Table of Contents
Advertisement
Quick Links
Installation and operation manual
for
door drive LDO AC 3.0
Please read this operation manual before
starting installation and start-up,
make sure you understood the contents and pass the
manual to others, if necessary.
It provides instructions related to your safety and
.
helps to avoid damage to the door drive
Material No.27120424
Advertisement
Table of Contents
Summary of Contents for ETG LDO AC 3.0
- Page 1 Installation and operation manual door drive LDO AC 3.0 Please read this operation manual before starting installation and start-up, make sure you understood the contents and pass the manual to others, if necessary. It provides instructions related to your safety and helps to avoid damage to the door drive Material No.27120424...
-
Page 2: Table Of Contents
Contents Page Safety regulations Foreword 1 Definition of use 1.1 Intended use 1.2 Unacceptable use 1.3 Obligations of the installation company 1.4 Expansions and amendments 2 Technical description 2.1 System description 2.2 Functions 2.3 Operation elements and terminal layout on the board 3 Technical Data 4 Assembly and installation 5. -
Page 3: Safety Regulations
Scope of application and instructions This operation manual is intended for all individuals who take part in installation and start-up of door drive LDO AC 3.0. Instructions contained in the operation manual must be strictly followed. Other effective regulations In addition to this operation manual, the following regulations must be adhered to:... - Page 4 Accident prevention Every individual knowing and following accident prevention regulations helps with preventing accidents from happening! Precautionary measures against recognizable accident hazards may enable to avoid heavy damage. Every employee is obliged to prevent accidents and occupational diseases from happening to the best of their ability.
-
Page 5: Foreword
Foreword This operation manual describes the door drive for personal and cargo elevators LDO AC 3.0 according to EN81. The operation manual is divided into chapters. In Chapter 1, the intended use of the door drive is defined in a form of a use description. In Chapter 2, technical description of the door drive is provided, ensuring a good overview of its design and operation. -
Page 6: Definition Of Use
EN 81 standard. The installation company shall implement the entire operation manual of the door drive LDO AC 3.0 in the operation manual and operation instructions of the entire elevator installation, without changing or rendering a single point ineffective. -
Page 7: Technical Description
2 Technical description 2.1 System description The door drive LDO AC 3.0 is an "intelligent" door drive. Thanks to this drive, the elevator door may be opening and closing with regulated speeds and accelerations. The maintenance-free door drive comprises of a control system which is installed inside a housing, and of a drive in the form of a gear motor. - Page 8 The „Push“ command In the operational state of pushing, the state of the light barrier attached directly to the door drive is not observed and the closing speed is lowered. The commands „Push“ and „Door closing“ must be present simultaneously. Emergency release If the door is closed, the emergency release is possible under following conditions: when the door is in a standstill,...
-
Page 9: Operation Elements And Terminal Layout On The Board
2.3 Operation elements and terminal layout on the board Transducer inputs 4 – 0V „Door open“ 3 – 24 V DC button 2 – Channel B 1 – Channel A „Door closed“ button Signal inputs 6 – 0V DC 5 – 24V DC max 10 mA 4 –... -
Page 10: Technical Data
3 Technical Data Total permissible door leaf max. 200 kg in case of Type 200 max. 420 kg in case of Type 420 permissible door width max. 4000 permissible operating temperature max. 60 °C min. -10 °C Housing execution zinc-plated, installed on a foot, Housing cover lock 1 pc. -
Page 11: Assembly And Installation
With the determination of door width, the controller recognizes the connecting of the cables and rotates it in the inverter if necessary. 3. Open the housing cover of the door drive door drive LDO AC 3.0. 4. The incremental moment transducer is already factory installed on the drive motor after shipment and must still be connected to the CN3 connector (see Figure 4-1) (see table at 2.). - Page 12 6. Switch on the power supply. The indicator of the converter displays „000“, the PWR-LED and the Hz-LED light up. 7. Test of rotation direction of the generator: With the self study of the rotation direction of the motor in regard of the door width determination, the controller also recognizes the right rotation direction of the generator.
- Page 13 Door to button Dip switch 2 Figure 4-3 Controls used during door width estimation The door can be closed or opened using service buttons “Door closed” and “Door open”. In case of all door motions performed using the service buttons “Door closed” and “Door open”, the respective service buttons must be held until the “open”...
- Page 14 Relay contact “open” When the door is open, the corresponding opening contact at CN4 connector is closed (pins 1 and 2), while the closing contact is open (pins 2 and 3). If the door is not in that state, the opening contact is open and the closing contact is closed.
-
Page 15: Configuration
5 Configuration The door drive can be influenced using the following parameters: Standard 120 W Standard 180 W Parameter one- one- middle Indicator sided middle sided Setting range Description A021 Max. opening speed 5.00 – 50.00 Hz A022 Max. closing speed 5.00 –... - Page 16 Input status D006 Output status P062 estimated "Door closed" position P063 estimated "Door open" position A035 Version number Table 5-2 Indicator parameters Motion curve LDO AC 3.0 P064 A021 / A028 Moment A033 A032 Opening A026 A024 P066 P066 A027...
- Page 17 Navigation button Moves to the first parameter in the next group (function mode) Cancels parameter change Moves the cursor one digit to the right (digit input mode) Pressing and holding the button for 1s results in return to d001 parameter Forward button This button enables parameter changing or selection (increasing values).
- Page 18 6 Generator: The generator is located in the drive opposite the gear wheel. A magnet is mounted on the elongated output shaft using a magnet holder, which analyzes the magnetic field of the generator. The magnet holder can be axially slipped onto the shaft in order to define the separation distance. Generator mounting / configuration: Attach the foundation plate of the generator to the drive using spacers.
-
Page 19: Error Messages
7 Error messages Error Error cause Remedy The door does not move No power supply at the drive Check connection to the power supply network No commands are issued from the If the door is moved using the service buttons, elevator control system. - Page 20 Converter error messages: Directly readable at the screen after an error occurs Error messages are displayed with an error code E01.o – E83.o on the display. The digit after the decimal point indicates converter status at the time of error occurrence. .0 during the initialisation process at power supply switching or a RESET signal .1 during STOP status .2 during braking phase...
- Page 21 Checking the input signals : The D005 parameter indicates status of the input signal. The upper bar shows that there is no signal. The lower bar shows that a signal exists. Upper bar array Lower barr array Input opening Input closing Input pushing Input light grid Generator input...
- Page 22 Meaning of positions counted from the right: 1 Output door closed Output reversing Output door open 10/2015 Page 22 of 24...
- Page 23 Notes: Set values: A021 ……… A022 ……… A023 ……… A024 ……… A025 ……… A026 ……… A027 ……… A028 ……… A029 ……… A030 ……… A031 ……… A032 ……… A033 ……… A034 ……… P064 ……… P065 ……… P065 ……… 10/2015 Page 23 of 24...
- Page 24 Contents of a complete control unit Control system LDO AC 3.0/200 Control system LDO AC 3.0/420 Drive motor Toothed belts Cat.No.: Part Accessories kit 50100120 Screw M6x25 8.8 zn 50100175 U-disc DIN 125 A6.4 50110023 Verbus Ripp washer M6 50105310 Verbus Ripp screw M6x12 8.8 zn...