Operating A Tv Using The Remote Control (Universal Remote Control); Setting The Remote Control Code - Sharp DV-SR3U Operation Manual

Major Components
Front display CHANNEL
' ' /" ' ' " " " "
'
panel
20
Operating a TV Using the
Remote Control
(Universal Remote Control)
The Universal Remote Control may operate the
basic functions of 21 different types of TVs.
To enter the Manufacturer's Code for your TV,
follow the instructions below.
There is no guarantee that the universal
remote control will function with your TV.
Setting the
Manufacturer's Code
1
Press POWER and CH ' of TV
CONTROL simultaneously.
2
Enter the 2-digit Manufacturer's
Code with the Number buttons
(Ex. 02-"0", "2") within 10 sec-
onds after releasing POWER
and CH ' of TV CONTROL.
3
Point the remote control unit
towards the TV and then press
POWER of TV CONTROL.
• If the TV turns on/off, setup was
successful. If not, repeat the proce-
dure using another code.
See the list below for the Manufacturer's Code
and the buttons which work with each brand.
POWER
Buttons on the Remote
CH ' ' ' ' ' /" " " " "
Brand Code VOL
EMERSON 19
FISHER 17
FUNAI 06
GE 07, 09
GOLDSTAR 18
HITACHI 15
JVC 16
09
MAGNAVOX
11
MITSUBISHI 14
PANASONIC 13, 21
PIONEER 03
RCA 07, 09
SAMSUNG 20
SANYO 17
01
SHARP
02
SONY 10
TECHNOL ACE 04
TOSHIBA 12
05
ZENITH
08
NOTE
• If the batteries in the remote control unit are
changed, the code settings must be re-
entered.
• Some brands have more than one code
listed above, due to changes in the codes.
In such cases, try another code to find the
code that operates your TV.
Setting the Remote
Control Code
• Two types of remote control codes operate
this Recorder: RC-1 and RC-2. If you
operate this Recorder by remote control
along with another SHARP DVD recorder or
DVD player placed next to it simulta-
neously, switching the remote control code
(both the Recorder and remote control) to
one of the signals (RC-1 or RC-2) will let
you operate only with this Recorder.
• Make sure to set the Recorder and remote
control to the same remote code. You can
not operate the Recorder if they are not set
to the same code.
Setting the Remote Con-
trol Code of the Remote
Example: Setting the code to "RC-2".
1
Press and hold POWER and 2
together for more than 5 seconds.
2
Press POWER of this Recorder to
see if you can turn it on/off.
• If you cannot, go to step 3 .
NOTE
• The remote control code of the remote
becomes "RC-1" when you change the
batteries.
Setting the Remote Con-
INPUT
/
trol Code of the Recorder
× ×
× ×
3
Press POWER to turn off the
× ×
×
Recorder.
—
×
—
4
Press and hold CHANNEL" and
× ×
' on the Recorder together for
× ×
×
—
more than 5 seconds.
× ×
• Each time this operation is performed,
× ×
the code of the Recorder toggles
× ×
× ×
between "RC-1" and "RC-2". The front
×
—
panel display changes as the code
× ×
changes.
× ×
• Press POWER on the remote control
× ×
× ×
to see if you can turn on/off the
× ×
Recorder.
× ×
× × If remote control does not
× ×
work
×
—
Press POWER on the remote control and
check the front panel display (RC-1 or RC-2).
Set the remote control code according to the
display and press POWER to see if you can
turn on/off the Recorder.