitter is equipped with a unique bidirectional confi rmation feature. This feature will allow the
transmitter's LED to display system status provided the vehicle and transmitter fall within the system's operating
range. Typical transmitter LED fl ash sequences are outlined below.
Transmitter LED Flash & Beep Sequence
Flash when button is pressed (no audible beep)
Two (2) long fl ashes (no audible beep) following remote start
activation (Transmitter button is pressed two (2) times within three
(3) seconds)
One (1) fl ash & one (1) beep following remote start activation
(Transmitter button is pressed two (2) times within three (3)
seconds)
Two (2) fl ashes & two (2) beeps following remote start activation
(Transmitter button is pressed two (2) times within three (3)
seconds)
One (1) fl ash every fi ve (5) seconds (no audible beep)
Three (3) fl ashes & three (3) beeps
Important Note: When taking your vehicle in for service, it is recommended that you inform the service personnel
that your vehicle is equipped with a remote engine start system.
Selectable Run-Time
The system is preprogrammed to run for fi fteen (15) minutes before automatically stopping. The programmed run time
can be changed to alternate times using the following procedure.
1.
Enter the vehicle and close all vehicle doors, trunk or rear gate.
2.
Verify that the transmission shifter is in the "park" position.
3.
Turn the ignition "ON" then "OFF", "ON" then "OFF", "ON" then "OFF", then back "ON" and leave on throughout
the programming process.
(ON/OFF ignition cycles must be completed within eight (8) seconds).
4.
The system will honk the horn the number of times corresponding to the
current run time setting.
5.
Open and close the driver's door to advance to the next run time setting.
The system will honk the horn the number of times corresponding to the
new run time setting.
6.
Run time selection mode will exit via turning off the ignition or thirty (30)
seconds of inactivity. Upon exit, the current run time selection will be be
stored.
This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
Note: Changes or modifi cations not expressively approved by the party responsible for compliance could void the user's
authority to operate the equipment.
Feature Description
Indicates that the system is transmitting an RF signal
Indicates that the transmitter did not receive remote start
activation confi rmation from the vehicle system. The transmitter
will automatically send one (1) additional remote start activation
attempt. This usually occurs when the operational range is at its'
limit or has been exceeded.
Indicates that the transmitter has received remote start activation
confi rmation from the vehicle system.
Indicates that the transmitter has received confi rmation of a
successful start from the vehicle system (vehicle is now running).
Indicates that the vehicle is running via remote start. If the
transmitter is moved outside of the system's operating range,
this sequence will time out after the default fi fteen (15) minute
run time.
Indicates that the engine has turned off due to the remote start
system fi fteen (15) minute time out, vehicle safety parameter or
normal shut down.
Horn Honks
1
2
3
4
Run Time
Three (3) Minutes
Five (5) Minutes
Ten (10) Minutes
Fifteen (15) Minutes
(Default Setting)
Advertisement
