haacon 220.0.3 Operating Instructions

OPERATING INSTRUCTIONS
(Translation)
Rope winch
Type 220.0,3
220.1
421.0,125 4210.0,08
1. USER GROUPS
Duties
Operator Operation,
visual inspection
Special- Assembly, disassembly,
ist per- repair, maintenance
sonnel
Tests
2. SAFETY INSTRUCTIONS
Appropriate use
Operate the equipment in accordance with the information in
these operating instructions.
– Only use to lift, lower and pull freely-movable loads.
– Only use when in perfect working order.
– Only allow to be operated by personnel instructed on how to do so.
Safety-conscious work
– First read the operating instructions.
– Always be conscious of safety and hazards when working.
– Observe lifting device and load during all movements.
– Immediately report any damage or defects to the person in charge.
– Repair equipment first before continuing work!
– Do not leave the load suspended without supervision.
– Transport device protected against impacts and shocks,
falling over or toppling.
The following are not allowed:
– Overload (--> technical data, type plate, payload plate)
– Mechanical propulsion.
– Impacts, blows.
Use exclusions
– Not suitable for permanent operation and vibration stress.
– Not approved for use as builders' hoist (BGV D7).
– Not approved for use on stages or in studios (BGV C1).
– Not approved for use as a retractable transportation device for per-
sonnel (BGR 159).
– Not approved for use in explosive areas/environments.
– Not suitable for aggressive environments.
– Not suitable for lifting hazardous loads.
Organisational measures
– Ensure that these operating instructions are always at hand.
– Ensure that only trained personnel work with the equipment .
– Check at regular intervals whether it is being used in a safety and hazard
conscious manner.
Installation, service and repair
Only by specialist personnel!
Only use original spare parts for repairs.
Do not modify or alter safety-relevant parts!
Additional attachments must not impact safety.
Further regulations to be observed are
– German Industrial Health and Safety Ordinance (BetrSichV).
– Country-specific regulations.
– German Accident prevention regulations (BGV D8).
Load
– Do not leave suspended without supervision.
– Do not allow to swing.
– Do allow to fall in the rope.
Rope
– Compliant with EN 12385-1 and EN 12385-4 and the
technical data
– Maintain rope deviation angle
non-rotating rope ≤ 3° (standard)
rotation-resistant rope ≤ 1.5°
– Use a rotation-resistant rope for unguided loads.
This can reduce the resting period of the rope (drive
mechanism group).
– Wind up the wire rope under pretension, e.g.
fully wind up the rope and adjust the rope length to the lift.
The length of the rope is correct if:
> 2
094003_k_gb_hseilw_s
Louis Reyners BV | Symon Spiersweg 13a, 1506 RZ Zaandam
GB
220.0,5 220.0,75
220.2 220.3
4210.0,125
Qualifications
Instruction by means of the operating
instructions; Authorised person 1
Mechanic
Authorised person 2 per TRBS-1203
(Technical expert)
≤3°
≤1,5°
> 1.5 x rope Ø
Lifting equipment
– Ensure sufficient load-bearing capacity.
– Only use load hooks with a safety flap.
– Use the approved load hooks with rope thimbles
and rope clip.
– Attach the load properly.
– Do not use the winch rope to secure the load.
3. TECHNICAL DATA
Тype
Order number
Order no. galvanised
Perm. load, first rope layer kg
Perm. load, last rope layer kg
Max. number of layers
Crank force N
Minimum load kg
Lift / crank rotation mm
Weight without rope kg
Rope take-up m
Rope diameter mm
Min. rope breaking force kN
+50° C
Тype
Order number
-20° C
Order no. stainless steel
Perm. load, first rope layer
Perm. load, last rope layer
Max. number of layers
Minimum load
Crank force
Lift / crank rotation
Weight without rope
Rope take-up
Rope diameter
Min. rope breaking force
Subject to design and implementation changes.
4. CONSTRUCTION
Rope winches with/without spur gear unit, recoilless safety crank and
maintenance-free slide bearings.
5. INSTALLATION
The winches' construction is sufficiently dimensioned, with flat mounting
surfaces. Fit the rope winch with bolts, washers and nuts and secure to
prevent from coming undone.
Type 421.0,125+4210.0,08+4210.0,125 2 x M8 bolts, min. 8.8
Type 220.0,3 + 220.0,5
Type 220.0,75 + 220.1
Type 220.2 + 220.3
6. FITTING THE ROPE
If rope is fed in incorrectly --> (spare parts diagrams)
the brake is ineffective!
It is best to hard-solder the end of the rope and lock it
to the rope drum.
When the crank is turned in a clockwise direction,
the rope should wind up.
7. OPERATION
Move the crank handle 90° into the working position.
To lift the load: turn the hand crank clockwise.
To lower the load: turn the crank anticlockwise.
If the crank is released during lifting or lowering, the load (≤ minimum
load!) is held in its current position.
Do not wind up the rope under load beyond the point where the rims
project at least 1.5 times the rope diameter above the coiled rope. This
avoids overloading the winch and prevents the rope from coming off the
drum at the side.
At least 2 winds of the rope must remain on the drum at all times.
The rope pulling force of the first layer is the same as the nominal pulling
force of the winch. The pulling force decreases for each additional layer
of rope (--> type plate, pulling force for first/last layer of rope).
Free running crank
– Operation under load:
≤3°
≤1,5°
Pull crank arm away from winch and rotate until the two coupling pins
engage into the coupling disc. Load can now be lifted or lowered.
– Free running operation:
Disengage coupling pins from disc by pushing crank arm towards the
winch. The crank is now free running and operational when there is no
load on the winch.
Warning!
The crank in free running position may only be used when there
is no load on the winch.
| +31 (0) 75 650 47 50
220.0,3 220.0,5 220.0,75 220.1
200047 200048 205047 200815 200051 200052
200335 200048 200049 203241
300 500 750 1,000
203 330 580 750
4 4 3 3
190 210 200 180
30 30 50 50
74 30 28 18.8
10 10 14 15
11 10 12 10
6 6.5 8 9
9.5 16 24 32
421.0,125 4210.0,08 4210.0,125
200044 203717 203718
210712
kg 125 80 125
kg 65 45 65
6 6 6
kg 30 30 30
N 170 170 170
mm 138 135 138
kg 4 2.5 2.5
m 15 20 15
mm 4 3 4
kN 4 2.6 4
4 x M12 bolts, min. 8.8
4 x M14 bolts, min. 8.8
4 x M16 bolts, min. 8.8
| info@lr.nl | www.LR.nl
220.2 220.3
2,000 3,000
1,700 2,500
2 2
320 300
50 100
16 10
23 32
8 7
12 13
64 96
1