Table of Contents
Advertisement
Quick Links
39412/SUBARU (P.01-09)
8/1/00 5:39 PM
INSTALLATION
INSTRUCTIONS
NOTE: This system requires prior installation of Keyless Entry
Page 1
System. If installing both systems at the same time, install the
Keyless Entry System first.
Kit Contents:
1
Security Control Module w/Integral Bracket
1
Starter Interrupt/Horn Relays w/Integral Bracket
1
Horn w/Integral Bracket
1
Security Radio Mounting Bracket
2
Pan Head Screws (M5×8mm)
2
M6 Nuts
2
Window Decals
1
Installation Manual
Tools Required:
#1 Flat-tip Screwdriver
#2 Phillips Head Screwdriver
Electrical Tape
1/4" Drive Ratchet
10-inch 1/4" Drive Extension
10mm Socket
This device complies with FCC rules part 15. Operation is
subject to the following two conditions: (1) this device may
not cause harmful interference and (2) this device must
accept any interference that may cause undesired operation.
SECURITY SYSTEM
UPGRADE
LEGACY
P/N: H7110LS200
1
00.08
UT28L-11
Printed in Japan
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Subaru LEGACY H7110LS200
Summary of Contents for Subaru LEGACY H7110LS200
-
Page 1: Security System
39412/SUBARU (P.01-09) 8/1/00 5:39 PM INSTALLATION INSTRUCTIONS NOTE: This system requires prior installation of Keyless Entry System. If installing both systems at the same time, install the Keyless Entry System first. This device complies with FCC rules part 15. Operation is... - Page 2 39412/SUBARU (P.01-09) 8/1/00 5:39 PM A. Pre-Installation Notes 1. Vehicle Preparation a. Lower the driver’s side window to avoid inadvertently locking the keys in the vehicle dur- ing installation. b. Disconnect negative battery terminal to prevent accidental shorting of any power circuits.
- Page 3 39412/SUBARU (P.01-09)5ÇÃÉRÉsÅ[ 8/28/00 11:42 AM 4. Lift the center console cover by carefully pulling outward in areas indicated by arrows in Figure 4. 5. Remove the six screws indicated by the arrows in Figure 5. Do not disconnect any connectors. Pull the unit out just far enough to access the passenger side of the unit.
- Page 4 39412/SUBARU (P.01-09) 8/1/00 5:40 PM C. Starter Interrupt and Horn Relay Installation 1. Remove the screw indicated by the arrow in Figure 1 and disengage the two plastic screws indicated by arrows in Figure 2, then remove the dash panel.
- Page 5 39412/SUBARU (P.01-09) 8/1/00 5:40 PM D. Horn Installation 1. Locate the AT resistor in the engine compartment. 2. Remove the bolt (M8) indicated by arrow A in Figure 1 and loose the bolt (M8) indicated by arrow 3. Mount the horn bracket by passing it behind the AT resistor in the engine compartment.
- Page 6 39412/SUBARU (P.01-09) 8/1/00 5:40 PM G. Valet Mode Test 1. Open the driver’s door and then depress and hold the UNLOCK/DISARM button on the remote for more than two seconds and the following should be observed: a. The status indicator (LED) will begin flashing 2x per second indicating that the alarm is in the valet mode.
- Page 7 39412/SUBARU (P.01-09) 8/1/00 5:40 PM I. Notes on System Operation 1. If the alarm is not deactivated within 30 seconds of triggering, the system will automatically reset. 2. The hood is not protected as a part of this system and therefore will not cause a triggering of the alarm when opened unless sufficient force is used in which case the shock sensor will trig- ger the alarm.
- Page 8 39412/SUBARU (P.01-09) 8/1/00 5:40 PM K. Finishing the Installation 1. Reverse steps 1 through 10 in section B. Installation Preparation, to reassemble radio, radio trim bezel, cup holder, ashtray, gear shift cover and parking brake trim. 2. Replace the lower dash panel below the steering column.
Need help?
Do you have a question about the LEGACY H7110LS200 and is the answer not in the manual?
Questions and answers